Question about 2004 Jeep Grand Cherokee Limited

1 Answer

Remove heater control panel - 2004 Jeep Grand Cherokee Limited

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Did your read the FSM on topic , HVAC? and Body chapters.
why not?

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Posted on Jan 06, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3G Mitsubishi Eclipse Climate Control Light Bulb Replacement


The control panel for the heater and A/C must be removed. Suggest you get Chilton's manual from the library. It will take you through step by step with pictures. To summarize: 1) Remove trim panel covering radio and heater controls. 2) Remove radio. 3) Disconnect the two heater control cables from the control panel. The trick to removing the cables is to compress the "claw" spring holding the cable by pressing a screwdriver from the underside of the control panel to release each cable.4) Remove control panel. Take to a workbench. From the backside of the control panel at the top, notice two large holes through which you can access the V2 Toshiba bulb holders. Turn them a quarter turn to remove them and the bulbs. The bulb is a common #74 bulb.

Apr 22, 2012 | 2001 Mitsubishi Eclipse

1 Answer

How to install a blower moter and fan


Well, here's the instructions from the service manual. The labor guide says this can be done in 1.6 hours...I don't see how, unless the instructions are wrong about having to remove the instrument panel. My thoughts are that if you are only doing the blower motor, the blower assembly will come out without pulling the dash. You probably only have to do a partial disassembly and remove the glove box and the glove box lower support.

*************************************************************************************

BLOWER ASSEMBLY

Removal and Installation

1. Disconnect battery ground cable. Remove Instrument panel. (See Instrument Panel Removal) Disconnect resistor connector. remove blower assembly duct. Disconnect motor connector. Remove blower assembly

2. Remove blower assembly screws and blower motor assembly. Remove clip and fan from assembly. Separate motor case and remove blower motor. To install, reverse removal procedure.



INSTRUMENT PANEL

Removal

1. Disable air bag system. See AIRBAG RESTRAINT SYSTEM article in ACCESSORIES/SAFETY EQUIPMENT SECTION. Disconnect negative battery cable. Scribe mating marks on steering wheel and shaft for installation reference. Using Steering Wheel Remover (J-29752) remove steering wheel. Remove steering cowl.

2. Remove instrument panel grilles and plug, or driving pattern indicator panel (A/T Models). Disconnect electrical connections. Remove instrument panel hood, instrument cluster ezel and instrument cluster. Remove hood release handle. Remove knee protector.

3. Remove dash fuse/relay block and side trim. Remove engine control module box. Remove radio console and glove box lower reinforcement. Remove speaker covers and glove box. Remove heater control panel knobs and cover. Disconnect heater control cables, and remove heater control panel. Remove illumination control knob. Remove instrument panel.

Installation

1. Install instrument panel. Install and adjust heater control cables. To complete installation, reverse removal procedure. Ensure mating marks on steering wheel and shaft align. Apply grease to contact ring and tighten steering wheel nut to 26 ft.lbs. (35 N.m).

Feb 28, 2011 | 1995 Isuzu Rodeo

2 Answers

How do i fix the heater core on my ford taurus 1995


Hi there,

Remove heater/evaporator case. Remove vacuum source line from heater core tube seal. Remove seal from heater core tubes.
Remove heater core access cover screws. Remove access cover and seal from heater/evaporator case. Lift heater core and case seals out of heater/evaporator case.
Installation
If installing new heater core, transfer case seals to new core. Install heater core and seals into heater/evaporator case. Install heater core access cover on case. Install seal on heater core tubes. To complete installation, reverse removal procedure. Evacuate and charge A/C system. Refill cooling system.

