Question about 1989 GMC K1500
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hey there.You can purchase a door pin and bushing repair kit to tighten up the hinge area,requires removing the door to replace.If the hinge area is worn to badly,the brass bushings willnot last.Also your window crank handle is held on by a C-clip behind the handle in between the plastic shim and the handle which requires a special tool to remove or a small screwdriver to get the clip off.It is hard to see.The shaft that the handle is on are known to wear also and if thats the case you will need to have the window regulator replaced.Hope this helps.John.
Posted on Mar 10, 2009
iF YOU HAVE NO 'CLICKING' OR ANYTHING THAT INDICATES A DEAD BATTERY - NO DASH LIGHTS ETC, THEN LOOK AT YOUR BATTERY FIRST, TRY TO JUMP IT. THISE ARE TOUGH TO JUMO AND TAKE ALOT OF JUICE TO START YOUR VOLT METER NEEDS TO READ OVER 13 VOLTS, DO NOT CONNECT TO BATTERY FOR BEST RESULTS, CONNET TO ENGINE, NEXT TO THE ALTERNATOR IS A GREAT SPOT, AND THE RED BLOCK THAT IS UNDER THE MASTER BRAKE CYCLINDER (YOU'LL SEE IT WHEN YOUR STANDING AT THE FRONT OF THE TRUCK AND LOOK TO THE RIGHT BETWEEN THE BATTERY AND THE ENGINE)
IF YOU CAN GET ANY JUICE TO THE CAR TO EVEN MAKE THE LIGHTS COME ON AND GET THE INSTUMENTS TO READ OUT, ETC BY USING JUMPER CABLES, THEN MAKE SURE YOU CAN GET JUICE, ALSO MAKE SURE THAT EVERYTHING IS OFF, ROLL DOWN THE DRIVERS WINDOW - OF COURSE YOULL NEED TO MAKE SURE THAT IF THE VEHICLE DOESNT START TO LEAVE THE JUMPER CABLES ON LONG ENOUGHT TO PUT IT BACK UP, AND CLOSE THE DOOR, LEAVING ANY ACCESORIES ON LIKE THE AC, RADIO, ETC JUST MAKES JUMPING THIS 10x HARDER, YOU MIGHT EVEN NEED 2 CARS AND 2 JUMPER CABLE, I THINK THE BEAST NEEDS SOMETHING LIKE 400 AMP TO CRANK OVER, IT'S ON THE BATTERY. ANYWAYS THE REASON WHY YOUR PUTTING THE WINDOW DOWN IS SO YOU DONT LEAVE THE DOOR OPEN AND WASTE JUICE, LEAVE THE KEY IN, BUT JUST PUL IT OUT ENOUGH SO IT'S NOT CHIMING. HAVE THE PERSON WHO IS JUMPING YOU SLOWLY REV THERE ENGINE TO SEND MORE JUCIE TO YOU. I HAVE THE SAME TRUCK AND HAD THIS HAPPENA MILLION TIMES. I FINALLY BOUGHT A JUMPER BOX FOR $50 AND IT SAVED ME ALOT OF HEADACHES. MY PROBLEM WAS I HAD A PROBLEM IN THE ELECTRICAL THAT LEFT A DRAW OPEN - THE IDEA THAT WAS POSTED ABOUT BYPASSING RIGHT TO THE STARTER IS A GREAT ONE, BU IF YOU NOT SURE WHAT YOUR DOING IT'S NOT REALLY THE 1ST AVE I WOULD TAKE, IT WILL JUMP THE TRUCK AND TURN IT OVER (UNLESS THERE IS ANOTHER PROBLEM) BUT WHAT ABOUT THE NEXT TIME? IF YOU PUT THE KEY IN AND GET A READING OF 13 +/- VOLTS ON THE DASH GAUGE THEN YOUR PROBLEM IS MOST LIKELY YOUR SOLINOID (SP) IT'S ABOUT A $60 PART AND EASY TO PUT IN, INVEST THE $$ TO BUY A CHILTONS OF EVEN BETTER A GM SERVICE MANUAL FOR THE TRUCK. WHEN YOU DO GET IT STARTED THE GAUGE SHOULD START TO RISE AND READ 14.5 +/- VOLT CONSISTANTLY, BUT IF YOU GO TO AUTO ZONE THEY WILL 'LOAD TEST' YOUR TRUCK FOR FREE. IF YOU STILL HAVE THE ORIGINAL BATTERY ITS TIME FOR A NEW ONE - AND DONT CHEAP OUT ON THE CHEAPEST ONE, SPEND THE MONEY FOR A GOOD BRAND OF BATTERY, SOMETHING THAT CAN HANDLE THE BEAST, 600 COLD CRANKING AMOS IS WHAT I THINK THE RATING FROM GM IS. IT WILL SAVE YOU A LOT IN THE LONG RUN. AUTO ZONE WILL HOOK UP A TESTER AND LET YOU KNOW IF YOUR BATTERY IS NO GOOD OR YOUR ALT IS BAD, ETC. BUT IT PRETTY MUCH ALLL STARTS WITH THE BATTERY.
THE ONLY OTHER THING IS THAT YOUR VEHICLE MAY BE IN LOCK DOWN IF YOU HAVE A KEY THAT IS WORN REALLY BAD AND ALOT OF MILES YOU MAY NEED TO REPLACE THE IGNITION CYCLINDER - ANOTHER $60.00 FROM THE PARTS COUNTER, AND THEN YOU NEED TO HAVE A BLACKSMITH CODE THE CYCLINDER, $35.00. HOPE I'VE HELPED
Posted on Jan 25, 2010
hi, i have seen this problem ten years ago twice, but i was dumbfounded by the answer. all details aside, I replaced the ecm, and never had the problem again with both of them. this repair was a recommended repair by the local truck depot in my town, they stated the ecm got hot along with the truck and it lost the injector sensor signal. now, don't take this solution and run with it, i haven't repaired a 6.2 diesel in ten years and i maybe off track completely. but at least maybe you could ask around your town or maybe a large truck facility about this. of course, you should take to a shop to have diagnosed. hope i could help.
Posted on Jun 07, 2010
Tips for a great answer:
Jun 22, 2015 | 1989 GMC Sierra
Nov 12, 2014 | 1989 GMC Sierra
Oct 04, 2014 | 1989 GMC Sierra
Apr 08, 2013 | 1997 GMC Sierra
Sep 20, 2012 | 1989 GMC Sierra
Aug 31, 2011 | GMC C1500 Cars & Trucks
May 25, 2010 | 1989 GMC Sierra
Oct 05, 2009 | 1989 GMC Sierra
Apr 29, 2009 | 1989 GMC Sierra
Nov 20, 2008 | 1989 GMC Sierra
33 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: