Question about Cars & Trucks

1 Answer

Will not start p2045 p2197 p0190 p2247 p2245 p2248 p2249 p2518 comes up

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,710 Answers

Code p2045 refers to reductant temperature sensor--high input==causes --wiring faulty sensor
code p2197 refers to heated oxygen sensor(HO2S)1 bank 2-- signal stuck lean===causes HO2S---fuel pressure---injectors---intake leak
also refers to oxygen sensor (O2s)1 bank 2 -signal stuck lean===causes--O2S--fuel pressure---injectors---intake leak
also refers to heated oxygen sensor (HO2S) 1 bank 2--implausible signal===causes wiring---short to ground--short to positive--HO2S---ECM
code po190 refers to fuel rail pressure (FRP) sensor-circuit malfunction===causes --wiring ---fuel rail pressure sensor---ECM
code p2247 refers to heated oxygen sensor (HO2s) 1 bank 1 reference voltage--open circuit===causes--wiring ---ho2s
also refers to o2s 1 bank 2 reference voltage ---open circuit===causes wiring---o2s
also refers to HO2S 1 bank 2 ---no signal===causes wiring--ho2s---ECM
code p2245 refers to HO2S 1 bank 1 --reference voltage --circuit low===causes--wiring short to ground--ho2s also refers to o2s 1 bank 1 circuit low===causes wiring short to ground--o2s
code p2248 refers to the ho2s I bank --performance problem===causes --wiring--ho2s
code p2249 has the same causes short to ground---ho2s and o2s
code p2518 refers to a/c refrigerant pressure sensor B ---circuit high===causes wiring short to positive--a/c refrigerant pressure sensor.
so after all that replace all the ho2s and o2s sensors using the correct tools so that the wiring is not damaged and check the wiring back to the ECM for burns and rub marks.

Posted on Dec 31, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Forward to a skate 2006 V6 engine code P0190


no it will not ,it may blow the big ends but it will not throw any code ,this code you quoted does not exist in my ford code list but on the universal OBDII


P0190 Fuel Rail Pressure Sensor Circuit Malfunction

could be a loose sensor?? or a dirty connection on the plug?

Dec 06, 2014 | 2006 Ford Escape

1 Answer

2005 dodge sprinter p0053 p0130 p0131 p2238 p2245 problems


These can actually have TWO o2 sensors (Lambda)
Normally one pre Cat and on Post Cat (Cat - Catalytic converter)
You will have one on the headers from the engine. then you may also have one after the Cat.

Check if you also have the second, as this may the one at fault.

Apr 03, 2014 | Dodge Sprinter Cars & Trucks

1 Answer

Code p2197


disconnect the sensors cancel the codes start engine if the codes don't come back replace sensor

Mar 26, 2014 | 2005 Mazda MPV

1 Answer

P0190 fuel rail pressure sensor circuit


code p0190 refers to fuel pressure (FRP) sensor--circuit malfunction===causes---wiring---fuel rail pressure sensor--ECM
try replacing the sensor.

Dec 27, 2013 | Cars & Trucks

1 Answer

Code P2247


DTC P2247: Front A/F Sensor (Bank 2, Sensor 1) VCENT Line High Voltage

NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information.
Information marked with an asterisk (*) applies to the front bank (Bank 2).
Turn the ignition switch ON (II).
Clear the DTC with the HDS.
Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, then let it idle for 2 minutes .
Check for Temporary DTCs or DTCs with the HDS.
Is DTC P2243 and/or P2247* indicated?

YES - Go to step 5.

NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM.

Turn the ignition switch OFF.
Jump the SCS line with the HDS.
Disconnect the A/F sensor (Sensor 1) 8P connector.
Disconnect ECM/PCM connector B (24P).




Connect A/F sensor (Sensor 1) 8P connector terminal No. 8 to body ground with a jumper wire.




Check for continuity between ECM/PCM connector terminal B13 (B21)* and body ground.
Is there continuity?

YES - Go to step 11.

NO - Repair open in the wire between the ECM/PCM (B13 (B21)*) and the A/F sensor (Sensor 1), then go to step 15.

Remove the jumper wire from the A/F sensor (Sensor 1) 8P connector, then reconnect ECM/PCM connector B (24P).
Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, then let it idle for 2 minutes .




Measure voltage between ECM/PCM connector terminals B13 (B21)* and D10.
Is there about 0.2 V or less?

YES - Go to step 21.

NO - Go to step 14.

Replace the A/F sensor (Sensor 1).
Reconnect all connectors.
Turn the ignition switch ON (II).
Reset the ECM/PCM with the HDS.
Do the ECM/PCM idle learn procedure. See: Programming and Relearning
Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?

YES - If DTC P2243 and/or P2247* is indicated, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to Step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.

NO - Go to step 20.

Monitor the OBD STATUS for DTC P2243 and/or P2247* in the DTCs MENU with the HDS.
Does the screen indicate PASSED?

YES - Troubleshooting is complete.

NO - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 18 and recheck.

Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM.
Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?

YES - If DTC P2243 and/or P2247* is indicated, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.

NO - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM.

Jun 23, 2013 | 2006 Honda Odyssey

1 Answer

How to fix code p0190 on a 2000 mercury cougar, and where to find diagram to fix this problem


THE P0190 CODE IS CONCERNING THE FUEL RAIL PRESSURE SENSOR! THERE IS A MALFUNCTION THERE! A GOOD SOURCE FOR REPAIR IS: www.manualsonline.com

Mar 02, 2011 | 2000 Mercury Cougar

1 Answer

Code p0190


"P0190 Fuel Pressure Sensor 1"

Sep 28, 2009 | 2002 Mitsubishi Lancer

1 Answer

Max 2004 sprinter codes p2238 p2245 what is


p2238 is the oxygen sensor bank 1 sensor #1 which is up stream in the exhaust manifold. My manual is showing that the current control crcuit is low. p2245 is the same sensor, showing that voltage circuit is low. Replacing this sensor should fix the problem.

Mar 10, 2009 | 2004 Dodge Sprinter

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...