Question about 2005 Chrysler PT Cruiser

1 Answer

2001 altima replacing rear wheel stud

I need to replace a wheel stud on the rear tire on my 2001 altima how do i go about doing that

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Chrysler Master
  • 1,449 Answers

Strip it down to your hub the hub holds the studs .it is a push pull fit .but an old nut on it.then hit the top of it .it when then push in.remove the nut. push in the new stud from the rear of the hub.put a larger nut on top of stud ,then your wheel nut to pull the stud into the hub.then remove the wheel nut .then refit the parts taken off.and fit your wheel.

Posted on Dec 30, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Richie_asg1
  • 1036 Answers

SOURCE: my wheel studs broke off

Hi,

You need a stud extractor tool, or if it is flush, a 1/4" drill and a screw extractor.

Posted on Jun 21, 2008

davidsspa572
  • 51 Answers

SOURCE: wheel studs or bolts

Hello Miguel Thank you for using FixYa.com my name is David I hope this Helps you out.
Studs often get damaged from overtightening or from cross threading a nut on the threads. A damaged stud is replaced by unscrewing it from the part and installing a new one of the exact same size.
Stud replacement can be difficult because the stud has often been in place for a long period of time. There has been constant heating and cooling, corrosion, and rust buildup between the stud threads and the internal threads of the part. These factors combine to make some studs very difficult to remove.
The first step in stud removal is to use penetrating fluid to remove the corrosion to free the stud from its mating threads. Soak the area of the threads with penetrating fluid. Allowing the fluid to soak into the threads overnight will make it easier to remove the stud.
Before removing the old stud, measure the distance it sticks up from the surface. This measurement will be needed later when installing the new stud. Use a 6-inch scale to measure from the part surface to the top of the stud. Write the measurement down so it can be referred to later.
A stud remove is used to remove studs. It is installed over the stud. The jaws on the stud remover grip the outside of the stud. A wrench fits on the stud remover and allows the technician to rotate the stud in a counterclockwise direction to remove the stud.
If a stud remover is not available, a stud can be removed with two nuts. Locate two nuts that are the correct thread size. To thread onto the stud. Start one nut and thread it all the way down to the bottom of the stud. This nut will be the drive nut. Start another nut and thread it down until it contacts the first nut. This is called the jam nut.
Put a wrench on the bottom drive nut and hold it in place. Put another wrench on the jam nut and tighten, or "jam" it against the drive nut. The jam nut will now hold the drive nut in position on the stud.
Now put an open-end wrench on the bottom drive nut. Turn the nut in a counterclockwise direction. Turning the nut in this direction causes it to want to unscrew the stud. Instead the forces cause the stud to unscrew.
When the old stud is out, inspect the internal thread. If it appears rusty or damaged, clean up the thread by running the correct size tap through the threads as previously explained. Compare the new stud with the old one. The studs should be exactly the same thread size and the same length.
Check the vehicle's service manual to determine if the threads of the new stud should be coated. If the stud should be locked in place and not easily removed, you may need to use a threadlocking compound or threadsealing compound. Threadlocking compounds are on studs and other fasteners when vibration might cause them to unscrew. Thread sealants are used when a stud extends where liquids, such as oil or coolant, could get on the fastener.
Antiseize compound is used on the stud threads to prevent the stud from reacting with the metal on the internal threads. If this happens, the stud could stick or seize. Antiseize compound prevents this reaction and makes the stud easier to remove the next time.
After the new stud is properly coated, it can be installed. Start the stud by hand, making sure it enters the threads securely. Turn the stud in as far as possible by hand before using any tools. Then use two nuts as described earlier to drive the stud into the part. Use the depth measurement made on the old stud to be sure it is driven in the correct depth.

upper_left.gif grey_line.gif upper_right.gif grey_line.gif Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z grey_line.gif lower_left.gif grey_line.gif lower_right.gif Related Parts: grey_line.gif 0900823d80050bfd.gif Wheel Nut

Posted on Nov 06, 2008

  • 5546 Answers

SOURCE: how to replace lug studs on 2002 chrysler town

I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Posted on Jul 08, 2009

  • 7353 Answers

SOURCE: 2001 Chrysler town and Country tire size

the sticker on the drivers door or door jamb will have that info. plus it is on the side of the tire, starting with P___-__-__

Posted on Sep 23, 2009

  • 834 Answers

SOURCE: I am wanting to replace the rear wheel studs that

You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 dodge caravan with rear draum brakes. Broken wheel stud on right rear wheel. Got the drum off, got the broken stud off. but i cant get the new stud in. not enough space to get the new stud in. Is...


Make sure all tires are chalked,put vehicle in neutral,turn drum till it has a clear spot to knock stud out,use hammer and wooden block,don't use metal punch,can cause burr on end of stud and not want to come out of hole.Both tires on back may need lifted in air to turn.

Jul 05, 2017 | 2006 Dodge Grand Caravan

1 Answer

How to fix rear studs


,First,put block under front tires to keep from moving.If you have rear drum brakes,then you will need to remove hub,Jack up and secure,then remove tire,remove wheel speed sensor,if equipped.remove brake drum,bearing and spindle assembly.To remove stud and replace,you will have to turn bearing and align bad stud so it has room to be removed.get a hammer and a piece of wood to put over stud and knock out,don't use a piece of metal,could mess up end and make hard to get out.After you get new stud in ,get lug nut and tighten to pull stud in.A punch smaller than stud will work.

Aug 16, 2012 | 2001 Ford Focus

2 Answers

Change rear wheel stud


HELLO THERE:
WHEEL STUDS ARE PRESSED INTO THE WHEELS OR DRUMS BY A HYDRAULIC PRESS AND THEY CAN BE REMOVED THE SAME WAY OR THEY CAN BE REMOVED BY USING A SPECIAL SOCKET AND A SLEDGE HAMMER THEY COST ABOUT 3 TO 7 DOLLARS A SET OF 2 AND CAN BE BOUGHT AT ANY PLACE THAT SERVICES WHEELS AND DRUMS OK
hOPE THIS IS VERY HELPFUL FOR YOU
BEST REGARDS MICHAEL

Apr 14, 2010 | 1994 Mitsubishi Diamante

1 Answer

Broken rear wheel stud on a 2005 ford focus zx4 se


  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Sep 25, 2009 | 2005 Ford Focus

1 Answer

What caused all 5 lug studs to break? How do I replace them?


The 24" wheel caused the problem. The car is designed to have 15" wheels on it. The added weight and stress from the monstrous tires is too much for the little studs.

May 30, 2009 | 1981 Lincoln Continental

1 Answer

1986 Audi 5000s tire change instructions


jack car up, put on jack stand,,remove wheel studs/bolts unbolt studs,,remove old wheel replace with new wheel.

Jan 16, 2009 | 1986 Audi 5000 CS

2 Answers

Broken lug stud on rear wheel.


It appears from the excellent picture that the stud has to be spun to line up the half moons at the rear of the stud.Use two thin nuts locked together so you can spin the remaining stud to line up with reliefs in back of the retainer.

Oct 18, 2008 | 2004 Buick LeSabre

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...