Question about 2004 Honda Civic

1 Answer

Tappet clearance for 2004 honda civic vtis - 2004 Honda Civic

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

2.0L only. 7 engines listed in fsm
intake= 0.0012-
exhaust= 0.0022- all below 100F.

but>>. that was just a wild guess on engine.......

no engine stated, Gen7 Civic non Hybrid?
no country stated, diffr, countries get diffr engines....!
in USA open hood, now look up, under hood see EPA sticker and Engine type stated.
lots and lots of engines, in 2004 they introduced the K- series
i-VTEC? S or SI>?
DOHC engine
here they all are. K20A" but which one? A1? Z3? what>?
http://en.wikipedia.org/wiki/Honda_K_engine


ok now ill pretend the car is USA, car.
i log in to alldata.com
i look and it has listing for 2.0L
and here is the text

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. Disconnect the negative battery cable.
  2. Note the radio security code and the radio presets.
  3. that means record them now. pen to paper.
  4. Remove the cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
  5. Set the number one piston at TDC. The punch mark on the variable timing control (VTC) actuator and the punch mark on the exhaust camshaft sprocket should be at the top. Align the TDC marks on the VTC actuator and exhaust camshaft sprocket.
  6. Using the proper gauge feeler gauge, adjust the valves on cylinder number one.
  7. Rotate the crankshaft 180 degrees. Using the proper gauge feeler gauge, adjust the valves on cylinder number three.
  8. Rotate the crankshaft 180 degrees. Using the proper gauge feeler gauge, adjust the valves on cylinder number four.
  9. Rotate the crankshaft 180 degrees. Using the proper gauge feeler gauge, adjust the valves on cylinder number two.
  10. Install the cylinder head cover.
  11. As required, on 2001-05 vehicles, reprogram the ECM engine idle characteristics. Be sure all electrical items are OFF.
  12. Start the engine. Hold the idle speed at 3000 RPM's in neutral until the radiator fan comes on or the temperature reached 194 degrees.
  13. Let the engine idle for about five minutes with the throttle fully closed.
  14. If the radiator fan comes on during the five minutes, do not count this toward the five minute programming time.
  15. Set the clock.
  16. As required, reprogram the power window control unit as follows.
  17. Turn the ignition switch ON. Lower the window, all the way down. Open the driver's side door.
  18. Turn the ignition switch OFF. Push and hold the drivers window DOWN switch. Turn the ignition switch ON. Release the driver's window DOWN switch. This must be done within five seconds.
  19. Repeat the above step three more times. Wait one second.
  20. Confirm that the AUTO UP and AUTO DOWN do not work. If they work repeat the procedure, paying close attention to the five second time limit
  21. Move the driver's window all the way down by holding the drivers window DOWN switch to the AUTO DOWN position.
  22. Pull up and hold the driver's window UP switch to the AUTO UP position until the window reaches the fully closed position. Hold the switch for one second.
  23. Confirm that the power window master switch has been reset by using the driver's window AUTO UP and DOWN function.
  24. If the AUTO UP and DOWN feature is still not working, repeat the complete procedure, paying close attention to the five second time limit.








Posted on Dec 30, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 117 Answers

SOURCE: tappet settings

depends on the engine

Posted on Jul 01, 2008

Trendy-Bee
  • 156 Answers

SOURCE: thermostat honda civic 2004

Visit http://www.autopartswarehouse.com/sku/Honda/Civic/OES_Genuine/Thermostat/2004/

Posted on Jan 02, 2010

alicantecoli
  • 22156 Answers

SOURCE: what is the tappet clearance on a honda accord

if manual adjustable tappets then 12 inlet and 15th exhaust will suffice but isnt this vehicle fitted wth hydraulic adjusting tappets??

Posted on Jun 15, 2010

  • 4 Answers

SOURCE: my car wont move forward or reverse

Chances are is that the torque converter needs to be replaced. However, the transmssion on this vehicle are only serviceable by transmision shops. No regular mechanic will open up the transmission. When the torque converter fails (clutch and plates shutters to small pieces) the debri flows in the transmision thereby potentially destroying the gears and/or clogging the filter and pump. Go straight to a reputable transmission shop and let them correctly diagnose the transmission.

Posted on Jul 26, 2010

jturcotte
  • 8266 Answers

SOURCE: Can you please give me

Do you mean 1.7L? I do not see a 1.6L in the manual. Instructions from autozone.com are pasted below.

lash:

Intake, 0.007-0.009 in (0.18-0.22mm).

Exhaust, 0.009-0.011 in. (0.23-0.27mm)

Civic
1.7L Engine

NOTE Adjust valves only when the cylinder head temperature is less than 100 degrees F.