HEATER/EVAPORATOR CASE
Removal
  • Disconnect negative battery cable. Drain coolant from radiator. Gently pull instrument panel away from right side of dash panel.
  • Discharge A/C system using approved refrigerant recovery/recycling equipment. Disconnect heater hoses from heater core. Plug heater core tubes or drain coolant by blowing coolant from heater core using low pressure compressed air. Disconnect vacuum supply hose from inside engine compartment.
  • Disconnect A/C lines from evaporator core. Plug A/C lines and evaporator core tubes. Remove instrument panel assembly brace to evaporator case bracket screw. Remove assembly brace.
  • Remove floor register and rear floor duct from bottom of heater/evaporator case. Remove nuts securing heater/evaporator case to firewall. Remove 2 screws securing support brackets to cowl top panel. Carefully pull heater/evaporator case away from firewall. Remove heater/evaporator case.
  • To install, reverse removal procedure. Evacuate and charge A/C system. Refill cooling system.
INSTRUMENT PANEL
Removal & Installation
  • Position front wheels in straight-ahead position. Disable air bag system. See AIR BAG RESTRAINT SYSTEM article in ACCESSORIES/SAFETY EQUIPMENT section. Disconnect negative battery cable. Remove steering column trim shrouds.
  • Disconnect all electrical connections from steering column switches. Remove cover from under steering column. Remove 4 bolts and reinforcement from under steering column. Disconnect parking brake release control motor from parking brake and ignition switch connector.
  • Disengage insulator retainer. Remove insulator. Remove 4 nuts and reinforcement below steering column. Remove 4 nuts securing steering column to instrument panel and lower column to front seat. Disconnect PRNDL cable (A/T models).
  • Ensure ignition switch is locked to prevent steering column from turning. Remove 4 instrument cluster retaining screws. Disconnect speed control cable and vehicle speed sensor (if equipped). Disconnect electrical connectors and remove instrument cluster. At steering column opening, remove one bolt securing instrument panel to brace. Remove one instrument panel brace bolt (below radio area).
  • Remove sound insulator under glove box by removing 2 push nuts securing insulator to studs on climate control case. Remove glove box door and compartment. Remove air cleaner housing, battery and battery tray. Disconnect wires of main wire loom in engine compartment. Disengage rubber grommet from firewall. Feed wiring into passenger compartment through hole in firewall.
  • Remove right and left kick panels. Disconnect wires from instrument panel at right and left kick panel sides. Remove screws on left and right sides of instrument panel.
  • Pull up to unsnap right and left speaker opening covers. Remove speaker covers. Working through steering column and glove box openings, reach under instrument panel and disconnect electrical connectors, vacuum hoses, A/C-heater control panel cables, and radio antenna cable.
  • Support instrument panel. Remove 3 screws attaching top of instrument panel to cowl top. Disconnect remaining wires. Remove instrument panel. To install instrument panel, reverse removal procedure.

Hope this helps...

Jan 17, 2011 | 1995 Ford Taurus

1 Answer

Looking for where the heater cord is located?


To remove and installing the Heater Core, check this procedure...
  1. Disconnect and plug the heater hoses at the firewall.
  2. Disconnect the heater valve control cable.
  3. Remove the heater unit attaching nut on the firewall.
  4. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.
1. Remove the heater duct.

zjlimited_113.jpg

Fig. 1: Removing the heater duct assembly

  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.
zjlimited_114.jpg

Fig. 2: Removing the heater case assembly

zjlimited_115.jpg

Fig. 3: Removing the heater core from the heater case


Hope this helps (remember to rate this answer).

Nov 23, 2010 | 1992 Honda Civic

1 Answer

Fan blows, but heater display doesn't light up. blows out cold air only. no heat


Check fuses to the A/C or Heater Control Unit in the fuse box(es). IF none are blown, then may have to replace A/C-Heater Control Unit:

A/C-Heater Control Unit Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Center bezel from the instrument panel A/C-Heater Control chr_pacif_ac_htr_cntrl.gif

    • Three screws that secure the A/C-heater control to the instrument panel
    • A/C-heater control from the instrument panel
    • Two wire harness connectors from the control
To Install:
  1. Install or connect the following:
    • A/C-heater control to the instrument panel
    • Two wire harness connectors to the back of the A/C-heater control
    • A/C-heater control into the instrument panel
    • Three screws that secure the A/C-heater control to the instrument panel
      1. Torque to: 17 inch lbs. (2 Nm)
    • Negative battery cable and calibrate the A/C-heater control
prev.gif next.gifprev.gif

Nov 06, 2010 | 2005 Chrysler Pacifica

1 Answer

My heater blower was working on #3 setting but not any more so I think it may be the heater control switch. How can I get the face of the dash board off


Disconnect the battery ground lead.

