Question about Nissan Minivan

1 Answer

How much lbs to tighten cylinder head bolts zd30

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

65 to 70 lbs thanks stephen

Posted on Jan 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 916 Answers

SOURCE: tightening head

New Headbolts are recommended

Long bolts are torqued to 46'lbs + 90 degrees.

Short bolts are torqued 43'lbs + 90 degrees.

Start in the center, and work to the edges, torquing the bolts in two stages.

Rockers are torqued to 22'lbs.

Posted on Dec 21, 2008

stevenhurc
  • 450 Answers

SOURCE: torque specifications cylinders head bolts

for 1.5/1.6L DOHC, 18 Ft-lbs + 70deg + 70deg + 50deg

for 1.8/2.0L DOHC, 18Ft-lbs +90deg + 90deg +90deg

Posted on Jun 24, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

ZJLimited
  • 17970 Answers

SOURCE: Head tourqe specs for 403 olds and bolt tightening

Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Posted on Mar 29, 2010

Testimonial: "Every thing I was looking for Thanks a lot"

  • 335 Answers

SOURCE: cylinder head bolt torque chevrolet 3.4

here is the troque spec for the cylinder heads.

Cylinder Head Bolt

  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cylinder head tighten torque


Have a look on this link. You may be able to find your car:

SPECIFICATION LOOKUPS

Cylinder head bolts are usually tightened to around 65 ft-lbs, depending on what the car is.

There's more than 4 cylinder head bolts... There's usually 10 bolts.
There's also a sequence for tightening the bolts:

cylinder head tightening order Google Search

When tightening cylinder head bolts do it in 'stages' and follow the sequence .. ie.. tighten the bolts finger tight first, then torque them up to about 25 ft-lbs. Wait 2 minutes.

Then tighten them to about 45 ft-lbs in sequence. Wait 2 minutes.

Do it again up to about 55 ft-lbs. Wait 2 minutes.

Tighten them up to 65 ft-lbs or whatever is recommended for your car.

Tightening in order/sequence pulls the cylinder head evenly onto the block. Waiting 2 minutes between stages allows a 'stretched' bolt to 'settle'.

Feb 17, 2016 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

2 Answers

I need the torque for all the head bolts on my 1983 datsun 280zx


Check this information for 1983 Datsun 280ZX 2.8L (click over image for zoom)...

zjlimited_2038.jpg

Fig. 7: Cylinder head bolt removal sequence


zjlimited_2039.jpg

Fig. 13: Head bolt torquing sequence-1970-83 models

After repair job, temporarily install and tighten the two center (right and left) cylinder head bolts to 14 ft. lbs. (18 Nm).

Install the camshaft sprocket together with the timing chain onto the camshaft. Make sure that the marks made earlier, line up. If the chain will not stretch over the sprocket, the problem lies in the tensioner. Refer to the Timing Chain removal and installation procedure for the timing procedure, if necessary.

Install the cylinder head bolts. Note that two lengths are used. Tighten the bolts in sequence.
1970-71 models:
Tighten the bolts to 33 ft. lbs. (43 Nm)
Tighten the bolts to 47 ft. lbs. (61 Nm)

1972 models:
Tighten the bolts to 47 ft. lbs. (61 Nm)
Tighten the bolts to 55 ft. lbs. (71 Nm)

1973-83 models:
Tighten the bolts to 30 ft. lbs. (39 Nm)
Tighten the bolts to 44 ft. lbs. (57 Nm)
Tighten the bolts to 54-61 ft. lbs. (70-79 Nm)

To complete the installation, reverse the removal procedures. Adjust the valves to a preliminary COLD clearance of 0.2mm for the intake and 0.25mm for the exhaust. Operate the engine until it is at normal operating temperature, retighten the head bolts (loosen them slightly and retighten to the final torque figure) and adjust the valves to the HOT clearance specifications.

Hope this helps; remember to rating this answer and leave some testimonial comment about this.

