Question about Bentley Continental GT

Open Question

Change battery key fob - Continental GT Bentley Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: key fob will not undo

If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.

Posted on Oct 16, 2008

  • 1 Answer

SOURCE: renault megane key fob wont work

I had the same problem with mine

your key fob is now out of sync with the ECU to sync them just follow this link (renault will charge up to £180 for new key and to sync it)

http://renaulthelp.110mb.com/ImmBypass.html

Posted on Jan 09, 2009

emissionwiz
  • 75051 Answers

SOURCE: key fob not working after battery change ford focus 2006

Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

Posted on May 28, 2009

polarcycle
  • 1392 Answers

SOURCE: reprogram 2005 Dodge Durango key fob

Go to the dealer. It is the only way, they have to use a computer. Changing the battery doesn't make it lose it's program though. You most likely broke the battery hold down. This is the most common thing I see at my shop. If the key still starts the vehicle, you now have a bad key fob. If not, you may be able to get it reprogrammed.

Posted on Aug 05, 2009

  • 1 Answer

SOURCE: Key fob won't unlock or lock car VW Golf 2000

my mum had a similar problem and it turn out the code the key transmits to the engine had gone wrong she took it to a vw dealer and they reprogrammed the key. it works fine now and is a common problem. hope that helps

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed battery on my key fob and it won't work


What is year--make--model?
The key fob is a transmitter so there has to be a receiver in the vehicle. At the moment, I can't tell if problem with transmitter or receiver? Can you try a different key fob? Where applicable, if key fob needs to be programmed, maybe the info is in your owners manual?

Apr 10, 2016 | Cars & Trucks

1 Answer

How to change battery on 2012 key fob


I use a small flat ***** driver just to pry open the fob. Then I just pull it apart, it will separate in 2 parts. Change the battery and just snap on the 2 parts back together.

Jun 29, 2014 | 2011 Dodge Journey

1 Answer

My immobilizer does not recognise my key fob


Put key in ignition.
Press unlock button on key fob.
Immobilizer should now recognize it, if it was original fob but car or fob battery was changed or is now low.

Saabs are particular about batteries that are otherwise good, but just below 12 volts.

Mar 29, 2014 | 2005 Saab 9-3 1.8

1 Answer

My key will not start my car,then it wouldn't open the door


This model year comes equipped with Keyless Enter-N-Go, which uses an electronic transmitter in the key fob to communicate with the car. The vehicle's doors will not unlock and the vehicle will not start if the key fob is not matched to the vehicle or if the commonly-available watch battery in the key fob has been depleted. The EVIC will flash a message upon vehicle startup if it determines that the battery in your key fob is low on charge and should be replaced.

To open the doors, try the following:

1. Use the spare key fob that came with the vehicle. If the battery in your main key fob is depleted, the spare key fob's battery may still retain charge due to its much more occasional use.

2. The key fob comes with an emergency key inside of it. To remove the emergency key, slide the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. This key will allow you to unlock the driver's side door and glove compartment. It will not start the vehicle.

To start the car with a severely-depleted key fob battery, try the following:

1. In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back-up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.

To replace the battery in your key fob, try the following:

1. Remove the emergency key from the key fob following the directions above.

2. Using a vinyl spudger tool or a flat-bladed screwdriver, gently pry the two halves of the key fob apart at the indented slot above the slot for the emergency key.

3. Replace the depleted battery with a new battery. Use the depleted battery to visually match the size. The battery is usually available wherever watch or hearing-aid batteries are sold.

4. Snap the key fob back together and replace the emergency key. If the issue is a depleted battery, your key fob should operate normally.

If the issue is not related to the state of the battery, you will probably need to contact your local dealer for service.

Source: Owner's Manual, pages 12-17

http://justgivemethedamnmanual.com/dodge/dodge-charger-owners-manual/

Mar 01, 2014 | 2011 Dodge Charger

1 Answer

I changed my car battery, now my 2008 Nissan Altima key fob won't work


There is a special procedure involved in keying your fob to your car once the battery has been changed. You must lock and open the door with your key. Turn the ignition to "on"(not start) then push the fob's open and close button, then shut off ignition. This procedure is done everything the key battery is changed. Hope this can help you!
------------
Motorcycle Diagnostic Scanner

Oct 31, 2012 | Cars & Trucks

3 Answers

New Dodge Journey 2011 Where would the key enclosed in keyfob fit to start the vehicle if remote not working?


I just changed the battery in my fob for 2011 Journey Crew, with the battery removed ( from fob ) I did start my car by pushing the start button whith my fob... so the theory is tested and true.... also the battery you'll need is CR2032 available everywhere... and removing the battery will NOT remove the programming of your fob ( also tested )... so no need to visit the "steelership" Hope this helps....

Apr 03, 2011 | 2011 Dodge Journey

1 Answer

How do I change battery in my lr3 key fob


You do not change the battery as it is re-chargeable. It is charged in the key fob unit while it is in the car's ignition and while you are driving the vehicle.

If you have a spare key that has low battery power then it needs to be used in the vehicle to charge the battery.

If you have been using the key fob and it has suddenly failed this is probably due to a faulty circuit board. You will need to replace the key fob with a new one from the dealer. It needs to be programmed for your car by the dealer.

Always have a spare key for this vehicle and keep the battery charged by using it occasionally.

Dec 17, 2010 | 2006 Land Rover LR3

4 Answers

My 2006 cadillac sts key fob all of a sudden is not working it says no fob detected and i have the fob what can b wrong??


Some late model fobs contain electronics beyond the push buttons.
Batteries are replaceable...small screws may let you do this.
If the battery is not the cause....a replacement fob may be expensive. A road service technician can probably troubleshoot and replace cheaper than dealer !

Sep 07, 2010 | 2006 Cadillac STS

1 Answer

Reprogram 2005 Dodge Durango key fob


Go to the dealer. It is the only way, they have to use a computer. Changing the battery doesn't make it lose it's program though. You most likely broke the battery hold down. This is the most common thing I see at my shop. If the key still starts the vehicle, you now have a bad key fob. If not, you may be able to get it reprogrammed.

Aug 05, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bentley Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Are you a Bentley Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...