Question about 1994 Honda Civic Del Sol

1 Answer

Replace power window motor/regulator

Can someone give me a quick step by step on removing the old power windor motor and regulator so i can throw in a new one? Both doors on a 94 del sol. Thanks!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Too much to explain here. but a repair manual should tell you step by step on how to replace it.

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace power window motor


Remove the inner door panel
& window regulator/motor

Watch You Tube Video, on any vehicles
window regulator R&R

NO Parts get replaced, until you learn how they work,
& how to test them

Don't want to throw new parts at good ones, do you

Sep 28, 2014 | Dodge Grand Caravan Cars & Trucks

1 Answer

How to replace electric window motor and regulator on 1985 buick park ave


you need to remove the door panel on the door in question be careful to remove any hidden screws. there is a weather barrier that is glued to the door remove but don't tear it up to bad this is the protection for electrical components against water in the door panel. after removing panel and weather barrier I would turn the ignition on unplug the motor wire connector and operate the switch and see if you are getting power. if you are not getting power there is another problem. if you are getting power then remove the bolts securing the window to the regulator, this will probably require unbolting the regulator from the door to gain access to the bolts. after window is un bolted you can either remove the window track moldings and remove the window or use suction cups above the window moldings to hold window in place while removing regulator. replace in reverse order and your done. also be careful if you remove motor from regulator some have a spring on the regulator to assist in the operation of the motor and when motor is removed the regulator will release and spin not a good thing if your fingers are in the path.

Aug 25, 2014 | Buick Cars & Trucks

1 Answer

How do I replace the window motor on a 1995 mazda 626? What are the steps to replacing the motor/regulator?


Glass & Regulator
  1. Lower the window glass and remove the inner handle cover, door lock knob (if necessary), the window regulator handle and the door trim panel.

On vehicles with power windows, disconnect the wiring couplings.

  1. Carefully peel off the door screen so that it can be reused.
  2. Replace the window regulator handle and position the door glass so that the door glass installation bolts can be removed from the service hole.
  3. Remove the door glass installation bolts.
  4. Remove the door glass. Remove the regulator installation bolts, and then remove the regulator through the service access hole. Remove the window motor mounting bolts and separate the motor from the regulator.
  5. Installation is the reverse of the removal procedure. If the vehicle is equipped with power windows, connect the leads of the motor to a battery and run the regulator to the down position before installing the motor. Cycle the window several times to make sure that everything is in good working order.
shinehutt_43.gif
hope this helps
plz vote comment if need more help reply

Jan 18, 2011 | Mazda 626 Cars & Trucks

1 Answer

MY DRIVE SIDE POWER IS NOT WORK WHAT CAUSE WINDOR NOT WORKING . WHERE IS POWER WINDOR MOTOR LOACTED.


it could be the switch on the door . or the window motor itself most of the time its the motor. the motor is located in the door

Jul 11, 2010 | 1999 Dodge Caravan

1 Answer

How to replace a electric motor for power window in 1994 honda accord


How to Replace a Window Regulator (with Motor)
(DIY Complexity: Moderate / DIY Time: 2.8 hours)

Parts:
1. Window Regulator

1ed581e.jpg


Tools:
1. Screwdriver
2. Trim Panel Removal Tool
3. 3/8 in. Drive Ratchet
4. Socket Set
5. Riveter Kit

Steps:
Step 1 Remove the door panel by removing the handles and switches. It is required to unscrew or unclip the panel.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Refer to the vehicle specific service manual if available. There are several fragile plastic clips and hidden screws on the door panel that will break if removed improperly.

Step 2 Remove the vapor barrier.

Step 3 Disconnect the glass from window regulator.

Step 4 Tape the glass to door frame. The glass should not require removal.
o Tip: Tape the glass out of the way to allow access to the window regulator and window lift motor assembly.

Step 5 Disconnect the electrical connector from the window motor.

Step 6 Remove the window regulator mounting bolts. Slide the regulator assembly out through the interior access opening of the door. Remove the motor.

Step 7 Attach the original motor to the new window regulator and install the regulator assembly. Tighten the mounting bolts.

Step 8 Reconnect the electrical connector to the window motor.

Step 9 Install the window back onto the window regulator.

Step 10 Re-install the vapor barrier.

Step 11 Re-install the door trim panel and handles/switches.

Step 12 Test the power window for proper operation by rolling the window up and down in complete cycles for proper testing.
o Tip: After re-installing a window lift motor and regulator, it may be necessary to re-program it following manufacturer specific instructions. Not following or performing this step may result in improper power window function.


Hope helps (remember comment and rated this).

Jun 18, 2010 | 1994 Honda Accord

1 Answer

How do i change window motor in drivers side of 2000 toyota sienna


Hai,

Here are complete step-by-step instructions (with photos) on how to remove a door panel:

http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/remove-a-door-panel-from-any-vehicle-without-a-diagram

Here are complete step-by-step instructions (with photos) on how to test a power window motor to determine whether the problem is in the motor/regulator or the switch/wiring

http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator

First remove the inside door panel. It's attached by snaps around the perimeter. Pry between the panel and the door with a screwdriver, moving the screwdriver to a place where the panel is most solidly attached, and pry hard there so the snap releases. Then work around the panel to unsnap all the others. There may not be snaps at the top, but instead you lift the panel after unsnapping the bottom and sides. You probably also have to remove anything that's attached to the panel or that goes through it, usually attached with screws, maybe with pry-off cover plates. But do the snaps first and you'll be able to tell where else the panel's attached.
Then remove the lower part of the plastic waterproofing sheet, by pulling it away from the mastic around the perimeter. Pull up just enough to get at the motor mounting bolts.
Then undo those bolts with a wrench, and remove the complete motor and regulator assembly. The end of the long arm of the regulator will have a knob, which fits into a slot on the track at the bottom of the window. You'll have to slide it along the track till the slot gets wider to allow the knob to pull out.
You'll probably have to separate the motor/gear assembly from the regulator assembly. Buy a new or reconditioned motor/gear assembly from a parts store or junkyard or online. They'll probably want your old one in exchange (except the junkyard).

May 19, 2010 | 2000 Toyota Sienna

2 Answers

1998 Corvette power window


It sounds like you have power coming out of the switch to the motor because of what you hear. So that pretty much leaves you with a window regulator problem. Make sure there's no binding action between window & frame

Oct 17, 2009 | 1998 Chevrolet Corvette

2 Answers

All but one window not working


could be the computer controler in the drivers door stopping the others from working ,if so this is mega money ,just rewire a feed direct to each switch on the respective door

Jul 17, 2009 | Hyundai Motor 2004 Sonata

2 Answers

Installing new power window motor on a 1980 Corvette. Having some problems. Where does the window regulator need be for you install new motor? all the way up,down,middle etc. Need some tips not working...


You will need to roll the window down approx half way and you can either feel with your finger or get a small mirror to place in the door. You are looking for a hole in the regulator gear that will align with a hole in the main section of the regulator that bolts to the door. Once these are aligned you need to install a bolt through them and tighten it down. This will keep the regulator from moving when you remove the motor. Do not skip this step! If you remove the motor without this step you hurt yourself or even put a hole through your door. After you have the bolt in place you can remove the three bolts that hold the motor to the regulator.

May 06, 2009 | 1980 Chevrolet Corvette

2 Answers

1991 Chevy Blazer S10 window motor installation


http://www.a1electric.com/s10motor.htm. This link has pictures and step-by-step instructions. I found it and have both sides to replace. Hope this helps.

Aug 08, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1994 Honda Civic Del Sol Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...