Question about 1986 Volkswagen Jetta

1 Answer

A/C on again off again

My a/c will run fine if I bypass the switch and go power direct. I don't know if it's the relay if so which one or is it the on/off switch on dash. The fuse is good.It was working fine then it started this on when it wants to.now its not engaging the clutch. 1986 jetta diesel 5 speed shift. Thank You

Posted by on

  • Shoaib Rais
    Shoaib Rais May 11, 2010

    if u bypass power on/off switch and go direct then it works fine that means the ON off swtich is faulty u can change it

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Ok Thank You.. Turns out to be a spade connection under hood was corroded and needed a good cleaning.. Works fine now ..again, thank you , Jerry

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 montero fuel pump relays


Fuel pump relays are designed to trigger the power from using the power system of the vehicle to a direct battery power connection. Relays save the sensitive power used accessories by not robbing the power from them and bypassing them to use the power right from the battery source.

For example, if a relay was not used for the pump, it would lower the idle on your car everytime it turned on. Having a relay allows the pump to run and not steal valuable voltage from the cars system. These fuel relays are also a safety device in case of a car accident. The car has shock sensors that react in a car accident and shut the fuel pumps off through the relays so the occupants do not burn in an accident. If these continued to run after an accident and fuel continued to be pumped at a high pressure rate, you can imagine what the consequences might be.

Relays make the route to the battery to run the item, more direct. Bypassing the cars needed power to run the vehicle.

Jul 12, 2014 | 1999 Mitsubishi Montero Sport

2 Answers

Who know how to bypass coolent fan Thanks


it's not easy but it can be done, need a relay with harness and some wire. you must tap into the fan wire(positeve 12v) and run it to the switch side of the relay tap power(12v) constant to the relay and also a switch(12v) source and a ground ok it sounds hard but hre's a diagram 29968290-87b0-4ec1-8bba-df60277f7b84.gif
good luck

Jun 07, 2014 | 1997 Dodge Caravan

1 Answer

Installed new blower motor. bearing shelled in old one. new motor won't blow. tested . it's good don't have power to moter. fuses good relay good. isthere a circuit breaker in wiring for b


I don't have a diagram for a 2008. On 2005 models the blower motor relay gets power from a 30amp fuse.
When the blower switch is in the high position the resistor is bypassed and power flows directly to the motor. The motor is grounded to the car.
The fan relay also gets power from a 7.5amp fuse and is controlled by the HVAC control on the dash.
Do you have power into and out of the relay?

Feb 25, 2013 | 2008 Mitsubishi Lancer

1 Answer

2000 rodeo will not crank checked fuel pump and relays they are good .When I bypass relay it runs fine anyone know whats wrong


Sounds like the relay isn't receiving it's signal power to close and activate the main power to the fuel pump. Test to make sure it's getting the power when you first turn on the key [ The PCM will turn it off after a few seconds if it dosen't sense a imput from the Crank Sensor that the engine is running ]. If there's no power there, first look for a blown fuse and make sure there's power to the fuse, if not then you will have to test back thru the circuit to find the cause [ also check the igntion switch].

Jun 24, 2011 | 2000 Isuzu Rodeo

1 Answer

My 91 jeep wrangler 4.0 will shut down all power at all speeds from idle to driving on the interstate. I jumped out the auto shutdown relay and it works fine but i cannot find the auto shutdown switch to...


There is no switch. The relay gets a signal from the computer. If there is no signal from the crank position sensor the computer will not close the relay. If it runs with the relay bypassed, chances are good that the relay itself is bad.

Feb 06, 2011 | Jeep Wrangler Cars & Trucks

2 Answers

Have no spark and fual pump has no power going to it


check the anti-rollover switch in the trunk, either side and reset it like a breaker.

Jun 20, 2010 | 1997 Ford Escort

1 Answer

Car won't start,can't hear fuel pump come on when i cycle key.how do i know if it's the pump or maybe a relay.


the only way is to "bypass the relay" if there is power at the relay and you feed power directly to the pump and it has a good ground and it does not work, then the pump is bad. sometimes if you feed it power directly,(by pass the relay) whack the bottom of the tank, if you hear it start to run, then the pump is bad.

Oct 12, 2009 | 1999 Chrysler Cirrus

2 Answers

Overheating at idle


That's because cadillac replaced it with an upgraded switch. to find out if your relay is bad bypass the relay and directly jump the fans to find out if the fans still work. if you don' know how to do this find a friend that does.

Jul 05, 2009 | 1999 Cadillac DeVille

1 Answer

1987 nissan pulsar


Question is, does fuel pump relay come in/ go out when ignition switched on? How do you know "no power source to fuel pump", was that because bypassing the relay didn't cause it to run? Or did you check for supply to the pump and find nothing doing?.
Sounds rather like a frozen pump to me... or a blown fuse??

May 28, 2008 | 1989 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...