Question about Toyota Cars & Trucks

Open Question

Broken water inlet pipe 2006 toyota sienna le

Pipe leads to thermostat. do i need to remove intake plenum?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rsst
  • 175 Answers

SOURCE: I need to remove the upper intake manifold plenum.

There are no fasteners inside the plenum, The electrical connection for the injectors is very tight due to a rubber ring gasket the seals the injector assembly to the plenum. Carefully push down on the electrical assmbly while prying up the plenum. You also may have to remove the thermostat and hose. I've done this 3 times on my ladies 96 Yukon.

Posted on Jul 11, 2009

Ad
  • 1 Answer

SOURCE: Replacing RH Side view mirror on a 2006 Toyota Sienna

I had to replace my passenger side mirror on my 2004 Sienna a while back. I took some pictures as I did it. Maybe this can help.http://time4nothing.blogspot.com/2008/03/fixing-04-sienna-passenger-side-mirror.html

Posted on Oct 04, 2009

  • 154 Answers

SOURCE: 2006 Toyota Sienna Battery Drain. Side power

the sliding door is probablly draining the battery,, have door checked.. make sure tracks are clean and hinges are not binding

Posted on Dec 12, 2009

  • 1 Answer

SOURCE: toyota sienna interior lights not working

The problem is in the sunvisor light. You will have to take the light assembly off and you will find wires have become disconnected.

Daviscacare.com
757-689-4701

Posted on Jan 29, 2010

  • 1861 Answers

SOURCE: what is the towing capacity of a toyota sienna?

2006 Sienna Standard towing specs:

2WD or 4WD: Max Tongue Weight: 200 lbs
Max trailer and cargo weight: 2,000 lbs;
(over 1,000 lbs requires trailer brakes)

Max trailer and cargo weight: 3,500 lbs WITH the factory tow package

Thanks for using FixYa!

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intakegasket for grandam gt


Exactly what is the wrong? Need the part? Need to know torque adjust or porcedure to take off?

For
1994 Pontiac Grand Am 3.1L SFI OHV 6cyl check this procedure for Intake Manifold...
(see Figure 14)
The 3.1L engine is equipped with upper and lower intake manifolds. The upper intake manifold is also known as the intake manifold plenum.

CAUTION The fuel system is under pressure and must be properly relieved before disconnecting the fuel lines. Failure to properly relieve the fuel system pressure can lead to personal injury and component damage.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove top half of the air cleaner assembly and throttle body duct.
  4. Drain and recycle the engine coolant.
  5. Disconnect the EGR pipe from exhaust manifold.
  6. Remove the serpentine belt.
  7. Remove the brake vacuum pipe at the intake plenum.
  8. Disconnect the control cables from the throttle body and intake plenum mounting bracket.
  9. Remove the power steering lines at the alternator bracket.
  10. Remove the alternator.
  11. Label and disconnect the ignition wires from the spark plugs and wire retainers on the intake plenum.
  12. Remove the ignition assembly and the EVAP canister purge solenoid together.
zjlimited_601.jpg

