Question about Dodge Ram

Open Question

1999 Dodge Ram 2500 Thermostat torque specs

What are the torque specs for the thermostat housing

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: 1999 Buick Century thermostat question.

patience , and a 13 MM wrench , you gotta get your arms in there deep , that lower bolt does not need to come all the way off , the thermostat housing has a slot at the bottom for easier access , loosen it about 3.4 of the way and you can get the housing out , experience says a premium thermostat will give you grief trying to reinstall , get a regular duty thermostat .reverse procedure.

Posted on Jan 02, 2009

  • 14 Answers

SOURCE: thermostat in 2001 dodge ram 1500

the thermostat is located where the upper radator hose comes off the engine there are two bolts or nuts remove hose and remove housing you will see the thermostat when you do clean old gasket material off block and reverse removal procedure

Posted on Apr 07, 2009

LEFTY64
  • 69 Answers

SOURCE: Need to the torque specs for a 1999 Dodge Durango

Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: Trouble code P1740 on 1999 Dodge Ram 2500

I had the same code on my 2001 dodge 2500. The truck wouldn't shift from 3-4. I pulled the trans pan off and replaced a broken spring ($2.00). It is behind a thin plate with 3-4 small torq screws. You don't have to remove the valvebody. Only took me 45 minutes to fix.

I would like to give thanks to Jeff Russel from Teal automotive. He said this is a very common problem. He sells any part for any automatic Transmision and his prices are very affordable.
Here is a link to the website.
http://www.tealautomotiveinc.com/

Hope this helps.

Posted on Jul 19, 2009

  • 159 Answers

SOURCE: The temperature gauge on my 1999 Dodge Ram 1500 is

Check the gauge by holding in the trip odometer reset button and turn key to run,hold button for 10 seconds this will iniate a diagnostics on all the gauges,and lights if gauge doesn't move during this test replace gauge,if it does move then check the wires on the plug at the engine coolant temp sensor (ects) you can check the sensor by using a ohms meter by unpplugging it and check ohm's or resistance when cold and then start engine as the engine warms up the ohm's reading should gradually lower as the sensor is a thermister and as it warms up the resistance will drop.

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the coolant sensor on a 2004 dodge ram 2500 4 wheel drive


It is located in the thermostat housing or in the intake manifold close to the thermostat housing. Use Teflon paste on the threads Of the new unit and don't over tighten .The sensor will have a wire plugged into it

Jun 14, 2017 | Dodge Cars & Trucks

1 Answer

How to change thermostat in 1995 dodge ram 2500


drain the rad into a pail.
remove the upper rad hose from the thermostat housing.
remove the thermostat housing
remove the gasket/seal (from housing or engine)
remove thermostat

install ne stat & gasket/seal
reinstall housing and hose.

close off rad bottom valve
refill rad with new coolant (with cap off run engine until warm
top up fluid to neck) replace cap.

dispose of old fluid at environmental recycle center

Feb 11, 2015 | 1995 Dodge Ram 2500

1 Answer

I have 2002 ram 2500 gas. starts easy runs well then just dies. will restart in 2 to 5 min. new fuel pump, new gas filter, new plugs and wires, new thermostat (195), new air filter.


Check again piece by piece all that you just replaced to make sure one of then is not faulty from that house.
Check the oxygen sensors
The engine PCM
Catalytic convertor

Wish you luck

Dec 20, 2013 | 1999 Dodge Ram

1 Answer

2008 dodge ram 2500 diesel 4x4 upper and lower ball joint torque specs


Big A-- there are specs for the ball joint stud nuts!!
You're the exact reason I don't take mine to dealerships!!!
Do my own work.
Torque specs are put out for a reason u DA!

Jan 28, 2012 | 2008 Dodge Ram 2500

1 Answer

Where is the thermostat located on a 2004 Dodge Ram 150 6 cylinder.


Follow the hose from the bottom of the radiator. this is the housing and has to bolts. Torque spec I believe is 10 ft-lbs.

Mar 02, 2011 | 2004 Dodge Ram

1 Answer

Where is the thermostat on my 2002 dodge 1500 van and how do you change it?


hi this can be found by locating the top hose on the radiator, follow it back to the engine/motor, there you will find a housing inside the housing you should find the thermostat..you need to drain the cooling system Remove the radiator hose clamp and radiator hose at the thermostat housing, Remove the thermostat housing mounting bolts, remove thermostat housing ,then you can remove the thermostat it self thermostat...hope this helps happy 4th to you

Jul 03, 2010 | 1999 Dodge Ram

1 Answer

2006 dodge ram 2500 heater not blowing hot air....


it sounds more like the thermostat, a thermostat will cost around 8 to 12 dollars,just remove the thermostat housing and replace the old thermostat then reinstall the housing

May 21, 2009 | 2006 Dodge Ram 2500

1 Answer

Putting in new head gaskets, need all of the specs, timing ,


I googled the specs and i found mine it will give numbers and pictures. Sorry i couldn't actuall y give u the answer.

Mar 25, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

99 Dodge Ram 2500 won't heat up


Is the engine fan staying engaged? If so this will not allow you to build addequate engine temp. especially while driving.

Jan 09, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

1999 dodge 2500 4x4 no heat in cab


you may have a couple different problems. the thermostat may be stuck open hterefore not allowing your engine to heat up properly. the coolant will just circulate through the engine and rad without heating up to proper temp. the other problem you may have is that you might have a plugged heater core thus not allowing the coolant to circulate through the core and give you heat.
I would recomend checking the thermostat and see if it is operating properly. an easy way to check it is by opening your rad when the engine is cold. start your truck and watch the coolant in the rad. If the thermostat is stuck open you should see the coolant circulating through the rad. This is not always the best way to check but it is an easy way to see. the other way which involves a little more work is to take the thermostat housing off and physically inspecting the thermostat.
hope this helps you out

Dec 24, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...