Question about Cars & Trucks

Open Question

How to change a o2 front o2 sensor on a mazda rx8

How to change the front o2 sensor on a 2005 mazda rx8

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Pyrhyc
  • 2028 Answers

SOURCE: Mazda mpv O2 sensor wires?

Put some penetrating oil on them and let it soak overnight. This will break up the rust and other build up. Make sure that it is penetrating oil, you can get it at any automotive store.

Posted on Jun 28, 2008

SOURCE: O2 sensor

There should be two O2 sensors. If you look inbetween the engine and radiator following the exhaust manifold down to the exhaust pipe you should run into the 1st O2 sensor, following the pipe down stream under the vehical towards the catalytic converter you should find the second O2 sensor. The 1st O2 should be easy but the 2nd might be difficult depending on your abilities. Coils will depend on 4 or 6 cyls, 1 for each cyl. Repair man, go to, pep boys, napa, auto zone, advanced auto parts to name a few.

Posted on Mar 18, 2009

  • 3 Answers

SOURCE: engine light on 2002 mazda protege is on even after changing o2

Try cleaning the Mass Airflow (MAF) Sensor. My 2002 Protege check engine light came on and it started stalling at stoplights if I didn't keep the engine revved a little. Manager at AutoZone checked the computer code for the light (P0171?), and it said it was running lean. He suggested I try the MAF sensor cleaner they have ($6.99) rather than replacing the 02 sensor, etc.; it made a *significant* difference. (I think I need to do it again to get it totally cleaned out, but the can is for at least 4 cleanings.) The MAF sensor is the large component that air goes through right after the air filter. If you don't have the repair manual for the car (search online for PDF's), you search for the part online to see what it looks like. Mainly, it's a tube about 4" across with some small wire things inside. The cleaner can said it was a 10 minute job; mine took 20 minutes, but only because the tube leading from the MAF sensor to whatever is next (a kind of bent elbow tube, with a couple of accordian-style ripples) tore, and I had to duct-tape that up to seal it. (Still haven't gotten that replaced - found them online for ~$40. Maybe this weekend...)

Posted on May 16, 2009

Mustgo
  • 2359 Answers

SOURCE: i need a wiring diagram for an o2 sensor on a

See page two on this PDF file HERE
http://www.taligentx.com/passat/info/scheduledmaintenance/Bosch-Universal-Oxygen-Sensor-Installation.pdf

Posted on Mar 06, 2010

  • 3640 Answers

SOURCE: 2002 Isuzu Axiom motor backfiring runs rough put new front O2

common causes for back firing, low fuel pressure, or restricted injectors, breakdown of secondary ignition coil, internal ignition coil arching, or a dead spot in throttle position sensor.

Posted on Jul 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install bank 1 o2 sensor on 2001 mazda tribute v6


There are 2 O2 sensors on each bank. Here are some pics of where they are located:


mazda tribute o2 sensor location Google Search

Jan 26, 2016 | 2001 Mazda Tribute

1 Answer

Mazda mpv O2 sensor wires?


Put some penetrating oil on them and let it soak overnight. This will break up the rust and other build up. Make sure that it is penetrating oil, you can get it at any automotive store.

Jun 28, 2008 | 2002 Mazda MPV

1 Answer

I have a 2000 Mazda Protege EX, 1.6 L, manual transmission. Car was driving normal but hesitating and Engine light came in. Checked MAF hose & is not cracked, changed spark plugs & coil, but light...


Many o2 sensors have gone bad but 50% of the time when a code is set on a car about an o2 sensor there is another cause which is changing the emissions & setting the o2 code (ex. vacuum leak, bad plug, injector, it could very well be the cat etc.) The root cause of the problem must be found NOT JUST READING CODES! TAKE YOUR CAR ELSWHERE.

Apr 07, 2017 | Jaguar XJ8 Cars & Trucks

1 Answer

2007 mazda 5 P2195 and p0131 after change o2 sensor one


I have the same problem on my 2006 mazda5. I go a new O2 sensor. Now I get p0131 and p2096 codes

Apr 10, 2012 | 2007 Mazda 5 2.3

1 Answer

Oxygen sensor location in mazda 2001 protege


The front O2 sensor is located at the bottom of the heat shield just before you get to the exhaust. It has a wire connected to it. You will have access to this from the top of the car.You may need a O2 sensor tool that you can borrow from most major auto parts retailer. Disconnect the battery first then unplug the sensor. Using the O2 socket remove the sensor. The sensor should come with a packet of anti seize, apply it to the threads and install it. Plug the sensor back up and connect the battery and you should be done.

Apr 20, 2010 | 2001 Mazda Protege

1 Answer

Where is the bank 2 o2 sensor located on a 2004 Mazda MPV LX


bank 2 is the cylinder in the front of the engine compartment near the radiator, the O2 is either in the exhaust manifold of the bank or in the exhaust pipe off the manifold, round about the size of a jumbo magic marker, you need a special O2 sensor socket to remove it in some cases, if it is in the open then a 7/8 open end wrench will work.

Oct 09, 2009 | 2004 Mazda MPV

1 Answer

Fault code P2096. Which Oxygen sensor is it front or rear? Where can I get one? Mazda quoted £350 plus labour. It's a 2004 RX8 231 registered in the UK.


There are 2 O2 sensors...front is a current based WB...and the rear a more normal narrow band sensor. The rear could probably be retrofitted with a 4wire Bosch sensor...but the Mazda one isn't that out of line in price compared to generic if you figure in the wiring and pissing around

The wideband one in the front is not likely to be available yet aftermarket...so you are likely stuck with an OEM replacement for it....

The PCM will likely throw very specific codes for an O2 sensor failure and there are Monitoring routines that monitor the efficiency of them...so if the code isn't there...it is likely OK. O2 sensors and CAT's are very tightly controlled by emissions regulations...and the OBDII **** does a good job of monitoring that kind of stuff

If you don't know if it's the problem...maybe borrow one from a buddies car if it the front one

Jul 03, 2009 | 2004 Mazda RX-8

1 Answer

O2 sensor


There should be two O2 sensors. If you look inbetween the engine and radiator following the exhaust manifold down to the exhaust pipe you should run into the 1st O2 sensor, following the pipe down stream under the vehical towards the catalytic converter you should find the second O2 sensor. The 1st O2 should be easy but the 2nd might be difficult depending on your abilities. Coils will depend on 4 or 6 cyls, 1 for each cyl. Repair man, go to, pep boys, napa, auto zone, advanced auto parts to name a few.

Mar 18, 2009 | 2001 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...