Question about Cars & Trucks

Open Question

Icannot remove the seat of my Qingqi Qm 150L 4A Motor bike

Motorbike Qingqi Qm150l 4A

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I fit power steering on a 4a-f engine?


no you can not total rack and pinion would need changed out .

Aug 22, 2016 | Toyota Corolla Cars & Trucks

2 Answers

How do you remove the driver side seat to replace the power seat motor? the seat is stuck al the way forward. the motor runs but the screws do not turn.


Hi William:
Usually the seats are attached to the floor by four bolts.
Removal is a matter of opening the door,
put something soft on the ground to protect your knees
With a flashlight, look under the seat to locate the bolts.
With a socket or combination wrench, remove the bolts
unplug any electrical connections,
PRESTO!
Out comes the seat.

Sep 08, 2015 | 2006 Pontiac Grand Prix

1 Answer

Gpr 125 power valve wont move when reving bike have new motor and cables valve moves freely have a 7.5 amp fuse under the seat any suggestions?


this is cars and trucks post to bikes?
im,guessing what it is , bike dont cut it.
motor bike does as does motorcycle.
http://www.fixya.com/motorcycles/troubleshoot

Jun 19, 2014 | Cars & Trucks

1 Answer

How to remove seat from sfm motor bike


Side of seat left hand side there's a lock put key in and turn fully lifting seat from rear

Feb 27, 2014 | Cars & Trucks

1 Answer

How do I remove the air in the tube on my front brake on a motorbike


u gutta bleed it--best explained from a clymer bike manual--library has them-maybe not for ur model but it such a general procedure-with some wrenches--need some new fluid to put in top resevoir as u open bottom nut near the brake to catch old stuf

Sep 11, 2013 | Cars & Trucks

1 Answer

Replacing oil pan in 1990 Toyota Corolla


Vehicles covered: Toyota Corolla, 4A-F, 4A-FE, and 4A-GE Engines

Here's your maintenance manual entry for the complete procedure:

OIL PAN REMOVAL & INSTALLATION - 1990 Toyota Corolla

4A-F, 4A-FE and 4A-GE Engines

See Figures 1 through 7

1. Disconnect the negative battery cable.

2. Raise and safely support the vehicle.


2_19_2012_5_49_50_am.jpg


Fig. 1: Exploded view of the oil pan assembly-4A-F and 4A-GE engines

3. Drain the engine oil into a suitable container.


2_19_2012_5_50_48_am.jpg


Fig. 2: Remove the oil pan drain plug to drain the engine oil from the crankcase

4. Place a jack under the transaxle to support it.

5. Remove the splash shield from under the engine.

6. Raise the jack under the transaxle slightly.

7. Remove the front exhaust pipe between the exhaust manifold and catalytic converter. Some models have an oxygen sensor, disconnect the oxygen sensor wiring.


2_19_2012_5_52_25_am.jpg


Fig. 3: Remove the front exhaust pipe for better access during oil pan removal

8. On the 4A-F and 4A-FE engines, remove the center mounting.



2_19_2012_5_53_31_am.jpg


Fig. 4: Remove the bolts and nuts retaining the center mounting-4A-F engine

9. Some 4A-FE engines and all 4A-GE engines are equipped with a stiffener plate. Remove the set bolts and pull the stiffener plate from the vehicle.

10. On the 4A-GE engines, unbolt and lower the flywheel housing under cover.

11. If equipped, remove the oil cooler hose and union from the oil pan. Remove the two nuts and nineteen bolts retaining the oil pan.

12. Insert a blade between the pan and cylinder block, cut off the applied sealer and remove the pan.




2_19_2012_5_54_52_am.jpg


Fig. 5: Insert a blade and tap lightly to loosen the oil pan free from the block

To install:

Note: Be careful not to drop any oil on the contact surfaces of the pan and block.

13. Using a razor blade and gasket scraper, remove all traces of packing (FIPG) material from the gasket surfaces. Thoroughly clean all main surfaces to remove loose material. Clean both sealing surfaces with non-residue solvent.


2_19_2012_5_58_22_am.jpg


Fig. 6: Apply a reasonable amount of sealant (FIPG) to the oil pan surface-except 7A-FE engine

14. Apply new packing (FIPG) 08826-00080 to the oil pan as shown. Avoid applying excessive amounts to the surface. Be especially careful around the oil passages.

Note: Parts must be assembled within 3 mins of application. Otherwise, the sealer (FIPG) must be removed and reapplied.

15. Install the oil pan over the studs on the block with the nineteen bolts and two nuts. Tighten the bolts to 43 inch lbs. (5 Nm). Make sure when you install the oil pan drain plug using a new gasket.



