Question about Cars & Trucks

Open Question

Removing rear seat to replace seat belt - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 29 Answers

SOURCE: automatic seat belt removal and replace with regular seat belts

You'd need to pickup the need parts at the junkyard. You'll need the "A" to "B" pillar trim, lower "B" pillar trim, front seat belts and seatbelt giude from a 1995 SC1 or SC2.

The treaded hole in the frame of the car where the track of the automatic seatbelt assembly attaches is in a slightly different place than the three point system. Its not a problem though. You just need to drill a 3/4" hole slightly above the existing hole in the trim panel. The existing hole is hidden by the seatbelt and not noticable at all.

Everything else pretty much bolts or snaps into place.

I've done this swap on several 1991-1994 Saturn S-Series.

Posted on Jan 27, 2009

mohammed387
  • 1952 Answers

SOURCE: replacing fuel pump need to remove rear seat need to know how

First you will need to releave fuel pressure......

next remove the rear seat cushion to gain access to fuel pump access panel.....

Removing Fuel Pump....

Posted on Jan 29, 2009

motor1258
  • 6674 Answers

SOURCE: how to remove rear seat from 2001 Audi allroad

Not 100% sure on yours but normally you'll either have a couple of bolts way down under seat cushion at front, near floor, or in some cases, you have to push seat cushion back toward rear window, hard & lift, to pop it out of notched catch under it.

Posted on Mar 14, 2009

  • 88 Answers

SOURCE: Replacing a rear seat belt in a 1998 Toyota Camry

if its centre belt remove rear seat to undo bolt out side one remove cover on upper belt to expose bolt

Posted on Jun 05, 2009

  • 185 Answers

SOURCE: remove rear seat lexus es300 2008

the bottom of the rear seat pulls straight up at the front and out. its pretty tight, you need to pull very firmly.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace the left rear seatbelt in my VW Jetta my10, how do I go about it?


all the jetta rear seats and seat belt parts
look the same sort of set up

fiddly job
back seat section or sections out
have to remove some plastics
to get to the retractable part of the belt ....looks like it is
under or mounted on the rear parcel shelf
undo the floor mount

then re thread and bolt the new seat belt in (pictured)

then replace the seats

26227982-baaqz4pc4guywvkqfm2wgc1t-4-0.jpg

26227982-baaqz4pc4guywvkqfm2wgc1t-4-1.jpg

Jun 29, 2016 | Volkswagen Jetta Cars & Trucks

1 Answer

How do i replace the park assist module in a 2011 chevy traverse???/


Have you checked the fuse? If so, the module is located behind the left rear trim panel. Remove the panel to access. Below is a diagram of the trim panel and location of the module in BLUE>
Preliminary Procedures
  1. Move the rear seat to the full forward position.
  2. Remove the rear number?2 seat . Refer to 3rd Row Seat Removal and Installation.
  3. Remove the rear quarter upper trim panel. Refer to Quarter Upper Trim Panel Replacement.
  4. Disconnect the liftgate actuator rod from the liftgate. Refer to Liftgate Actuator Rod Replacement.
  5. Disconnect the rear seat number 2 shoulder belt anchor bolt. Refer to Rear Seat Number 2 Retractor Side Belt Replacement.
  6. Remove the liftgate door sill plate. Refer to Liftgate Door Sill Plate Replacement.



woauitf41mzpgaaaabjru5erkjggg==

Nov 16, 2014 | 2011 Chevrolet Traverse

1 Answer

How is the rear seatbelt fixing replaced?


Remove the rear seat you will find the retaining bolts for the seat belt. Remove the bolts they are attached to the floor. Replace same way.

Aug 21, 2014 | Jaguar X-Type Cars & Trucks

1 Answer

How can i remove rear seats from my 2011 Vauxhall Insignia, also replace offside rear seat belt as I have had a mouse bite through the belt and the back seat


shoot the mouse !!!! ,,,, sorry coldnt resist ,,, you have to lift rear seatbase and boot carpet to get at the seat back bolts ,,, not a big problem ,,, the big one is getting at the seat belt because u have to remove alot of trim to get at the seat belt bolts ,,, alot of clips are involved that will break so source new clips before you start the job ,,,,rotten job so feel so sorry for you ,,,,

Dec 06, 2013 | 1992 Saturn SC

1 Answer

How to replace a rear seat belt for a land rover discovery


You have to probably remove the rear seat to get to the bolts and basically just remove bolts, replace seat belt and reinsert bolts and tighten.

May 27, 2010 | 2002 Land Rover Discovery Series II

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Replacing a rear seat belt in a 1998 Toyota Camry


if its centre belt remove rear seat to undo bolt out side one remove cover on upper belt to expose bolt

Jun 03, 2009 | 1998 Toyota Camry

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...