Question about 2000 GMC Sonoma Extended Cab

1 Answer

How do i remove the transmission coolent lines from the transmission?

Very tight spot and looks like a special tool is needed. does transmission have to be lowered?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 3,103 Answers

I would say yes..the back crossmember needs lowered..and a special open wrench is used to remove the lines..fluid will bleed out of them also..

Posted on Dec 30, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Murphybanton
  • 2004 Answers

SOURCE: do i need any special tools to change upper an

No.

Cheers

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cooling transmision lines


Make sure that you use thee correct tools when removing the hose. Important to keep in mind that these lines seize up so you may need to heat the fittings.
When installing new line, good idea to use a little anti-seize and then top off transmission fluid with vehicle running and it has reached operating temperature.

Jun 17, 2017 | 2000 Buick Century

1 Answer

My transmission went on my 2001 Ford Windstar LX. The overdrive light was flashing on and off when I was driving it on the highway and when I came to a stop steam was coming out of the engine compartment....


Steven, The trans cooling lines run from the transmission to the radiator tank. This cools the trans fluid. Making new lines is challenging and takes expierence and special tools. Usually the lines will break where a bracket holds the line to the engine or trans. Look for a rust spot or shinny spot rubbed on the line and that is most likely where the leak is. You may be able to buy this line already made but probabally only from the dealer.

Nov 16, 2010 | 2001 Ford Windstar

1 Answer

How do i take off the hard lines to the transmission


A special tool for releasing transmission lines is available from the local parts store. The plastic ones in a kit cost about $9. Don't attempt to remove the lines without those special line tools.

Aug 07, 2010 | 2001 Ford Taurus

1 Answer

Leaking o-ring in rear area of transmission. Leaving spots on garage floor dignosed as o- ring seal. How much trouble is to repair?


The o-ring is likely to be either on the Filler tube or on one of the transmission lines. Both are relatively simple to repair. The filler tube can be unbolted (usually one bolt) then carefully turned back and forth and pulled up until the bottom is exposed. Simple remove the old o-ring and install a new one then reinstall the tube and re-bolt. The transmission lines may use a special locking ring to hold them into place, you can rent a tool from you auto parts store to remove the line and replace the o-rings.

Jul 31, 2010 | 2005 Pontiac Grand Prix

1 Answer

Removal of transmission cooling lines from radiator. my repair manual says i need a special tool.


Yes, it's call a line disconnect tool, Napa has this tool part # 7759086 cost about $8.00.Also can be used for fuel filter line.

Jul 07, 2010 | 1997 Ford Taurus

1 Answer

How do i replace the transmission cooler


these cars have problems with trany oil leaks make sure thats the leak, most of the time its the lines, anyway it removes from under frt bumper area, remove the lines these are tight to get to,but once removed unbolt cooler and remove not a hard job just tight in some spots. hope this helps.

Dec 28, 2009 | 1996 Chrysler Cirrus

2 Answers

Need to replace gas filter but looks like i need a


This special tool is available at your local auto parts store. Ask your parts expert what size you will need. The tool is fitted around the fuel line and pushed into the fitting on the filter. Make sure you relieve the fuel system pressure before proceeding.

Oct 29, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Is there a special tool needed to change the serpentine belt


There is a special tool for removing your serpentine belt. It is a long thin bar designed to get in those tight spots. Most auto parts stores have these bars. Good luck. please rate my answer as a fixya!

Feb 16, 2009 | 2003 Toyota RAV4

1 Answer

Removing tranny lines from radiaor


on some fords a special tool is required to remove the lines. but it is not expenzive

Dec 08, 2008 | 1997 Ford Windstar

1 Answer

Transmission oil lines leaking


The lines have holes in them? Or are they just leaking at the connections? If just the connections, then all you need is two wrenches of the correct size. One on the permanent fixture nut like the radiator or the transmission, and the other wrench goes on the line. After removal, clean the threads, and apply some teflon tape and reassemble. tight is tight, and too tight is broke (stripped).

Nov 18, 2008 | 2006 Chevrolet Silverado 3500

Not finding what you are looking for?
2000 GMC Sonoma Extended Cab Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...