Question about Cars & Trucks

1 Answer

Please explain how to remove and replace cv joint on thd outer driver's side of a caddy vw

I have removed tthe part from the vehicle but cannot get the cv joint of the drivers side drive shaft. Can you explain how to remove it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: 1998 grand cherakee driver side cv joint removal

You can find instructions for doing this in any half decent manual. One thing they usually don't tell you is when removing the large axle nut on the end, it helps to put a spare tire on with no center cap and with the vehicle on the ground, break that nut free before starting the job. without air tools, it's next to impossible to remove it when jacked up.

Posted on Mar 10, 2009

  • 1 Answer

SOURCE: 1995 4wd mazda b series/cv joint/drivers side

HOW TO REMOVE WHEEL BEARING ON MAZDA PICKUP 1995 B3000

Posted on Apr 05, 2009

pippall
  • 1486 Answers

SOURCE: 02yukon i cannot get the cv joint out from the wheel/brake assem

Remove steering joint.Then bottom ball joint then you should be ok.

Posted on Jul 13, 2009

  • 1118 Answers

SOURCE: Front-left Outer CV Shaft Disconnected from inner-CV shaft

If memory serves me right the axel is bolted to a plate on the front differenchel and a large nut on the end that goes thru the hub bearing, if you take the whole shaft out( both ends) i see no problem running it temporary without it.

Posted on Jul 14, 2009

  • 381 Answers

SOURCE: Tri-pot joint housing stuck on driver side of 2000

I have had this problem many times. I have always had to take the clamp off the drive axle boot near the transmission and take it apart there. I have never been able to get one off that did not pop off easy even after I had the transmission out. You just have to reuse the part that is stuck on the transmission and get a new clamp to re clamp the drive axle together. If you have any more questions feel free to ask and Ill do my best to answer them.

Posted on Feb 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

.I have removed the end of drive shaft out of the hub[rhs] ,other end of shaft is still attached.will the cv joint come off the end of the shaft so i can fit the new boot?


Which vehicle are you working on?

Some of these CV-joints are designed with an outside circlip. An example of such a setup would be on an Opel/Vauxhall. On cars like these with an outside circlip it is possible, after cleaning the grease to actually see the circlip and with a good quality circlip pliers, it is possible to expand the circlip sufficiently to remove the outer CV- joint with a sharp tap while keeping circlip expanded all whilst the CV- joint is still attached to the vehicle on the inner side.

On other designed CV- joints the circlip sits on the inside of the CV joint. In other words you cannot see the circlip at all. If it is such a design then the compete CV- joint unfortunately has to be removed.

Why it has to be removed if it an inside designed circlip?

Well in most cases it requires a rather sharp tap of a rubberized hammer on the outer CV to remove it from the drive shaft. This is not possible whilst the CV-joint is attached as damage to inner CV flange is very likely.

Apr 22, 2015 | Cars & Trucks

1 Answer

Cv joints


Hi Thomas, I have not changed CV's on your type of vehicle, but can give you the path to follow. Here we go; Always work with someone to assist you. pepare four plastic bags for use later. With both front wheels on the ground remove any wheel covers fitted. In the center of the wheel you will see the shafts of the CV's. These are held in position with large nuts, either locked with a tab or sometimes with a locking washer and split pin. Unlock whichever system is used and loosen the nuts on the shafts. Loosen the wheel nuts, jack up the vehicle and place chassis stands to support the vehicle and the lower it onto the stands. Remove the wheels and remove the center nuts from the CV joints. If the vehicle is fitted with McPherson struts, loosen the two through bolts and nuts, or if fitted with wishbone suspension loosen and remove the bolts securing the the upper ball joints. Swing the stub axle outward and downwards so that there is enough room to remove the CV shafts from from the hubs. Put on a pair of goggles and then climb under the vehicle and release the boots or retaining bolts holding the shaft into the spyder or inner CV joint. Once removed pull the half shaft out of the housings keeping everything as clean as possible and wrap in a plastic bag.. (There will be high impact grease inside both the inner and outer joints, This may have been thrown out in the event that the rubber boots are broken) If you are replacing the entire half shafts, carefully observe the way in which the inner joint is fitted. If there are no bolts, studs or nuts holding a flange onto the gear box differential housing, the inner joints will be held in place by spring loaded clips fitted around the ends of the inner shafts. If your vehicle uses that type of fitting the shafts will be levered out. It will be important to use a catchment tray to collect any transmission oil which leaks out. Cover the joint with one of the plastic bags. If you are fitting only the outer CV's, the defective units are knocked off the shafts with a heavy copper mallet (The shafts also have locking cur clips holding the shafts in place. Sometimes the inner basket of the CV bearing housing will need to be cut or broken out, so the the joint can be removed. Please both you and your friend use safety goggles during this procedure. Once removed, fit the new joint. If you are replacing the entire assembly and if they are the type using clips, use a thick piece of wood and hold the shaft as straight as possible then ask your pal to knock the shaft into the housing. The rest of the job is the opposite to removal. When fitting the outer CV shaft nut follow the correct tightening torque setting, as these usually hold the front wheel bearings at the correct settings and tightness. Regards John

Feb 14, 2012 | 2006 Chrysler Pacifica

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

1997 Pathfinder How do you replace the left outer cv boot?


How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Mar 12, 2010 | 1997 Nissan Pathfinder

1 Answer

How to replace a CV joint 2000 Cavalier Drivers side


Buy the right CV axle. Raise right front of vehicle. Remove wheel. use a lugnut and washers to secure brake rotor so that it is not flopping and trapping rust behind. Remove axle nut. Loosen nuts from outer tie rod end stud and lower ball joint stud almost all the way off, but do not remove them completely. Seperate the studs from knuckles by striking each knuckle with a ball peen hammer. After the tie rod and lower ball joint are seperated from the spindle knuckles, pry down on lower control arm and push end of axle through hub toward transaxle until hub and spindle assembly is free from axle/CV joint. Place drain pan under transmission. Carefully place pry bar between innner CV joint and transmission and pop axle assembly loose. Install new axle in reverse of the dissassembly.

Feb 21, 2010 | 2000 Chevrolet Cavalier

2 Answers

Need to change cv outer boot on mazda ba 94 model.


it just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal
  1. Raise and support the vehicle.
  1. Remove the lug nuts (1012) and the front wheel and tire assembly.
  1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
  1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).




  1. Remove the front axle wheel hub retainer and discard it.
  1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.




  1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).




  1. Remove the ball joint bolt and the ball joint bolt nut.




  1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.




  1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.




  1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.

    Support the transaxle with a transaxle jack or equivalent.
  1. Remove the four transaxle mount-to-rear engine support nuts.




  1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
  1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.




  1. Position a drain pan under the transaxle.
  1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
    Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).




  1. Remove the front wheel driveshaft and joint.




  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
    If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
  1. Remove and discard the driveshaft bearing retainer circlip (3Z498).

Oct 03, 2009 | 1994 Mazda 323

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...