Question about Chrysler Pacifica

Open Question

How to install rear driver side quarter window

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 93 Answers

SOURCE: R/H rear quarter window repalcement

tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.

  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

Posted on Jun 02, 2009

Ad
youredone82
  • 426 Answers

SOURCE: i need a driver side rear quarter window replaced.

You should be able to buy this window from a local glass supplier or your dealer. installation is pretty complicated though. i believe those are glued in and require a special tool to remove.

Posted on Aug 27, 2009

SOURCE: need driver side front quarter panel for 1995

While all those parts are available, if there is really that much damage i'd say you may be better off looking for a new car. The doors and front fender bolt on, but the rear quarter panel is spot welded in MANY spots requiring a lot of work to properly replace. You will probably find the best overall deals at the local bone yards. You may be tempted to buy parts online but keep in mind shipping those heavy parts can cost as much as the part. You can use a site such as copartfinder.com to locate a junkyard near by that has the parts you need.

Posted on Nov 26, 2009

Testimonial: "Excellent Feedback"

  • 7353 Answers

SOURCE: Where is the "drivers side rear quarter trim

its the panel nearest the left rear wheel.

Posted on Dec 10, 2010

SOURCE: how to replace subaru quarter glass

Hi Mom, I'm wondering how your spinach pie tastes? Replacing the quarter light is not an easy job, but if you're handy with wrenches and screw drivers here goes. Open the offending door and remove the power window switch by gently lifting it with a thin flat screw driver. Disconnect the cables by releasing the locking tap on the underside of the unit. Remove the back cover of the door release handle by either removing the single screw or un clipping it, Using a Philips screw driver, remove the two deep screws under the arm rest. Borrow the pastry knife from your kitchen and at the lowest part of the door insert it between the panel and the door frame, and then gently pry it towards yourself until you hear the press studs pop open. Repeat the same action all the way around the bottom and up the two side of the door and when loose, lift off the panel and place it out of the way of the kids. Re attach the switch controlling the window and lower the window to where you can reach the bolts (10mm) with a socket wrench. The bolts hold the regulator to the window. Loosen them and remove and lower the regulator all the way down, until you can pull the window up at an angle allowing you to remove it from the door. carefully lift and remove it and put it somewhere safe. remove the rubber weather strips and from the top of the door frame together with the strips inside the rail the window moves on. If you follow the rail of the window to where it is fitted to the door frame you will see another 10mm bolt at the bottom. Before removing that one mark the position as exactly as possible. (The position is critical for smooth operation of the window). Remove the weather strip around the outside of the frame of the door and on top you will see the upper bolt holding the rail (which should also be marked) Remove that and then the rail. The quarter light is held into position by a rubber which surrounds it.Being very careful of any glass which may have remained in the rubber gently remove it and after cleaning it, fit the replacement into the rubber. With the glass in place fitting it into the correct position is not going to be easy. A good idea is to smear a light coating of white petroleum gel onto the parts of the rubber which fit into the door frame before fitting it. When the quarter lite has been fitted and the rail placed in position reassembly is opposite to disassembly. Keep in mind that when fitting back the window it must be aligned with the rails which should be finally tightened after the window is fitted. Now tell me, while you're busy doing that, who's gonna bake the spinach pie? Best regards John

Posted on Sep 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace rear drivers side quarter glass 2004 Chevy impala


This video is not on an Impala, but a quarter window is a quarter window. It should give you an idea of what needs to be done.
How to Replace Quarter Window

Jan 28, 2017 | Chevrolet Impala Cars & Trucks

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

Where is the motor located for my rear quarter panel windows on my 05 Pontiac Montana SV6? And how do I test it?


Rear Quarter Window Actuator - Right (A20)
Behind the right rear interior body panel
Rear Quarter Window Actuator - Left (A20)
Behind the left rear interior body panel
Rear Quarter Window Inoperative

1

Did you review the rear quarter window description and operation?
Go to Step 2
Go to Symptoms - Body Rear End

2

Verify that the rear quarter windows are inoperative.
Do the rear quarter windows operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Are both rear quarter windows inoperative?
Go to Step 4 yes
Go to Step 6 no

4

  1. Turn OFF the ignition.
  2. Disconnect the rear quarter window switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the accessory voltage circuit of the rear quarter window switch harness connector with a test lamp that is connected to a good ground.
Does the test lamp illuminate?
yes Go to Step 5
no Go to Step 7

5

Connect a test lamp between the accessory voltage circuit of the rear quarter window switch harness connector and the ground circuit of the rear quarter window switch harness connector.
Does the test lamp illuminate?
Go to Step 8
Go to Step 10

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

7

Test the accessory voltage circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Retained Accessory Power (RAP) Inoperative in Computer/Integrating Systems

8

Inspect for poor connections at the harness connector of the rear quarter window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 12

9

Inspect for poor connections at the harness connector of the appropriate rear quarter window actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 13

10

Repair the open in the ground circuit of the rear quarter window switch. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

11

Repair the open in the appropriate power window motor rear vents control circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

12

Replace the rear quarter window switch. Refer to Quarter Window Switch Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the appropriate rear quarter window actuator. Refer to Body Side Window Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Sep 28, 2015 | Pontiac Cars & Trucks

1 Answer

Problem with rear drivers side quarter window no going up


Someone will need to remove the left rear trim panel inside the car and see what is the problem.
It could be the electric motor, the window regulator, or the wiring.
God bless your efforts.

Jun 14, 2015 | 2004 Chrysler Sebring Convertible

2 Answers

How do i open and close rear windows


Is the safty switch ingaged. Some switches are on the drivers side window and door lock control panel and sometimes its on the end of the door itself so it's not accessible from inside the car.

Dec 01, 2014 | 2004 Ford Freestar

1 Answer

Where is the "drivers side rear quarter trim


its the panel nearest the left rear wheel.

Dec 10, 2010 | 2003 Lincoln Aviator

1 Answer

I need a driver side rear quarter window replaced. Can I buy just the window or does it only come with installation?


You should be able to buy this window from a local glass supplier or your dealer. installation is pretty complicated though. i believe those are glued in and require a special tool to remove.

Aug 27, 2009 | 2000 Chrysler Sebring

1 Answer

R/H rear quarter window repalcement


tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.
  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

May 29, 2009 | 2004 Ford Focus

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...