Question about 1997 Nissan Pickup

Open Question

Crank angle sensor 86 Nissan d21 pickup - 1997 Nissan Pickup

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

paconos2007
  • 19 Answers

SOURCE: How can I set ignition timing for a 1993 Nissan pickup D21 2.4L

the mark to the right of the pully will be 0 .. it will be like this. 8 6 4 2 0

Posted on Apr 21, 2009

NismoMaster
  • 146 Answers

SOURCE: Ka24e locate the crank angle sensor

The sensor is located in the bottom inside of the distributor.

Posted on Jul 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to test a crank angle sensor in 86 Nissan hardbody


Sensor detects engine rpm, and piston position. It is integral with the distributor, not replaced separately.
Testing the sensor requires complete testing of the ignition system. Use a spark tester to check for bright,. blue spark. This is called secondary spark test. If weak or no spark, test the ignition coil for proper specs of primary and secondary resistance. If coil is good but no spark, suspect the crank angle sensor. My manual gives no further information on testing the sensor. It contains a light emitting diode and a photo diode. The lights are used to show up the slots in the rotor disc that has 360 slits in it.
Good luck.

Jan 20, 2017 | Nissan Cars & Trucks

1 Answer

Where is the crank sensor on a 86 Nissan d21 pick up 4x4 truck


Inside the distributor. It may also be called a crank angle sensor.

Jul 27, 2015 | Nissan Cars & Trucks

1 Answer

Break and battery light stays on all the time


sold all over earth, what country> we cant guess this....
don't break the brakes....!!!
my guess, you meant the
brake lamps are on keys in pocket. and the battery lamp is dash(charge) glows, keys in pocket. right?
and battery cable kills all this illegal states above. sure.

86 nissan PU.
720 PU>? Datsun>?
or D21 Nissan ( 1986 Dat-SUNS became NISSANS. in USA)
Model years 1986.5 (second half) and later were called Nissan Hardbody Trucks, chassis code D21.

D21 are called HARD BODY trucks. mid year changes.
so???? which is yours.

as you might not ,know , the models are wired diffrent by different exact models and country.
long ago , i had the 86 with the VG30 V6...

so i will roll the dice and answer for
D21
ok?

things off stay on, 101
bad wiring, hacked in wiring, radios,alarms and other things.
all can cause this..... its old and is common on old cars.
but if wiring is not hacked, (id see that in 10seconds in person)
no hacks.
gas engine car not diesel.
USA 86 body
brakes
Im looking now at the schematic and this car has a hot at all times
brake lamp switch. (foot pedal switch)
SO only a bad switch can cause this.... period
now the dash charge (battery ) light stuck on.


my online source ,has the alternator system missing.
so can not comment.
the lamp gets its power from the key switch
if the key switch fails , all warning lanps glow not just the
charge.(battery)
so its not that
my best guess is wiring errors, that put power the the cluster
key off. id bet that is it .

wiring errors to the ignition output is side, key switched power is failing.




Jul 14, 2014 | 1986 Nissan Pickup 4WD 1986

1 Answer

Why isn't my 1987 Nissan D21 pick up not getting fire


check the fusible links near the battery. There are 2 coils. It could be the coil, or power transistor for intake or exhaust. It could be the crank angle sensor. Check the ground connections really well also

Apr 07, 2014 | Cars & Trucks

1 Answer

How do you change the distributor on a 1997 Nissan pick-up?


  1. Remove the two (2) screws securing the distributor cap and remove the cap.
  2. Remove the bolt securing the distributor.
  3. Disconnect the crank angle sensor connector and remove the distributor.
  4. 42331566
  1. Install the distributor, making sure the rotor is aligned as shown when fully seated.
  2. Install the distributor securing bolt and tighten slightly.
  3. Connect the crank angle sensor terminal.
  4. Install the distributor cap and tighten the screws

Jul 02, 2010 | 1997 Nissan Pickup

3 Answers

How do i check my codes in a 86 nissan z24 pickup


The self-diagnostic system identifies malfunctions of signal systems such as sensors, actuators and wire harnesses based on the input signals received by the ECCS control unit. Various malfunctions are coded and displayed on the control unit by a series of blinking red and green lights. Results of the self-diagnosis are retained in the control unit's memory and are displayed when the mode selector, located on the rear of the control unit, Fig. 122, is switched to the On position. When displaying malfunction codes, the code number can be determined by counting the number of light pulses. The red light represents the first digit of the code, while the green light represents the second digit of the code. For example, a Code 32, would be displayed as three flashes of the red light, followed by two flashes of the green light. Malfunction codes can be translated as follows:
  1. Code 11 -- Crank angle sensor circuit malfunction.
  2. Code 12 -- Air flow meter malfunction.
  3. Code 13 -- Water temperature sensor circuit malfunction.
  4. Code 21 -- Ignition signal malfunction.
  5. Code 23 -- Idle switch circuit malfunction.
  6. Code 24 -- Transmission switch and clutch switch circuit malfunction.
  7. Code 32 -- Starter signal malfunction.
  8. Code 42 -- Throttle sensor circuit malfunction.
  9. Code 43 -- Injector circuit malfunction.
  10. Code 44 -- All monitored systems satisfactory.

May 10, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

Location of crank sensor on 94 Nissan Pickup 4cyc


It is located in the distributer. The part is not sold seporate from the distributer. It is only a dealer item the whole distributer for 450.00$. It is also called the crank angle sensor. Just because the code 0335 comes on on the scan does not mean that the sensor is bad. The best thing to do it take it to a dealer.
Actually the one in the distributor is called a camshaft position sensor. You can by rebuilt distributor for around 250.00. The crank shaft position sensor is located on the Transmission housing on the left side.

Nov 17, 2009 | 1994 Nissan Pickup

1 Answer

NIssan d21 86 model headlights


dont touch bulbs with fingers use rubber gloves

Jan 26, 2009 | 1987 Nissan Pickup

Not finding what you are looking for?
1997 Nissan Pickup Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...