  1. Remove the radio/cassette player and CD player (if fitted
  2. Remove the bezel with the heater/air conditioning control panel.
  3. Remove bezel with heater/air conditioning control panel .
Remove the heater/air conditioning control panel from the bezel
0214260.gif
19d9385.gif
e662ada.gif

you will need this tool shown below to remove the factory radio
af4e1b9.gif

Oct 18, 2010 | 2000 Ford Focus

2 Answers

There is coolant leaking on the passenger side underneath of the car and rear of engine. It doesn't seem to be the lower hose and both the rad and thermostat are new and appear to be dry. I suspect the...


agree, heater core. see procedure below


REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable and disable the SRS system (if equipped.)
WARNING All SRS wire harnesses are covered with a yellow insulation. Read the SRS precautions found in this section and install the short connectors as described.
  1. Properly drain the cooling system.
  2. Disconnect and plug the heater hoses at the firewall.
  3. Disconnect the heater valve control cable.
  4. Remove the heater unit attaching nut on the firewall.
  5. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.

  6. Remove the heater duct.
    177f070.gif

Fig. Fig. 1: Removing the heater duct assembly

  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.

07c9641.gif

Fig. Fig. 2: Removing the heater case assembly

82ed899.gif

Fig. Fig. 3: Removing the heater core from the heater case


To install:

  1. Install the heater core into the heater unit.
  2. Install the heater assembly and the attaching bolts.
  3. Install the heater duct and steering column bracket.
  4. Install the dashboard assembly. Tighten the mounting bolts until just snug.
  5. Raise and attach the steering column.
  6. Install the center upper panel.
  7. Connect the speedometer cable and install the instrument gauge assembly.
  8. Install the control head, radio and center panel.
  9. Install the side vent and face plate.
  10. Connect the ground cable at the right of the steering column and the power mirror switch wire connector.
  11. Connect the sunroof switch connector, if equipped.
  12. Connect wire connectors at fuse panel.
  13. Install the heater unit attaching nut on the firewall.
  14. Connect the heater valve control cable.
  15. Connect the heater hoses at the firewall.
  16. Connect the negative battery cable.
  17. Fill, bleed and leak check the cooling system.

Oct 05, 2010 | 1991 Honda Civic

1 Answer

Fixing heater core on Mercury Villager front one


go here for lots of help

http://groups.yahoo.com/group/villagerquest/

Heater Case Removal
  1. Drain the engine coolant. Refer to Section 03-03 for the procedure.
  2. Disconnect the battery ground cable (14301).
  3. Disconnect the heater water hoses (18472) from the heater core (18476) at the bulkhead.
  4. Remove the instrument panel lower center panel (04494). Refer to Section 01-12 for the removal procedure.
  5. Remove the glove compartment and LH instrument panel lower cover (044L97). Refer to Section 01-12 for the removal procedure.
  6. Remove the instrument panel ash receptacle (04810).
  7. Remove the two upper center instrument panel finish panel screws and the two lower center instrument panel finish panel screws.




  8. Remove the center instrument panel finish panel (044D70) and disconnect the cigar lighter socket and cigar lighter illumination lamp electrical connectors.
  9. Remove the four radio chassis bracket screws and pull the radio chassis (18806) and climate control assembly from the instrument panel (04320). Disconnect the radio chassis electrical connectors, the antenna lead, the three climate control electrical connectors and remove the radio chassis and climate control assembly.
  10. Remove the two heater outlet floor duct screws. Remove the heater outlet floor duct (18C433).




