Question about Pontiac Firebird

Open Question

How to bleed hydraulic throwout bearing - Firebird Pontiac Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: replaced clutch and throwout bearing now will not go into gear

these can be a pain to bleed is it is the slave is new. Keep bleeding it, try a vacuum leeder or try reverse bleeding with a hand oil pump.

Posted on Jun 28, 2009

Ad
  • 108 Answers

SOURCE: I need to replace the hydraulic throwout bearing,

The clutch throw out bearing is what you are talking about? If it is you should be able to buy them at an auto parts store if not check with your local Ford dealer parts department. But they should be availeable. Good luck.

Posted on Nov 03, 2009

alicantecoli
  • 22156 Answers

SOURCE: I have a 1990 jeep wrangler, the throwout bearing

try using a bearing that is in a metal casiing and not a plastic piece of junk that comes in the clutch kit nowdays ,they always end up going wrong where bearing melts the holder ,unless you can fit a thin telecamit tube and a grease nipple so clutch bearing can be greased every few months like on a good old fashioned commercial vehicle

Posted on Jan 17, 2011

  • 6468 Answers

SOURCE: hydraulic throwout bearing

it is dirty brake fluid that squirts out bleed it until clean fluid come threw

Posted on Sep 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to adjust throw out bearing


There is no adjustments on a clutch throw out bearing.

Nov 07, 2016 | Cars & Trucks

1 Answer

Does hydraulic slave cylinder bearing need greasing?


Hi Sheila:
The clutch slave cylinder pushes against a throwout arm
The throwout arm is a lever and it pushes against the throwout bearing which thenpresses against the clutch plate and dis-engages the clutch.
Throwout bearings are typically sealed units that last until they fail, at which time they get replaced.
You should not have to worry about greasing it.
Hope this helps.
Cheers.

Jan 27, 2016 | 1996 Ford F150 Regular Cab

1 Answer

No clutch disengagement


I hate to say it, but it could be an exploded throwout bearing or defective pressure plate/disc. Fixed one the other day, all new hydraulics, good travel at the fork, pulled trans to find throwout bearing in pieces. Hope this helps.

Oct 02, 2012 | Cars & Trucks

1 Answer

Hydraulic throwout bearing


it is dirty brake fluid that squirts out bleed it until clean fluid come threw

Sep 02, 2012 | 1990 Jeep Wrangler

1 Answer

How to change slave cylinder on f 250 2008


easy job, its located on the bell housing (it actuates the clutch lever to throwout bearing inside transmission). 1. Remove hydraulic line 2.remove mounting bolts. 3.slide slave cylinder out of bellhousing 4. installation is reverse or removal. 5. bleed air out of slave cylinder

Mar 14, 2012 | Cars & Trucks

3 Answers

I replaced clutch master and slave. I even had the flywheel shaved.. now i cant get it into gear when started.


when you had the flywheels shaved it may have moved the pressure plate fingers to far from the throwout bearing

Sep 30, 2010 | 1991 Ford F150

1 Answer

Cant put my 98 Hombre in gear.


There are 4 parts to this system. First is the clutch master cylinder, second is the slave cylinder, third is the clutch throwout bearing, and last is the clutch pressure plate. These are all the parts that can be the issue. The master cylinder is the part that pumps the fluid to the slave cylinder, which pushes on the linkage to the throwout bearing, which pushes on the fingers on the clutch pressure plate, releasing the clutch. If you drained the fluid out, first you need to make sure that all the AIR is out of the system. It's just like brakes, it will not pump if it has air in it. The hydraulic portion of the system rarely gives problems, so here's a question. How old is the clutch in your truck? If it's over 100,000 mi, then you should start suspecting the throwout bearing. Did the truck make any groaning noises when you pressed the clutch recently, and then perhaps it stopped on its own? These are signs of throwout bearings going out. Here's the bit of troubleshooting that you need. go under your truck, and find where the slave cylinder attaches and pushes on the linkage that goes into the bell housing on the transmission. Feel this linkage; it should have very limited to no movement. if it moves significantly, then your throwout bearing went out, and you will need to replace your clutch and throwout bearing. If not, then it's the hydraulic portion of the brakes, and you'll have to troubleshoot between air in the system, master cylinder failure, or slave cylinder failure.

Feb 15, 2010 | 1998 Isuzu Hombre

1 Answer

I was bleeding my clutch now my clutch pedal stuck to the floor on a 1995 f 150


Most modern clutches are hydraulic. It may be that either the clutch master cylinder or slave cylinder are stuck or some sort of restriction in the line. Or, it may be that the throwout bearing or pressure plate have some sort of issue (this requires pulling the tranny and looking at the clutch, pressure plate (plate that rides against the clutch with springs to engage the clutch) and throwout bearing (bearing on the arm that presses against the pressure plate to engage the clutch).

Of course, I am assuming you have checked for any outside restrictions that would not allow the pivot arm to retract (missing spring or piece of ice or debris stuck in there).

Just some ideas :)

Jul 27, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Replaced clutch and throwout bearing now will not go into gear


these can be a pain to bleed is it is the slave is new. Keep bleeding it, try a vacuum leeder or try reverse bleeding with a hand oil pump.

Jun 28, 2009 | 1989 Ford F 150

1 Answer

Clutch wont work


Probably air in the clutch hydraulic system. Did you bleed it? What fluid did you use?

Dec 14, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...