Question about 2005 Lincoln LS

Open Question

My wrench light on and i scanned my problem and the code scanner reads p2106 what the meaning or what the diagnosis of the code

My wrench light stays on.When i put my code scanner on it the scanner code was p2106.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have code p0352,p0102 p0113, p2106 on myford 500,#2coil primary/secondary unit malf.circuit low input intake air temperature sensor circuit hi input throttle actuator control sytm forced lmtd pw


P2106 Ford Throttle Actuator Control System Forced Limited Power

Did you replace the coil #2 ? still have the code ? Have seen this be the coil driver inside the PCM . A transistor supply's a ground for the coil , Coil breaks down inside an sends 40 K volts to the pcm . Video's on youtube ,checking PCM dirvers , #2coil primary/secondary unit malf.circuit low input . How to test computer transistor driver without scan tool


How to test Ford MAF sensor
IAT Intake Air Temperature Sensor Diagnosis P1111 P1112 P0113


Mar 20, 2017 | Cars & Trucks

3 Answers

What is a scan tool


A scan tool allows for the OBD II (On Board Diagnostics) codes to be read from the engine computer in a car. These are common electronic diagnostics tools used by automotive technicians. They are usually used when a check engine light comes on to determine the error codes associated with the check engine light.


They almost always connect via a standard plug on the divers side under the dash.


Most automotive parts supplier will check a car with complementary service to determine the codes stored in a customers automobile.

Nov 21, 2015 | Cars & Trucks

1 Answer

What's your problem? amber engine light stays on after starting my car


Hello
When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

Oct 15, 2012 | 2007 Jaguar X-Type 3.0 Sedan

2 Answers

Engine light stays on


Hello
When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

Sep 06, 2012 | Cars & Trucks

1 Answer

The service engine light stays on 98 winstar


Hello
When the service engine soon light (Also called the check engine light) is turned on this is to alert you to the fact that powertrain control module (computer) has detected a failure somewhere in the systems it controls, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.



Jul 04, 2012 | Chevrolet Tahoe Cars & Trucks

2 Answers

P161


sounds like fuel built up inside your exhaust before the cat then it ignites creating a bang. insuficient spark or timing...

Feb 04, 2012 | 2006 Hyundai Sonata

2 Answers

How do you reset abs sensor on kia sportage


The only way to know where the concern is would be to retrieve the trouble codes.

Without Scan Tool: this information not provided by the manufacturer.

Self-diagnosis procedures (with the diagnostic scan tool)
- With the ignition switch OFF, connect the diagnostic scan tool (Hi-scan pro) to the data link connector located under side of master vacuum in engine compartment.
- Make sure the ignition switch is in the on position, and then choose correct vehicle and model, proceed to diagnostic data link menu item.
- Choose the inspection item after initializing the unit.
- Press malfunction code detection No. 1 and diagnostic scan tool will display any malfunction code found. Notice: A malfunction code is a four-digit number that is continuously output until the failure code is erased by the diagnostic scan tool.
- From the list of failure codes, verify the failed part and repair it according to self-diagnosis procedures.
- After repair, erase all malfunction codes stored in the ABS control unit by selecting inspection item (No. 4).

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 17, 2011 | Cars & Trucks

2 Answers

Starts but won't stay runnig, service engine light stay's on


When the (Service engine) light comes on, you are being notified by the vehicle computer that there is a problem. The computer has stored a code that can be retrieved with a code reader (scan tool). Take your vehicle to the dealer so the technician can read the code and perform a diagnosis on whatever system on the car is malfunctioning. Hope this helps :)

Dec 19, 2010 | 2002 Cadillac Deville

2 Answers

Causes for "Check engine" warning ligth activation


The check engine light comes on and stays on when a problem is detected by the self diagnosis system of your vehicle. Generally, the problem is in the emissions or something that is affecting the effectiveness of the emissions, but other causes can trigger the light to come on, too. To determine the cause, the vehicle will need to be taken to AutoZone or a shop that has an OBD2 scanner, or for 1995 and earlier models, an OBD1 scanner, While a scanner will not give you the magic answer, it will give you a code that narrows down the problem area.

A flashing check engine light is an indication of a severe misfire or problem that is likely to harm your engine. Immediate diagnosis and service is needed.

Some specific causes for the light to be on are:

Gas cap left off, not tightened, not installed correctly, or needs to be replaced

02 sensor

Engine misfire - error might clear itself after 3 complete warm-up cycles; not restarts, but warm-ups

At start up for a bulb check - Should not stay on

Problem in the emission system, including clogged exhaust or the catalytic converter not functioning properly

Dirty/clogged air filter

Dirty MAF sensor

There are pages and pages of items that can cause a check engine light to come on. Having it checked with a scan tool will narrow down the problem area.

Not all systems are able to be read by your local auto parts store. For '95 and earlier cars, OBD I is used and can NOT be read by AutoZone or Advanced Auto. A simple paper clip can be used to jump 2 ports on the diagnostic port and have the Engine light flash a certain sequence. This will then tell you the code to refer to for troubleshooting.

The computer has detected a malfunction and set a code. Have it checked for codes with a scan tool.
There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.

Oct 22, 2010 | 2001 Ford Focus

Not finding what you are looking for?
2005 Lincoln LS Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...