Fig. 14: View of the intake manifold and related components

  1. Disconnect the upper engine wiring harness connectors at the following components:
    Throttle Position Sensor (TPS) Idle Air Control (IAC) Fuel Injectors Coolant temperature sensor Manifold Absolute Pressure (MAP) sensor Camshaft Position (CMP) sensor
  2. Tag and disconnect the vacuum lines from the following components:
    Vacuum modulator Fuel pressure regulator PCV valve
  3. Disconnect the MAP sensor from upper intake manifold.
  4. Remove the upper intake plenum mounting bolts and lift off the plenum.
  5. Disconnect the fuel lines from the fuel rail and bracket.
  6. Install engine support fixture special tool J 28467-A or an equivalent.
  7. Remove the right side engine mount.
  8. Remove the power steering mounting bolts and support the pump out of the way without disconnecting the power steering lines.
  9. Disconnect the coolant inlet pipe from the outlet housing.
  10. Remove the coolant bypass hose from the water pump and the cylinder head.
  11. Disconnect the upper radiator hose at thermostat housing.
  12. Remove the thermostat housing.
  13. Remove both rocker arm covers.
  14. Remove the lower intake manifold bolts. Make sure the washers on the four center bolts are installed in their original locations.
When removing the valve train components they should be kept in order for installation the original locations.
  1. Remove the rocker arm retaining nuts or bolts and extract the rocker arms and pushrods.
  2. Remove the intake manifold from the engine. Remove and discard the gasket.
  3. Using a suitable scraper, clean gasket material from all mating surfaces. Remove all excess RTV sealant from front and rear ridges of cylinder block
To install:
  1. Place a 0.12 inch (3mm) bead of RTV, on each ridge, where the front and rear of the intake manifold contact the block.
  2. Using a new gasket, place the intake manifold on the engine.
  3. Install the pushrods in their original locations. Coat the pushrods with prelube.
The intake pushrods are marked yellow (5 3 /4 inch long) and the exhaust are green (6 inches long). Make sure the pushrods are properly seated in the valve lifters and rocker arms.
  1. Position the rocker arms in there original locations and tighten to specifications. Refer to the procedure earlier in this section.
  2. Install lower the intake manifold attaching bolts. Apply sealant 12345739 (or equivalent thread locking compound) to the threads of bolts. Tighten the vertical bolts first then the diagonal bolts to 115 inch lbs. (13 Nm).
  3. Install the front rocker arm cover.
  4. Install the thermostat housing.
  5. Connect the upper radiator hose to the thermostat housing.
  6. Fasten the coolant inlet pipe to thermostat housing.
  7. Connect coolant bypass pipe at the water pump and cylinder head.
  8. Install the power steering pump in the mounting bracket.
  9. Loosely install the serpentine belt.
  10. Connect the right side engine mount.
  11. Remove the special engine support tool.
  12. Fasten the fuel lines to fuel rail and bracket.
  13. Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).
  14. Install the MAP sensor.
  15. Connect the upper engine wiring harness connectors to the related components removed earlier.
  16. Connect the vacuum lines to the PCV, vacuum modulator and fuel pressure regulator.
  17. Install the EVAP canister purge solenoid and ignition assembly.
  18. Install the alternator assembly.
  19. Connect the power steering line to the alternator bracket.
  20. Install the serpentine belt.
  21. Connect the spark plug wires to the spark plugs and intake plenum wire retainer.
  22. Install the EGR pipe to the exhaust manifold.
  23. Attach the control cables to the throttle body lever and upper intake plenum mounting bracket.
  24. Install air intake assembly and top half of the air cleaner assembly.
  25. Install the brake vacuum pipe.
  26. Fill the cooling system.
  27. Connect the negative battery cable, then start the vehicle and verify that there are no leaks.

For PARTS REPLACEMENT check in THIS LINK: carpartswholesale.com

Hope helps.

Feb 01, 2011 | 1994 Pontiac Grand Am

1 Answer

Where is the thermostat located on a 1995 toyota spacia 2.2 ltr auto?


The termostat is easy to locate on any car. What you need to do is look for the TOP radiator hose and follow it back to the engine block. Where it ends you will see this hose clamped to an inlet pipe which is bolted to the engine's intake manifold. Remove the two bolts that hold this inlet pipe in place and there you will find the thermostat.

Please remember to rate my solution. Thanks!

