Question about 1985 Chevrolet Chevy

Open Question

How to remove the grill on 86 k10

I need to remove the grill to get to the horns

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 104 Answers

SOURCE: which fuse is for the horn on a 86 k10

Fuse box are normally label identifying each fuse. Use a 12 volts test light and check all fuses and make sure none are blown.

Posted on Jun 13, 2009

Ad
  • 2309 Answers

SOURCE: '86 chevy k10; e.brake pedal is stuck

hold hte release had have somone pull the cable back form underneath the vehicle, with any luck only the front cable is stuck, if not use lots of penetrating oil to try to free the rear cables,

Posted on Nov 14, 2009

Testimonial: "I appreciate the quick response, I will try this ASAP! thanks alot!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the horn in my 06 h3?


I hope this info helps!~subyguru~
HORN REPLACEMENT

REMOVAL PROCEDURE

115128024

  1. Remove the grille.
  2. Disconnect the horn assembly electrical connector.
  3. Remove the bolt that retains the horn assembly to the radiator support.
  4. Remove the horn assembly from the body.
INSTALLATION PROCEDURE

115128024

  1. Install the horn assembly to the radiator support.
  2. Install the bolt that retains the horn assembly to the radiator support.
NOTE: Refer to Fastener Notice.

Tighten the bolt to 10 N.m (88 lb in) .

  1. Connect the horn assembly electrical connector.
  2. Install the grille.

May 08, 2012 | 2006 Hummer H3

2 Answers

The horn doesn't blow. at the horn relay,jumping 30/87 and the horn blows. terminal 85 is always +[positive],and this is correct.Terminal 86 is the ground for the 85/86 side of the relay. If I have the...


Your problem is most likely a defective clockspring assembly. This is also called "spiral cable assembly" it is located just under the steering wheel on the steering column and makes the connection between the main wiring harness and the circuits for the air bag and the horn. I cannot give you wire colors because your question did not mention year, make, model, engine size or whether the vehicle is equipped with cruise control or not. (cruise control makes a difference in the clockspring assembly used on your car.)

Anyway, the air bag and steering wheel has to be removed to fix it.

Dec 19, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

I'm trying to locate where the horn is under the hood of my 1996 camry.


Removal & Installation The horn is located behind the grille. Remove the grille retaining bolts to access. Unbolt the one screw holding the horn assembly to the bracket.


edd2bdd.gif
Remove the one bolt retaining the horn to the bracket

May 04, 2010 | 1996 Toyota Camry

1 Answer

'86 chevy k10; e.brake pedal is stuck


hold hte release had have somone pull the cable back form underneath the vehicle, with any luck only the front cable is stuck, if not use lots of penetrating oil to try to free the rear cables,

Nov 14, 2009 | 1986 Chevrolet K1500

1 Answer

Where is the horn located under the hood of a 2005 gmc canyon


Horn Replacement Removal Procedure

    1375741.gif
    tif.gif
  1. Remove the grille. Refer to Grille Replacement .
  2. Disconnect the horn assembly electrical connector.
  3. Remove the bolt that retains the horn assembly to the radiator support.
  4. Remove the horn assembly from the body.
Installation Procedure

    1375741.gif
    tif.gif
  1. Install the horn assembly to the radiator support.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the bolt that retains the horn assembly to the radiator support.
  4. Tighten
    Tighten the bolt to 10 N·m (88 lb in).
  5. Connect the horn assembly electrical connector.
  6. Install the grille. Refer to Grille Replacement .

Nov 07, 2009 | 2005 GMC Canyon

2 Answers

Horn location for a 1990 jeep cherokee


Hi RS,

The horn on my 86 Cherokee is inside the grill, in front of and to the right of the radiator. I don't imagine they've moved them too far from there in four years.

If you're trying to locate it for reasons other than it not working, I'd say have someone sound the horn while you stand in front of the car. That should pin point it.

Best regards

Mike

Oct 04, 2009 | 1990 Jeep Cherokee Limited

1 Answer

Which fuse is for the horn on a 86 k10


Fuse box are normally label identifying each fuse. Use a 12 volts test light and check all fuses and make sure none are blown.

Jun 13, 2009 | 1986 Chevrolet Chevy

1 Answer

Where is horn located o2008 x type jag


The horns are under the front, above the air splitter grille, (splash shield) Here are the steps for it.

  1. Remove the air splitter grill
Than
  1. Remove the three clips.
  2. Remove the air splitter grille.
Detach the horn assembly.

  1. Remove the horn assembly.
Than
  1. Disconnect the electrical connector.
  2. Remove the horn assembly.
Installation
  1. To install, reverse the removal procedure.

May 13, 2009 | 2008 Jaguar X Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...