  11. Remove the four RH instrument panel lower reinforcement bolts and the RH instrument panel lower reinforcement (045F08), then the four LH instrument panel lower reinforcement and the LH instrument panel lower reinforcement.
  12. Remove the anti-lock brake control module (2B373). Refer to Section 06-09 for the removal procedure.
  13. If equipped, remove the speed control amplifier. Refer to Section 10-03 for the removal procedure.
  14. Remove the electronic door lock control processor (14B001). Refer to Section 01-14A for the removal procedure.
  15. Remove the passive restraint control module. Refer to Section 01-20B for the removal procedure.
  16. Remove the two center duct screws and remove the center duct (19D633).




  17. Remove the two ground wire bolts.
  18. Remove the three U-bracket-to-chassis nuts.




  19. Remove the four U-bracket bolts and remove the U-bracket.


  20. Remove the two RH and the two LH instrument panel bracket bolts and remove the instrument panel brackets (042C74).
  21. Remove the RH inner duct.
  22. Remove the LH inner duct.
  23. Remove the two accelerator pedal and shaft bolts and then the accelerator pedal and shaft (9725).
  24. Remove the accelerator pedal stop screw and then the accelerator pedal stop (9816).
  25. Remove the heater outlet duct screw and remove the heater outlet duct.
  26. Remove the temperature blend/panel bypass door actuator motor. Refer to the procedure in this section.
  27. Remove the panel/floor/defrost door actuator motor. Refer to the procedure in this section.
  28. Remove the three A/C evaporator register duct screws and remove the A/C evaporator register duct.
  29. NOTE: The A/C evaporator/blower motor assembly does not have to be removed in order to remove the heater assembly.

    Remove the four A/C evaporator/blower motor assembly screws to aid in the removal of the heater assembly.
  30. Remove the four heater assembly screws.
  31. Remove the heater assembly.

Sep 30, 2009 | 1996 Mercury Villager

2 Answers

How to replace heater core 93 honda del sol


Heater Core Honda Civic/CRX/del Sol 1984-1995 Repair Guide REMOVAL&INSTALLATION
See Figures 1, 2 and 3
REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable and disable the SRS system (if equipped.)
WARNING All SRS wire harnesses are covered with a yellow insulation. Read the SRS precautions found in this section and install the short connectors as described.
  1. Properly drain the cooling system.
  2. Disconnect and plug the heater hoses at the firewall.
  3. Disconnect the heater valve control cable.
  4. Remove the heater unit attaching nut on the firewall.
  5. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.
  6. Remove the heater duct.
0900c15280061a21.jpgFig. 1: Removing the heater duct assembly
  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.
0900c15280061a22.jpgFig. 2: Removing the heater case assembly 0900c15280061a23.jpgFig. 3: Removing the heater core from the heater caseTo install:
  1. Install the heater core into the heater unit.
  2. Install the heater assembly and the attaching bolts.
  3. Install the heater duct and steering column bracket.
  4. Install the dashboard assembly. Tighten the mounting bolts until just snug.
  5. Raise and attach the steering column.
  6. Install the center upper panel.
  7. Connect the speedometer cable and install the instrument gauge assembly.
  8. Install the control head, radio and center panel.
  9. Install the side vent and face plate.
  10. Connect the ground cable at the right of the steering column and the power mirror switch wire connector.
  11. Connect the sunroof switch connector, if equipped.
  12. Connect wire connectors at fuse panel.
  13. Install the heater unit attaching nut on the firewall.
  14. Connect the heater valve control cable.
  15. Connect the heater hoses at the firewall.
  16. Connect the negative battery cable.
  17. Fill, bleed and leak check the cooling system.

Sep 01, 2008 | 1996 Honda Accord

Not finding what you are looking for?
2004 Jeep Grand Cherokee Limited Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...