Question about 1998 Ford Explorer

1 Answer

Tqping in the motor


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 818 Answers

Tapping noise probably valve lifters- denny

Posted on Dec 31, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace the timing belt on a 1988 Buick Lesabre 3800 engine.

It has a Timing chain an gears, not a belt > an you would need to pull the front part of the motor apart , serpentine belt ,alternator possibly , harmonic balancer , timing cover , plus drain the cooling system first . If your have no done this before I suggest you take it to a professional , These are know for the cam gear wearing the teeth off , the metal gets all inside the engine - bearings an everything ! I had one I did an after getting it running , found out it bent a valve . The lady was driving it at a good speed an it stopped running , left on the side of the road . She had it towed to the shop , an she couldn't me if she heard any strange noises when it happened . Her's was an 80's Oldsmobile with the same engine ,thinking about it now I should have told her it wasn't worth the money to do it .

Aug 17, 2015 | Buick Cars & Trucks

1 Answer


It's your lifters they need to be tighten They are under the valve covers

Dec 31, 2013 | 1998 Ford Explorer

1 Answer

Automatic seat belt on drivers side will not move. belt drive motor will not turn off. where can I disable the drive motor?

we just discussed this one. You need to tape one of the limit switches closed. Also, remove small plastic cover on rear trim panel to expose thumbwheel for emergency use.

Aug 09, 2010 | 1993 Mercury Villager

1 Answer

Engine stalled at about 30 miles hour now i have been told by garage it broke timing belt

If you really did break a timing belt while driving at 30 MPH, you would have also heard a lot of bad noises coming from the engine and are looking at a large repair bill to repair engine damage.

Mar 21, 2010 | 1996 Chevrolet Cavalier

2 Answers

Engine sound when speeding up

the problem you are describing sounds like you have a loose rod bearing which is common on a engine with that many miles on it and under excelleration yes!! it will knock with it knocking to that degree for any lenght of time! putting new bearing in won;t fix it!! cause damage to the cracnshaft has already arose you will need to pull the motor and change the crank and bearings or replace the motor

Jan 18, 2010 | 2000 Toyota ECHO

1 Answer

Seat belts receivers are taped over

First step is to remove the tape, no way to know the process of a mad man better then to dive into his world. Just make sure no one is sitting in them when you try to connect the male to the female end, perhaps they got stuck which could be a reason they were taped over. Start with that and report back.

Nov 17, 2009 | 1993 Jaguar Xj Series

2 Answers

I have a 1989 chevy cavalier z24 2.8 6 cyl. Hard to start

a serpentine belt will not cause any such problems and the shop that told you the motor was bad probably can't figure out the problem and figured aww what the heck just replace the whole motor at your expense.... an even easier way to check the motor is with a compression tester you can rent from an auto parts store they cost about $50-$100 us to purchase new if you can't rent one I suggest getting a repair manual at that auto parts store as well @$30 take a couple of hours to read through I am not to familiar with that particular model but I wanna say there is an air temp sensor located on the air intake line or the intake manifold itself prob. a $12 sensor if you feel like taking a shot in the dark

Apr 26, 2009 | 1989 Chevrolet Cavalier

1 Answer

92 geo metro crankshaft sensor

I HAVE A 1996 gEO mETRO. and i had the same problem. I was driving and out of no where the car shut off. and it would not start....
i was told it was the cam censor. that's in the distributer... my total cost for the part was around 200 from NAPA. Labor about 32....
sorry my fist language is Italian so forgive my spelling

Mar 02, 2009 | 1996 Geo Metro

1 Answer

Starting problems

can be a lot of reasons 1.battery 2.oil level 3.timing belt 4.starter motor most of cars are having problem of starter motor nd you can check it if fuel pump is working or not take of the outlet fuel pipe and try to start it if fuel is coming means is ok if not then it means fuel pump

Aug 13, 2008 | 1999 Ford Contour

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides