Question about 2006 Nissan X-Trail 2.2

Open Question

Nissan x trail knocking noise when changing gear

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4044 Answers

SOURCE: knocking/tapping when accelerating on 2003 nissan

Usually an indication of Bad fuel, needs a tune up or Slipped Timing. Most likely bad fuel or tune up depending on when the last time you replaced the plugs and wires was. If you have been using the 87 Octane low grade fuel that would cause this or if you happened to get some bad fuel at a station. The vehicle will run on 87 octane but was designed to have a minimum of 89 octane fuel, the mid grade. If you haven't replaced your spark plugs in the last 25,000 miles replace the spark plugs and wires. If you suspect the fuel is the issue you can get injector cleaner or Octane boost and add to a FULL tank of gas to clean it out.

Posted on Oct 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knocking noise from rear end


If car is rear wheel drive.....Check you Universal joints on your driveshaft

Could also be Trailing Arm bushings.if you have coil Springs on your rear axle. These bushings keep the axle from rotating. So when you do that Clutch jumpy thing the axle is trying to rotate and with bad bushings it could be 'banging'

Sep 10, 2015 | Cars & Trucks

1 Answer

Knocking noise front on both side when standing dead still at robot and holding in the break on both sides at the lights


This fault is a bit srange, when you apply the brake pedal you here a
"Knocking" noise from the front of the car, alternating from one side to the other, the cause of this is a bad earth in the rear light clusters,
which results in the headlight motors activating "Jumping" thus causing the noise, solution is to clean the conections and conecting
blocks of the rear light clusters in extreme cases change the rear light clusters but a good cleaning should fix it hope this was helpfull

May 31, 2014 | 2011 Nissan Micra 1.2

1 Answer

Making knocking sound


A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 06, 2013 | Nissan Cars & Trucks

1 Answer

Nissan x Trail I have 2003 Nissan X Trail 2.2


check power steering pump valves as the noise could be valve vibration from weak control springs
timing chains do not rattle it properly adjusted and the so called rattle could be the injectors/ needles operating correctly

Apr 18, 2017 | Nissan Cars & Trucks

1 Answer

Knocking sound from the front of my manual 1999 nissian altima


need to determine if its engine or drive train see if the noise stays when you coast or is it in the transmission could be anything from a gear issue to clutch issue may be a driveline issue noise coming from your wheels you need to find the general location of the noise then you can center the issue

Sep 18, 2012 | 1999 Nissan Altima

1 Answer

I have a 99 mustang gt & I know it needs either a pilot bearing or throwout bearing, but it started making a knocking noise when the car reaches @ 2200 rpm & stops after I shift gears! Does not...


your description is not clear. the throwout and pilot bearing only work when the pedal is depressed. and dont make knocking noises, so rule that out. If the noise is when the car is moving and in gear, the trans maybe bad. makes noise in all gears at 2200 rpm? trans needs to come apart.

Sep 14, 2011 | 1999 Ford Mustang Cobra

2 Answers

The engine has a nkockig sound..could this be caused by a bad knock sensor?


No it isnt a knock sensor the knock sensor job is to detect a knock noise and ****** timing. The knock that it is looking for is from octane or fuel or pinging that creates N0X s. A pollution gas. The knocking noise that you are hearing is different. If it is a multiple noise ar a rattling sound that will be the valves. There are other noises like a piston knock this knock is a sharp metallic noise, If the knock occurs only on acceleration that noise is a crankshaft noise. You need to check you oil level and make sure it is corrects. Look at the oil condition do you see silverish or whitish condition,is the oil deep black.

Apr 24, 2011 | 2004 Nissan Maxima

1 Answer

Engine has a knocking noise when acelerating from a complete stop.


If is does it if you rev the engine in park it may have a bad engine. If only in gear it may have a bad drive axle which is making noise.

May 06, 2010 | 2004 Nissan Murano

1 Answer

1997 Nissan Quest knock sensor and transmission


A knock sensor going is usually indicated by pinging/rattling noise from engine especially when accelerating up a hill or just giving throttle but not kicking down a gear. Not sure what your asking about transmission?

Apr 07, 2009 | 1999 Infiniti.5 QX4

Not finding what you are looking for?
2006 Nissan X-Trail 2.2 Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...