Jan 26, 2011 | Toyota Passenger Cars & Trucks

1 Answer

Need to remove the water pump


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


WATER PUMP REMOVAL
  1. REMOVE RH ENGINE UNDER COVER
  2. DRAIN ENGINE COOLANT
  3. REMOVE GENERATOR (See page CH-8)
91329747


  1. REMOVE INTAKE MANIFOLD STAY
  1. REMOVE WATER INLET PIPE
(a) Disconnect the following hoses: 91329748


(1) Water inlet hose (2) Heater inlet hose (3) Water bypass hose 91329749


(b) Remove the bolt, water inlet pipe and 0-ring.
  1. REMOVE OIL DIPSTICK GUIDE AND GENERATOR ADJUSTING BAR
(a) Remove the oil dipstick. (b) Remove the mounting bolt of the dipstick guide clamp and generator adjusting bar. 91329750


(c) Pull out the dipstick guide. Plug the guide installation hole of the oil pump. (d) Remove the 0-ring from the dipstick guide. 91329751


  1. REMOVE WATER PUMP
    • Remove the bolt, 2 nuts and water pump.

Jan 02, 2011 | 1992 Toyota Tercel

3 Answers

Where is the thermostat located in a 2001 toyota sienna?


Welcome to FIxYa.com



THERMOSTAT REMOVAL

HINT: Removal of the thermostat would have an adverse

effect causing a lowering of cooling efficiency. Do not remove

the thermostat, even if the engine tends to overheat.

1. DRAIN ENGINE COOLANT

2. REMOVE AIR CLEANER CAP WITH AIR CLEANER

HOSE

3. DISCONNECT ECT SW1TCH CONNECTORS

4. DISCONNECT ENGINE VIRE PROTECTOR FROM

WATER INLET AND RH CYLINDER HEAD

Remove the 2 nuts, and disconnect the engine wire

protector from the water inlet and cylinder head.

5. DISCONNECT WATER INLET PIPE FROM WATER

INLET AND LH CYLINDER HEAD

a) Remove the bolt and disconnect the inlet pipe from the

water inlet.

b) Remove the O-ring from the inlet pip e.

6. REMOVE WATER INLET AND THERMOSTAT

a) Remove the 3 nuts, water inlet and thermostat.

b) Remove the gasket from the thermostat.

INSPECTION

INSPECT THERMOSTAT

HINT: The thermostat is numbered with the valve opening

temperature.

a) immerse the thermostat in water and gradually heat the

water.

b) Check the valve opening temperature.

Valve opening temperature: 80 - 84CC (176- 183 deg f)

If the valve opening temperature is not as specified,

replace the thermostat.

c) Check the valve lift.

Valve lift: 10.0 mm (0.394 inch) or more at 95CC (203 deg f)

If the valve lift is not as specified, replace the

thermostatleedavidian_93.jpgleedavidian_92.jpg.

d) Check that the valve is fully closed when the

thermostat is at low temperatures (below 40CC (104CF)).

if not dosed, replace the thermostat.

INSTALLATION

1. PLACE THERMOSTAT IN WATER PUMP

a) Install a new gasket on to the thermostat.

b) Align the thermostat jiggle valve with the upper stud

bolt and insert the thermostat in the water inlet

housing.

HINT: The jiggle valve maybe set within 15 deg of either

side of the prescribed position.

2. INSTALL WATER INLET

Install the water inlet with the 3 nuts.

Torque: 8.0 Nm (80 kgf-cm, 69 inch lbs.)

3. INSTALL WATER INLET PIPE

a) Install a new O-ring to the water inlet pipe.

leedavidian_91.jpgleedavidian_90.jpgleedavidian_89.jpgleedavidian_88.jpgleedavidian_87.jpgleedavidian_86.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Dec 06, 2010 | 2001 Toyota Sienna

1 Answer

My 2005 Grand Prix has no heat and my gas mileage is awful. would changing thermostat fix problem. also at night not sure if this has anything to do with problem only my blue temperature arrows light...


