Question about 2002 Land Rover Freelander

1 Answer

I need bearing sizes for freelander ird

I need to overhual the freelander ird but need bearing sizes first

Posted by on

  • yadayada
    yadayada May 11, 2010

    U will need a service manual for this info.

  • Saidi
    Saidi Jun 06, 2014

    I have overhualed my 1.8K series engine taken the crankshaft from std to .10000 now i need to buy cons and big end bearings. Can anyone help with part numbers for the same?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Hi its Larrysito here is all u need....


1x NKS40), 1x 300849/300811, 1x 32008X, 1x 32006X, 1x 501349/501310, 2x 603049/603011.

1x Crown Wheel and Pinion Set (Ratio:1.80, 21x38)

Posted on Jun 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have overhualed my 1.8K series engine taken the crankshaft from std to .10000 now i need to buy cons and big end bearings. Can anyone help with part numbers for the same? Jun 06, 2014


Normally the crank grinder would supply shells?
Any engine refurb shop would know where to get bearings. Go online to a non franchised LR dealer and see what they know.

Jun 06, 2014 | 2002 Land Rover Freelander

1 Answer

Where is the location of the transmission dipstick on 2005 Land Rover Freelander?


As far as I know, there is none. My 2002 Freelander has a combined fill/level plug about halfway up the IRD unit (the back one) and a similar one on the gearbox. Put the car up on on lift or otherwise get underneath it with a torch to locate it. Fill (awkwardly) from the engine bay until oil pours out and, as long as the car is level, the oil level should be correct.

Oct 01, 2013 | 2005 Land Rover Freelander

1 Answer

I have lost drive to the rear wheels??


ird crown wheel broken. replace ird.

Apr 20, 2010 | 2002 Land Rover Freelander

2 Answers

I have a nocking noise from front of my freelander


hi, im not a mechanic but i had similar problem with my freelander and it was the ird unit (or transfer case ). the shims thorned and there was some damage to the gear

Sep 25, 2009 | 2002 Land Rover Freelander

2 Answers

Car quit moving, but is still running.


is it a front wheel drive or rear wheel drive car ? if it is rear wheel drive it could be the driveline .. if its front wheel it probably is a cv joint they serve the same purpose and are both fairly in expensive to fix as long as they havent damaged other parts such as the yoke on the rear end .. send reply to mrdmburns@cableone.net i will try to help you with this DALE

Aug 29, 2009 | 2002 Land Rover Freelander

1 Answer

Freelander Deisel,constant vibration,shudder.


remove drive shaft and all vcu components, take for a short drive ( car will still drive in 2 wheel mode, if vibration gone suspect could be vcu , if still felt at front suspect ird if still felt in rear check diff mounts then diff out put bearings and nose end play.

Jun 15, 2009 | 2004 Land Rover FreeLander

2 Answers

How to replace viscous assembly


i had a similar problem, my viscous coupling was knocking, when i looked it had broken away from the coupling, but was spinning round and knocking against the floor, i unbolted propshaft from rear, unbolted from the front, you need to use torx head socket. then unbolted middle brackets, (very heavy now, you will need some one else to help) and off it comes, i have been driving it now for 6 months with just front wheel drive.

Apr 30, 2009 | Land Rover Freelander Cars & Trucks

3 Answers

Noisey freelander


Yes, the rear diff is fcuked. It is a common fault on these models. I have a 1.8 2000 model and have now removed the rear prop. This now gives me a perfectly quiet drive, more mpg and frankly not worth getting fixed unless you really need to have 4wd. It is very common for owners to do this. Apparantly after 2001 threy used different diffs (JATCO) which are more heavy duty and don't wear out as fast!

Mar 28, 2009 | 2004 Land Rover FreeLander

1 Answer

Wheel bearings


u will need access to a hydraulic press to remove the bearings and re-install them in the hub, other than that no.

Mar 24, 2009 | 2004 Land Rover FreeLander

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

804 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...