Oct 13, 2011 | 1983 Nissan 280ZX

1 Answer

I am looking for the head bolt torque specifications and sequence for a 1988 jeep Cherokee 4.0 i6


zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Mar 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Torque specs for cylinder heads 4.9 v8 engine (NOT NORTHSTAR) cadillac.


5850a5e.jpg

Fig. Cylinder head torque sequence-4.5L and 4.9L engines (not Nothstar, this is 4.6L)

  1. Tighten cylinder head bolts, in sequence, to 38 ft. lbs. (50 Nm).
  2. Tighten cylinder head bolts, in sequence, to 68 ft. lbs. (90 Nm).
  3. Tighten No. 1, 3 and 4 cylinder head bolts to 90 ft. lbs. (120 Nm).

Hope this helps (remember rated).

Aug 12, 2010 | 1991 Cadillac Eldorado

1 Answer

I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:
  • Do not reuse the old cylinder head bolts.

May 31, 2010 | 2004 Kia Rio

1 Answer

I need the head bolt torque specification for a 2005 aveo


install:
  1. The cylinder head should be cleaned and inspected prior to installation.
  2. Lightly oil all bolt and stud bolt threads before installation.
  3. Clean all gasket mating surfaces thoroughly.
  4. Install a new head gasket on the cylinder block. WARNING Always use new cylinder head bolts when installing the cylinder head or damage to the engine may occur.
  5. Install the cylinder head on the cylinder block.
  6. Tighten the cylinder head bolts in reverse of the removal sequence. Tighten the 2004 cylinder head bolts to 18 ft. lbs. (25 Nm). Tighten an additional 70°, plus 70°, plus another 50°. Tighten 2005 bolts to 18 ft. lbs. (25 Nm). Tighten an additional 60°, plus 60°, plus another 10°.
  7. Install the right engine mount. Tighten the engine mount attaching bolts to 22 ft. lbs. (30 Nm).
  8. Install or connect the following:
    • Intake manifold
    • Intake manifold support bracket. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Throttle cable
    • Surge tank coolant hose
    • Heater hose to cylinder head
    • Fuel feed line at the fuel rail
    • All vacuum hoses
    • Exhaust manifold
    • Rear timing belt cover
    • Timing belt tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Idler pulley. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Intake and exhaust camshaft gears. Tighten the bolts to 49 ft. lbs. (68 Nm).
  9. Apply a small amount of gasket sealant to the corners of the front camshaft caps and the top of the rear camshaft cover-to-cylinder head seal.
  10. Install the valve cover using a new gasket
  11. Align the timing marks on the camshaft gears.
  12. Align the mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.
  13. Install the timing belt and rotate the water pump clockwise to apply tension to the timing belt.
  14. Tighten the water pump bolts to 89 inch lbs. (10 Nm).
  15. Adjust the timing belt tension.
  16. Install or connect the following:
    • Spark plug wires
    • Upper and lower timing belt coversCrankshaft pulley. Tighten the bolt to 70 ft. lbs. (95 Nm), plus an additional 30°, then another 15°.
    • Accessory drive belt
    • Air cleaner housing
    • Radiator hoses
    • Front splash shield
    • Right front wheel
    • Coolant temperature sensor
    • Fuel feed line from fuel rail
    • IAT sensor
    • Intake manifold pressure sensor
    • DIS coil connector
    • Fuel injector connectors
    • ECM ground terminal
    • Negative battery cable
  17. Fill the engine with oil and coolant.
  18. Start the engine and check for leak0900c1528009e8b5.jpg

Apr 02, 2010 | 2005 Chevrolet Aveo

1 Answer

I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003


Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

Jan 24, 2010 | 2003 Chrysler Town & Country

1 Answer

What is the torque settings on the head bolts for 2002 nissan x-terra 2.4litre?


