Question about Cars & Trucks

Open Question

What size fuse would a ford escape cruise control take?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sscullys
  • 984 Answers

SOURCE: 2002 Ford F150. Cruise control stopped working.

Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for the cruise control on a 2013 Ford Escape


You will need to look at that manual for this. The fuse panel should be on the lower left hand side of the steering wheel.

Feb 23, 2015 | 2013 Ford Escape

1 Answer

Where is the fuse for cruise control in 2012 ford escape


There isn't one. The cruise control is a module/computer which is controlled by the ECM. This one has to go on a scanner to see what's wrong. Code readers don't read the cruise.

Jan 14, 2015 | 2012 Ford Escape

1 Answer

Cruse control quit working cannot determine which fuse to check on 2005 escape


Look under the hood at the throttle. There should be another cable that hooks to it. That is for your cruise control. Alot of times it will fall off causing your cruise control not to wwork.

Aug 09, 2011 | 2005 Ford Escape

1 Answer

I have a 2005 Ford escape replaced the booster now the cruise control does not work but the fuse is fine??


check to see if you knocked off the vacuum line to the cruise control servo while doing the booster

May 07, 2011 | 2005 Ford Escape

2 Answers

Cruise control ford escape 2002. ford escape


If the cruise lamp comes on and the cruise does not set i would advise inspecting the cruise cable and make certain it is not broken, if ok the the servo has likely failed.

May 29, 2010 | 2001 Ford Escape

1 Answer

Cruise control stopped working today on my 2005 Ford Escape. What do you think caused this and how can it be fixed?


first id check the fuse if the fuse is good then id try the servo this is the device thats usually round and has a rubber diaphram on the back of it

Oct 03, 2009 | 2005 Ford Escape

2 Answers

I have a 2001 ford escape and the cruise control does not work the indicator light comes on but it will not set


I had the exact same problem on my 2002 Escape. If you remove the engine cover (3 bolts), you will see where the cruise control links to the the throttle body. If your problem is the same as mine, you will see that it is not connected. I believe it is intended to snap on, but it just doesn't stay. I temporarily snapped it in and wrapped electrical tape to prevent it from unsnapping. Worked like a charm.
Hope this helps.

Jul 16, 2009 | 2001 Ford Escape

2 Answers

Cruise control


ok, there are two issues. one could be a fuse that you can exchange out with a working one. secondly, this could be a sensor that is connected to the cruise control assembly under the hood. i would pop the hood to see if the cruse control assembly has became stuck or the cable may have been severed as well.

Mar 02, 2009 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...