Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: serpentine belt diagram:
The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.
Posted on Jul 18, 2008
I go to the local parts store & buy a repair book for the vehicle for approx. $20, read the procedure in the book, gather the tools & parts required, replace the belt per the instructions
Posted on Oct 11, 2009
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
Posted on Jan 22, 2010
My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.
I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.
CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
For the 1991 Dodge Grand Caravan:
Posted on Mar 07, 2010
Testimonial: "thanks for your help it was along time ago and forgot to let you know thank you so much "
Click on the following free direct Link.
It has the correct Belt Diagrams for your 1992 Dodge Grand Caravan wirh either the 3.0L SOHC V6 or the 3.3L V6.
Included on the Diagrams are the Instructions on "Rotating" the Automatic Tensioner. See Below for additional Instructions to make your job easier.
"HOW TO": I professionally prefer the Serpentine Tensioner Tool.
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s).
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening located on the Tensioner Arm) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.
Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Before You GO:
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!
Posted on Apr 12, 2010
Tips for a great answer:
Apr 24, 2017 | Dodge Cars & Trucks
Sep 21, 2016 | 2013 Dodge Dart
Dec 19, 2015 | Cars & Trucks
Feb 18, 2015 | Dodge Cars & Trucks
Nov 02, 2014 | Dodge Dart Cars & Trucks
Sep 28, 2014 | Dodge Dart Cars & Trucks
Jul 03, 2014 | 2010 Kia Forte
202 people viewed this question
Usually answered in minutes!