① Step 1: 22 ft. lbs. Step 2: 59 ft. lbs. Step 3: Loosen completely then retorque to 22 ft. lbs. Step 4: 18-25 ft. lbs. Step 5: Plus 86-91 degrees ② 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs. ③ The cylinder heads and the lower intake manifold are installed together Step 1: Tighten the cylinder head bolts to 22 ft. lbs. Step 2: Tighten the cylinder head bolts to 43 ft. lbs. Step 3: Loosen the cylinder head bolts completely Step 4: Tighten the cylinder head bolts to 84 inch lbs. Step 5: Tighten the intake manifold fasteners to 35 inch lbs. Step 6: Tighten the intake manifold fasteners to 13 ft. lbs. Step 7: Tighten the intake manifold fasteners to 12-14 ft. lbs. Step 8: Loosen all intake manifold fasteners completely Step 9: Tighten the cylinder head bolts to 22 ft. lbs. Step 10: Tighten the cylinder head bolts 60-65 degrees Step 11: Tighten the cylinder head sub-bolts to 80-105 inch lbs. Step 12: Tighten the intake manifold fasteners to 35 inch lbs. Step 13: Tighten the intake manifold fasteners to 78 inch lbs. Step 14: Tighten the intake manifold fasteners to 70-84 inch lbs. ④ 10-12 ft. lbs. +60-65 degrees ⑤ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 75 degrees clockwise Step 5: Plus 75 degrees clockwise ⑥ Step 1: bolts 11-22 19 ft. lbs. Step 2: bolts 1-10 29 ft. lbs. Step 3: bolts 1-10 Plus 60-65 degrees ⑦ Step 1: 20 ft. lbs. Step 2: loosen to 0 ft. lbs. Step 3: 14 ft. lbs. Step 4: Plus 85-95 degrees ⑧ Step 1: 31 ft. lbs. Step 2: Plus 60 degrees ⑨ 83 inch lbs. ⑩ Stud bolt: 11 ft. lbs. Nuts: 31 ft. lbs. ⑪ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 90 degrees clockwise Step 5: Plus 90 degrees clockwise ⑫ Bolts: 17-24 (M8) 16 ft. lbs. Install rear main seal Bolts: 1-16 (M10) 26 ft. lbs. Bolts: 1-16 (M10) Plus 90 degrees clockwise ⑬ Step 1: 33 ft. lbs. Step 2: Plus 84-90 degrees clockwise ⑭ Intake manifold collector: Bolts and nuts: 8 ft. lbs. Stud bolts: 61 inch lbs. ⑮ Intake manifold: Bolts and nuts: 5 ft. lbs. and than to 21 ft. lbs. Studs: 8 ft. lbs.

Jan 10, 2010 | 2002 Nissan Xterra

1 Answer

What are the torque settings for the cylinder head 2000 subaru forester


This procedure is for the SOHC only.

E: INSTALLATION
1. CYLINDER HEAD

  1. Install cylinder head and gaskets on cylinder block. CAUTION: Use new cylinder head gaskets.
  2. Tighten cylinder head bolts.
  1. Apply a coat of engine oil to washers and bolt threads.
  2. Tighten all bolts to 29 Nm (3.0 kg-m, 22 ft. lbs.) in alphabetical sequence. Then tighten all bolts to 69 Nm (7.0 kg-m, 51 ft. lbs.) in alphabetical sequence.
  3. Back off all bolts by 180° first; back them off by 180° again.
  4. Tighten bolts (a) and (b) to 34 Nm (3.5 kg-m, 25 ft. lbs.) .
  5. Tighten bolts (c), (d), (e) and (f) to 15 Nm (1.5 kg-m, 11 ft. lbs.) .
  6. Tighten all bolts by 80 to 90° in alphabetical sequence. CAUTION: Do not tighten bolts more than 90°.



  1. Further tighten all bolts by 80 to 90° in alphabetical sequence shown in figure provided. CAUTION: Ensure that the total "re-tightening angle" [in the former two steps], do not exceed 180°.

May 24, 2008 | 2000 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...