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. Disconnect the negative battery cable.
  2. Note the radio security code and the radio presets.
  3. Remove the ignition coil cover. Remove the ignition coils. Remove the throttle cable clamps and harness holder from the cylinder head cover.
  4. Remove the cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
  5. Remove the grommet from the upper cover and disconnect the camshaft position (CMO) sensor connector. Remove the upper cover.
  6. Set the number one piston at TDC. The UP mark on the camshaft pulley should be at the top, and the TDC marks on the pulley should line up with the top edge of the cylinder head.
  7. Using the proper gauge feeler gauge, adjust the valves on cylinder number one.
  8. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the exhaust side of the cylinder head.
  9. Using the proper gauge feeler gauge, adjust the valves on cylinder number three.
  10. Rotate the crankshaft 180 degrees counterclockwise and bring the number four piston to TDC.
  11. Using the proper gauge feeler gauge, adjust the valves on cylinder number four.
  12. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the intake side of the cylinder head.
  13. Using the proper gauge feeler gauge, adjust the valves on cylinder number two.
  14. Install the cylinder head cover.
  15. As required, reprogram the ECM/PCM engine idle characteristics. Be sure all electrical items are OFF.
  16. Start the engine. Hold the idle speed at 3000 RPM-s in park or neutral until the radiator fan comes on or the temperature reached 194 degrees.
  17. Let the engine idle for about five minutes with the throttle fully closed.
  18. If the radiator fan comes on during the five minutes, do not count this toward the five minute programming time.
  19. Set the clock.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust the tappet clearances on a 2004 honda accord?


need to know what motor you have if its overhead cam then there is none if its a pushrod engine try going to autozone library ,its all free

Feb 25, 2015 | 2004 Honda Accord Tourer

1 Answer

Tappet clearance


posted 102 times.
here is 103
http://hondatech.info/downloads/Auto/Manuals/Civic/

there are huge numbers of engines used.
the first job is to learn what yours is.
do the cam belt before you bend the valves (hint)
lash is a side order dish to belt swap... fact.! at 60kmiles

Aug 24, 2013 | 1991 Honda Civic

1 Answer

Valve settings


- Pull the hand brake and put transmission in neutral.
- Remove spark plug cords.
- Remove the spark plugs.
- Remove the Tappet cover
- Lift up the left front wheel.
Cylinder number 1 is toward the pulleys and belts side.
- Rotate the crankshaft anticlockwise with socket and extension rod and bring the valve tappets (intake and exhaust) No. 4 cylinder on dancing position.
NOTE: THERE ARE OTHER WAYS ALSO TO ADJUST THE FOUR VALVES AT A TIME. BUT AS DIY FOLLOW THE FOLLOWING METHOD TO AVOID ANY CONFUSION.
- Adjust the valve clearance of number 1 cylinder.
Valve clearance:
Intake 0.18 - 0.22 (cold) Exhaust 0.25 - 0.28 (cold)
- Rotate the crankshaft anticlockwise to bring the valves of cylinder 2 on dancing position and adjust the valves of No. 3 cylinder.
- Similarly rotate the crankshaft to bring the valves of No. 1 cylinder on dancing position and adjust the valves of No. 4.
- Rotate the crankshaft anticlockwise to bring the valves of cylinder No. 3 on dancing position and adjust the valve clearance of No. 2 cylinder.

May 04, 2013 | 1999 Honda Civic

1 Answer

What are the intake and exhaust valve tappet clearance specs. of a honda civic 1999 1.6 liter vtec sohc engine?


Valve clearance Inches Millimeters
Intake 0.006-0.007 0.15 - 0.19
Exhaust 0.007-0.008 0.17 - 0.21

Apr 08, 2011 | Honda Civic Cars & Trucks

1 Answer

What is the valve tappet clearance specs. of a honda civic 1999 1.6 liter vtec sohc engine?


Intake: 0.007-0.009 in. (0.18-0.22mm) Exhaust: 0.009-0.011 in. (0.23-0.27mm)

Apr 08, 2011 | Honda Civic Cars & Trucks

2 Answers

Valve tappet clearance of toyota 7k engine and honda civic vtec engine 1.6


7k clearances are ( HOT ) Inlet 0.008 in ( 0.20 mm )
Exhaust 0.012 in ( 0.30mm)

Mar 24, 2010 | 2000 Suzuki Aerio

1 Answer

My car wont move forward or reverse


Chances are is that the torque converter needs to be replaced. However, the transmssion on this vehicle are only serviceable by transmision shops. No regular mechanic will open up the transmission. When the torque converter fails (clutch and plates shutters to small pieces) the debri flows in the transmision thereby potentially destroying the gears and/or clogging the filter and pump. Go straight to a reputable transmission shop and let them correctly diagnose the transmission.

Nov 22, 2009 | 2002 Honda Civic

1 Answer

I have a 2004 Civic (automatic) that makes a clicking/rattling sound when I'm idling. Goes away when I shift to Park from Drive. Any ideas what this might be from? At first I thought it was the fan/a/c,...


Clean air and fuel filter. Check the spark plugs for corrosion or debris.
If the above does not eliminate the problem, I suspect that the tappets need to be replaced.
Tappets are located above the piston and can wear out if air filter is damaged. Even a slight edge wear can make the car rattle in idle mode.
Even if only one tappet is faulty, all have to be replaced. Usually the cost is mainly of the parts; service costs are only a small fraction. Visit your local repair service.

Oct 20, 2009 | 2004 Honda Civic

2 Answers

TAPPET SETTINGS HONDA PRELUDE 2.2 IMPORT


Intake valve clearance 0.15mm-0.19mm (6-7 thou); Exhaust clearance 0.17mm-0.21mm (7-8 thou). All measurments COLD engine. 2.2 VTEC Prelude engine 1992-1996, import and UK.

Feb 22, 2009 | 1994 Honda Prelude

1 Answer

Tappet settings


depends on the engine

Jun 30, 2008 | 1995 Honda Civic

Not finding what you are looking for?
2004 Honda Civic Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...