Question about 2003 Audi A4 Cabriolet

1 Answer

A4 1.8 02 plate - fault code p01297 - runnung poor

I have an Audi A4 1.8 on 02 plate and fault code p01297 is stored. Cars not running properly.We've changed coil packs, dipstick and fuel pressure valve but faults still there. can you help?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

Code P1297(Connection turbocharger - throttle valve pressure hose) is related to air delivery to the engine. Unfortunately there is many components that could caused this code. For 1.8 engine the most common places to look for:
Check for damaged vacuum lines, next check over-bust valve(located in the intake hose) if holding vacuum, than I would check intake hose itself for damage or leaks. Some times broken throttle body can cause that fault (idle fluctuation). Lastly if car lack of power- damaged turbocharger can cause insufficient intake pressure.

Posted on May 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 1994 Lumina 3.1 at low rpm it run bad but high rpm it run good


Check PCV valve and all vacuum hoses. Check EGR valve fot proper operation.

Apr 25, 2017 | Chevrolet Lumina Cars & Trucks

1 Answer

90 camaro 3.1 V6 barely runs , I have replaced the Fuel pump Dist,S plugs and wires any suggestions?


Hello Johnny,

When you say barely runs..please elaborate. Does the vehicle start okay? idle poorly? run poorly under throttle? Please describe the symptoms of how your Camaro is barley running.

The first thing to do is check your instrument panel for a SERVICE ENGINE SOON light and then have the fault codes read at your local parts store...(some retail outlets provide this service free of charge.)

Fault codes will point you in the right direction. Add to your post for assistance... if required.

Jun 04, 2016 | 1990 Chevrolet Camaro

1 Answer

Audi A4, 58 plate, 2ltr, 211ps version, ecs and epc warning lights flickered and then came on together, engine running lumpily at low revs (<2000rpm), any ideas anybody?


You need to take the car into the dealer or a well equipped repair shop and have the control module scanned for faults. This takes a very special tool, this is not the little $35 code readers that parts stores sell.

Jun 03, 2016 | 1998 Audi A4

1 Answer

1997 Audi a4. Replacing thermostat. Can't get the housing off due to Cam belt in the way. How do I remove the belt? It's not the belt that runs off the alternator. It's a wider belt. Not...


If you index the engine properly (put cylinder 3 at top dead center, verified by alignment of timing marks on cam sprockets and crank pulley) you can remove the belt safely - the cams won't spin. But to get the housing off, you can slide the belt forward on the cam sprocket without removing it. Do it carefully - I've slid them halfway off and had a friend hold it while I tapped the channeling plate downward and off to replace the thermostat. Then slide it back in place once the new thermostat is in and the plate is resecured in place.

Jun 18, 2011 | 1997 Audi A4

1 Answer

Esp light on all the time glow plug light


could be faulty relay, a scan for fault codes should reveal problem

May 29, 2010 | 2004 Audi A4

1 Answer

18034 code,i think is a bad conection, in the TCM,but where is it.my car is a audi a4 2005


Trouble code identification:
VAG type 5-digit fault code 18034 = EOBD type P1626 fault code:
Fault location = CAN data bus, TCM - no signal
Probable cause = TCM trouble code(s) stored, TCM incorrectly coded, wiring, matching resistor in ECM.

Jan 28, 2010 | 2005 Audi A4

2 Answers

Air bag light keeps coming on in ford focus 03 plate zetec 1.6 wa


Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Apr 08, 2009 | 2003 Ford Focus

Not finding what you are looking for?
2003 Audi A4 Cabriolet Logo

1,192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...