Question about 2000 Mitsubishi Eclipse

1 Answer

Vibrates when brakes are applied

Cant get my front rotors off, removed brakes , but cant get the rotors off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Oil around the studs and hub with wd40 and let it soak. Then smack the living hell out of it. If you break the rotor it was warped anyway and they aren't that expensive. The best place to smack is between the studs, but be careful not to hit them.

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Severe wheel wobble when braking on steep decents


It is not wheel wobble but vibration from the front brakes. The front brake rotors have worn unevenly (known as disc thickness variation - DTV) and when this occurs you will get vibration from the front rotors as you apply the brakes and it is especially noticeable when braking on down hill runs. DTV is usually caused by poor alignment of the rotors on the hub. In other words sloppy installation procedures.

You will need to replace both the rotors and brake pads on the front and make sure the business that does the work properly checks the rotor for run out.


Disc Thickness Variation DTV Issue 14 Bendix Brakes

DTV Disc Thickness Variation Disc Brakes Australia

==============================================

Feb 21, 2016 | Cars & Trucks

4 Answers

Steering wheel shakes at high speed when brakes are applied


This is caused by the front disk brake rotors being warped from heat and running out of true, the wobble of the warped rotors causes the wheel to shake when you apply the brakes, it is worse the higher the speed you apply them at. Have the front rotors machined flat again or just replace them.

Mar 16, 2011 | 1998 Toyota Camry

1 Answer

My car camry 2003 runs well usually but sometimes the car trembles or gives trembling noise when the brake is applied.


will try to help.your front brakes and rotors may need replacement. when you apply brakes say,at 40 mph do you feel vibration on brake pedal or shaking in steering wheel? the vibration comes from worn or warped front brake rotors. while you have those rotors replaced,go ahead and have new front brakes applied also,or else you'll still have brake problems.always ask to see old parts when you have brakes and rotors unless you have a complety trustable mechanic! the rotors will be round and silver,a very bad brake rotor will have grooves cut in it.always shop for best price at different shops to get a picture of the price for replacement! do not be afraid to ask questions! front brake pads can cost anywhere fron $20.00 to $45.00 rotors can cost $40.00 to $50.00 each there will only be 2 rotors on the front and the brakes are complete for the front,both sides,on the front. as a general rule you'll replace your front brakes twice before you'll need to replace the back brakes because most of you stopping power comes from the front brakes. and as always,if you need further assistance please contact an expert!thank you for choosing fixya.com

Dec 21, 2010 | Toyota Camry Cars & Trucks

1 Answer

2006 Satrun Vue, experiencing a vibration wehn brakes are applied and then when brakes released a bit of vibration is felt at take of as well. The front rotors were replaced and turned since we have owned...


I would check the rear brakes drums, they may need to be turned. The front rotors may have warped again, with turning the rotors, it removes metal from the rotor which leaves the rotor with less metal to dissipate heat, and the rotor will warp again when they get hot.

Nov 27, 2010 | 2006 Saturn Vue

1 Answer

My 2003 expedition EB vibrates when applying brakes


the front rotors are warped ahd either need to be turned or replaced. use quality parts and motorcraft pads. if you use cheap rotors, they stand the chance of either being warped upon install or warping soon after.

Nov 08, 2009 | 2003 Ford Expedition

1 Answer

Had bad vibration in front end of car when brakes applied,installed new rotors and pads,still have slight vibration when brakes applied.


do u feel the vibration in the steering wheel or in the seat,i bet the most vibration was coming out of the front brakes and a little out of the rear brakes,u might want to change the rear brakes if the vibration is still annoying,also were the front wheels torqued to spec when installed?? if not u might end up with warped front brakes again,hope this helped

Sep 05, 2009 | 2003 Cadillac Deville

2 Answers

Vibration changed all four rotors,new pads.cant get vibration to stop


most likely you have a problem with your calipers and how they are gripping with abs assist control on rotor.

Jul 26, 2009 | 2005 Nissan Quest

1 Answer

2002 axiom front brakes vibrates when applied


Check your front and rear caliper slides for sticking,it sounds like one may be stuck.

Jul 19, 2009 | 2002 Isuzu Axiom

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

Front end vibrates when brakes are applied


Sounds like the rotors are warped,Were they checked during brake replacement?

May 14, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...