Question about 2001 Dodge Ram 2500 Truck

1 Answer

Loose mirror in pop up housing

Pop up towing mirror. Mirror assembly is loose inside of pop up housing. Every time I hit a bump the mirror aims at the curb.

Posted by on

  • Anonymous Mar 28, 2014

    housing for side mirror is loose. how do i tighten the housing?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 75 Answers

On the inside of the door the mirror is mounted in behind the garnishing. You will have to open it up with a small screw driver...

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace side mirror[ mirror only],ford focus,driver side, 2013 model


If the mirror housing is in place, Have one cut to fit. Glue it in. If the housing is broken, replace all of it. You can't fix a broken side mirror. Tried to many times.

Oct 08, 2016 | Cars & Trucks

1 Answer

2001 F250 mirror loose, how to tighten?


the triangel cover on the inside towards the front of the door. pop it off and youll see three 10mm bolts that hold the whole housing to the door.

Apr 11, 2014 | 2001 Ford F-250 Super Duty

1 Answer

Loose screw rolling around in side view mirror assembly 1999 mazda miata


Usually the mirror is 'glued' to the moving parts of the inside. Most of the time one will need to remove the mirror and re-glue it back.

Feb 01, 2013 | 1999 Mazda MX-5 Miata

1 Answer

Lexus SC 430 car mirror will not adjust vertically?


As the miles and years pour on with a few examples, the side mirrors is an area that can cause some grief. Here is a brief write up on how to service the side mirrors on these cars.

Issue: Continuous clicking noise from mirror anytime the car is placed in reverse and the mirror only tilted half way down. Mirror was adjusted fine. My car is out of warranty.

Options:
1) New mirror-guessing here-$350.00-$500.00 installed.
2) Fix the current mirror using parts from another mirror. Mirror assembly does not need to be removed from car.

I picked up a side mirror for a pretty good deal off of Ebay and though it was not the correct color, I was only interested in the guts.

OK, first thing is to remove the mirror. Grab the mirror on the bottom and yank out with a quick tug towards you. The bottom of the mirror should pop out and then the top of the mirror slides out. You will then see the image below.Often times just one side of the bottom mirror comes out. Just pull on the other side.
E-These two leads are for the mirror heater. Just pry them out from the mirror using a flat head.
A-Those slots is where the top of the mirror slides into/out of during an R/R.
B-This is where the mirror snaps into/or out of during an R/R
C-Once the mirror is out of the way-remove this screw and the spring behind it. The white plastic square mirror holder can now be pulled out. Be gentle as there are two plastic worm bolts attaching this to the motor arms. Just give it a tug and work it out.
D-Now remove these 3 phillip screws which hold the front and rear housing together. This is the tricky part as on the bottom right Marked E is a plastic piece that snaps both pieces together. Moving the housing up and down will get it to lodge loose. In my case the tiny little clip snapped but no big deal
as the mirror goes back just fine. You may be able to pry into the inside end of the mirror by removing a plastic clip (not shown). Get this and everything else is easy.



F150 parts.

May 27, 2012 | 2003 Lexus SC 430

2 Answers

Someone hit my drivers side mirror an brokr it off, How to fix, both broke off on mirror housing?


Remove inside door panel,then mirror

Buy new mirror at dealer or salvage yard

Mar 14, 2011 | 1994 Buick LeSabre

1 Answer

How do you replace the exterior mirror glass on a 2007 chevy tahoe. I have the the replacement glass portion but not sure how to release the broken portion from the mirror motor. Thanks for any info!


i just replaced the passenger side on mine and this is what i did.

1. on the back side of the mirror housing is a half moon shaped plastic piece. gently remove that from the housing, exposing a portion of the back side of the mirror.

2. disconnect the two wires (remember rt and lf). carefully, with a pry tool, apply pressure on the center of the back side of the mirror, it will pop loose.

3. once the mirror is off there should be a round plastic piece attached to the back side of the mirror. on the passenger side there is a tab in the upper left side. lift up on the tab and slide the plastic piece down...it should slide off.

4. once you have the plastic piece off it goes on the back of the new mirror in the opposite way. you line up the four cross tabs and slide the mirror up until the tab grabs it.

5. put the mirror back in the housing by lining the circle (on back side center of mirror plate) with the center of the mirror housing. genlty apply pressure on the center of the mirror (i had to hit it firmly with the palm of my hand) unitl it snaps into place.

6. once it snaps into place you can reconnect the two wires to the back of the mirror and install the back side plastic housing......DONE

Mar 20, 2010 | 2007 Chevrolet Tahoe

1 Answer

R&R mirror itself on Driver's side door


On the Back of the mirror in the middle is a big plastic ring that is a pressure fitting you should be able to just pop the old one out and put the new one in. If you have to replace the whole assembly it's easy if you look at the inside of the door rigth where the mirror is attached there is a triangle piece of plastic you can just pop that off and there will be three bolts in side to remove the mirror if you have there should be some foam protecting the electrical wires inside that just comes out. Good Luck.

Jun 15, 2009 | 2001 GMC Sierra Crew Cab

3 Answers

Need to replace the passenger side mirror,glass only. does anybody know if the plastic backing plate the mirror is attached to pops out of the holder? If it does, it would make it easier to fit the new...


Just replaced the mirror glass myself. Don't have all the answers but can tell you this much.

The passenger side mirror on my 2004 Odyssey was hit by a projectile which caromed off the upper door frame. Left standing was a functional mirror base (motor driven part which has four, short, horizontally mounted rods) still attached to the mirror shroud and a separate assembly of the mirror glass and plastic mount.

I purchased the mirror glass alone online from a Honda dealer, removed the old mirror glass from the mount, and mounted the new mirror to the mount. To do this, look at the tabs which hold the mirror to the mount, and slide the mirror across the mount in the obvious direction. It will take some force. I had the benefit of having the mount/mirror glass blown out of the mirror shroud so it wasn't too difficult. If the broken mirror is still mounted to the mount and inside the shroud, push the bottom of the mirror inward so the top edge of the mirror can clear the top of the shroud. Then pull up on the mirror glass to slide it off the mount. This will take some force but fortunately, the mirror glass is already broken so you don't have to be gentle. Wear gloves or protect you hands while doing this.

Reverse the process for install the new mirror glass.

Now for my key tip. I had to remount the plastic mount/mirror glass assembly onto the motorized mirror base. I could see that it snapped in, with proper alignment, by pushing straight in. I applied quite a bit of force and simply could not get it to snap in place. My solution, was to put the assembly in a 200F oven for 15 minutes to heat the plastic to make it more flexible. Using paper towels to handle to avoid burns, I aligned the closures with the four, small, horizontally mounted rods, and with a moderate amount of force, the assembly snapped into place.

Hope this makes sense. I believe most people will only have broken mirror glass and not have the plastic mount with mirror glass come off the motorized base as I did.

Apr 19, 2009 | 2004 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...