2_19_2012_5_59_41_am.jpg


Fig. 7: Tighten the 19 oil pan retaining bolts securely-4A-F, 4A-FE and 4A-GE engines

16. If equipped, install the oil cooler pipe, two new gaskets and union bolt. Tighten the union bolt to 18 ft. lbs. (25 Nm).

17. Install the front exhaust pipe (with new gaskets on either end of the pipe) to the manifold.

18. On the 4A-GE engines, install and secure the flywheel housing under cover if removed.

19. On the 4A-FE engines if removed, attach the stiffener plate. tighten the No. 1 bolt first then the 5 bolts in the sequence shown. Tighten to 17 ft. lbs. (23 Nm).

20. On the 4A-GE engines, attach the stiffener plate with the 3 set bolts and tighten them to 27 ft. lbs. (37 Nm).

21. Attach the center mounting and tighten the member side bolts to 38 ft. lbs. (52 Nm), plate side to 17 ft. lbs. (23 Nm).

22. Lower the jack from the transaxle.

23. Lower the vehicle, and fill the crankcase with the appropriate amount of engine oil. Engine oil crankcase capacity is 3.4 quarts (with oil filter change).
Above -9 degrees Fahrenheit, use 10W-40 motor oil, and above 10 degrees Fahrenheit, use 20W-50 motor oil.

24. Connect the negative battery cable, start the engine and check for leaks. If all is well, raise the vehicle slightly and install the engine splash cover.

25. Recheck the engine oil level, top off if necessary.

Feb 14, 2012 | 1990 Toyota Corolla

1 Answer

Cannot put top up on 1987 allante the latch is locked in and icannot open the latch on the pull down motor


There's a switch ( kinda same shape, color & operation method as your power seat switches) behind driver's seat near the 2 Boot/Top 'release' pull tabs,, it's mounted on the "roof" of the open compartment area behind the seats. Slide your hand along there til you feel it. It recycles the pull-down motor up & down & should release the top. Also try in the trunck, there's 2 hard plastic strings with loops at end,, pull & see if it releases it.

Oct 22, 2010 | 1987 Cadillac Allante

2 Answers

I am trying to locate the fuel pump in the 1990 Toyota Corolla with a 4A-F3 engine and I can't find it. I've looked under the back seat and in the trunk. Do you know where it is? I do not have the...


remove the bottom of rear seat. open the service door on rear floor. take out the bolts that hold fuel tank set plate to the fuel tank, then now you can remove fuel pump assembly.

Sep 24, 2010 | 1990 Toyota Corolla

2 Answers

How do I change the distributor


REMOVAL NOTE: Once the distributor is removed, the engine should NOT be turned or moved out of position. Should this occur, please refer to the engine rotated installation procedure. Distributor components — 4A-F engine 88272p61.jpg
Fig. 1: Exploded view of the distributor — 4A-F engine 88272g41.gif
Fig. 2: Exploded view of the distributor — 1993 4A-FE and 7A-FE engines 88272g42.gif
Fig. 3: Exploded view of the distributor — 1996–97 4A-FE and 7A-FE engines 88272g43.gif
Fig. 4: Exploded view of the distributor — 4A-GF engine 88272g44.gif
  1. Disconnect the negative battery cable.
  2. Disconnect the distributor wire(s) at its harness. Loosen the screws holding the cap onto the housing 88272p05.jpg
    Pull the cap and wires off the distributor housing 88272p06.jpg

  3. On the 4A-F engines, disconnect the vacuum advance hoses. NOTE: On some models the distributor wires are part of the cap and can not be separated.
  4. Remove the distributor cap. Label and disconnect the wires from the cap. On some engines it will be necessary to use a flat bladed tool to lift up the lock claw and disconnect the holder from the cap. Fig. 5: On some engines, use a flat bladed tool to lift up the lock claw to disconnect the holder from the distributor cap 88272g45.gif

  5. Carefully note the position of the distributor rotor relative to the distributor housing (also note position of distributor to the engine assembly); a mark made on the casing/housing will be necessary for reassembly. Use a marker or tape so the mark doesn't rub off during handling of the case/housing. Mark the position of the rotor relative to the distributor housing 88272p07.jpg
    Label and remove all vacuum hoses attached to the advance on the distributor if equipped 88272p14.jpg
    If necessary, remove the rotor 88272p08.jpg

  6. Remove the distributor hold-down bolts. Remove the distributor hold-down bolts before pulling the unit from the engine 88272p13.jpg

  7. Carefully pull the distributor from the engine assembly. Remove the O-ring from the distributor shaft. Pull the distributor straight out from the engine 88272p15.jpg
prev.gif next.gif

Aug 13, 2010 | 1996 Toyota Corolla

2 Answers

How do i make my motor bike exhaust louder with any cost?  MOTORBIKE!


you could buy a shorter exhaust or just cut your old one short. that would make it louder the shorter it is the louder it goes

Dec 24, 2008 | 1990 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...