Question about 1992 Ford Tempo

Open Question

Remove rear bumper

I would like information on how to remove the rear bumper. I cannot afford a mechanic.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: Rear Bumper Cover

you would need to heat it up from behind to remove the dent and the rubbing compound should work as long as it hasnt penetrated your paint layer

Posted on Jun 07, 2008

Ad
  • 12 Answers

SOURCE: How to Remove the Rear Bumper - BA Fairmont/Falcon

Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Posted on Aug 22, 2009

michigan man
  • 3533 Answers

SOURCE: I have a 2002 Ford Taurus and we need to replace

for the most part you only need a screwdriver and a pair needle nose pliers try these websites www.alldatadiy.com also www.taurusclub.com wish you the best of luck Michigan Man.

Posted on Oct 11, 2009

mikehitchner
  • 28 Answers

SOURCE: how difficult is it to remove the rear bumper on a Ford Explorer

its not the bumper

Posted on Jan 01, 2010

  • 92 Answers

SOURCE: I have a 2006 Ford Explorer and 2 of my park aid

You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

2 Answers

How to remove 2008 toyota yaris rear bumper


Go to this site. http://www.yarisworld.com/forums/showthread.php?t=33767

Further down you will see a diagram of the bumper removal.

remove the two bolts under the hatch, the four plugs along the bottom edge, and the plate light. Don't forget the red circle clip or bolt on the diagram. Then you just pull it off.

Nov 30, 2011 | Toyota Cars & Trucks

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

2 Answers

Does anyone know how to replace an Echo Rear Bumper?


Look inside the trunk you will find the bolts under some groomets, get under rear fenders and remove the plasitc covers and remove the bolts for the sides and you will remove it.

Jul 09, 2009 | 2004 Toyota ECHO

1 Answer

How do you replace rear bumper cover on 2009 Honda Civic


Should look for the bumper shocks and remove which ever is easiest, remove bumper then remove cover , replace cover and reinstall bumper, watch out for wires and clips might hold cover to side plastic.

May 24, 2017 | 2009 Honda Civic

1 Answer

Rear bumper replacement


there will be some screws and plastic clips around the trunk and rear quarters remove these. look at yours should still see the screws to give you an idea

Nov 06, 2008 | 1994 Geo Prizm

Not finding what you are looking for?
1992 Ford Tempo Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...