A FAULTY THERMOSTAT STUCK OPEN WILL EFFECT GAS MILEAGE AND CAUSE POOR OR NO HEAT CONDITIONS.THERMOSTAT NOT A HARD JOB TO FIX.ALL YOU NEED TO DO IS DRAIN OUT SOME OF THE COOLANT IN A DRAIN PAN.DRAIN COOLANT LEVEL BELOW THERMOSTAT.IF YOU HAVE 3.8L ENGINE THERMOSTAT HOUSING ON TOP INTAKE MANIFOLD.IF YOU HAVE 5.3L ENGINE FOLLOW TOP RADIATOR HOSE IT WILL LEAD YOU TO THERMOSTAT HOUSING.REMOVE HOUSING THERMOSTAT INSIDE THE HOUSING.IF YOU HAVE WATER INLET ANDTHERMOSTAT IN ONE COMPLETE UNIT OR HOUSING YOU HAVE TO REPLACE THE ENTIRE WATER INLET HOUSING WITH NEW THERMOSTAT.THIS TYPE UNIT WILL HAVE LONG PIPE WITH BYPASS PIPE WITH WATER INLET WITH THERMOSTAT. ONCE YOU REPLACE THERMOSTAT.IF YOUR RED ARROWS OFF AND HEAT STILL DONT WORK THE DEALERSHIP WILL HAVE TO CHECK IT OUT.WITH NEW THERMOSTAT AND PRESSURE CAP.MAKE SURE GET COOLANT LEVEL CORRECT.SEE HOW HEAT WORKS.IF NOT YOU HAVE A ELECTRICAL PROBLEM AT AC AND HEATER CONTROL SWITCH.

Dec 03, 2010 | 2005 Pontiac Grand Prix

2 Answers

I'm in the process of replacing the thermostat on my 2003 freelander. finally got the coolant drained......that was fun. everything is disconnected and all intake plenum bolts removed( 4 small in the...


You will have to remove the intake manifold (this is the solid large plastic cover that covers the top of the engine when you remove the engine cover). There are many wires and small vacuum hoses to disconnect. Plus.., when re-installing, it is a common problem the manifold cracks if excessive torque is applied to the fastening bolts. And you probably should relpace the intake manifold gasket.You can then remove the thermostat assembly by disconnecting the hoses and loosening the mounting screw.

----------

The procedure as per service manual is as follows:----

Following the Service Manual instructions, drain the coolant circuit, then remove the return pipe and the short rubber hose connected to the engine main coolant rail (1 clip at the bottom + 1 clip at the top). You remove also the outlet hose (1 clip at the engine outlet spout + 1 clip at the bottom pipe, you need to loosen the pipe mount to remove the hose). Once removed the return pipe you can undo the coolant rail: 2 (tight) bolts below the rail and the oil dipstick bolt holding the thermostat housing. Doing this without the manifold in place is simple, but its not that easy with the manifold on.... once loosened the coolant rail you can remove the thermostat housing. You open it (3 bolts) and replace the old thermostat with new. All 3 gaskets should be replaced, to minimize the risk of leaks. Apply silicone lubricant on the O-rings, then fit housing + coolant rail back in.

----------

This will help you.Thanks.Helpmech.



Nov 16, 2010 | 2003 Land Rover Freelander

1 Answer

How to get to rear spark plugs


requires removing your intake manifold. Time consuming and delicate as the intake is plastic. Make sure to cover the intake plenum holes to prevent objects from falling in.

Aug 31, 2010 | 2006 Toyota Sienna

1 Answer

How do you access the rear spark plugs on a 2006 toyota sienna?


remove the intake plenum you should check youre spark plug type if they are iridium there is no need to replace them unless you are over 120k miles

Feb 24, 2010 | 2006 Toyota Sienna

1 Answer

Valve covers gasket leak oil


To replace the valve cover gaskets on a Sienna: The front one is easy. The difficult one is the other side, closest to the firewall. You will need to purchase a new intake plenum gasket, when you buy the new valve cover gaskets, because you MUST remove the intake plenum to remove the rear valve cover. You can NOT get the back side valve cover off of the engine without removing the plenum. Trust me.
Hope this helps, and thanks for choosing FixYa.

Nov 04, 2008 | 2001 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...