Question about 2007 Saturn Outlook

Open Question

2007 saturn relay. having trouble turning the wheel, and charging system failure light came on

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Charging system failure 07 uplander


Have the vehicle check for DTC'S - diagnostic trouble codes . Most all parts stores will do it free of charge . They will also do charging system testing .

Dec 21, 2016 | 2007 Chevrolet Uplander

1 Answer

My hazzard light on my 2007 Saturn Ion won't turn off. How do I fix this?


sounds like you will need to replace the indicator relay, normally found in the fuse box

Aug 24, 2016 | 2007 Saturn Ion

2 Answers

How to diagnose an ABS problem


You need to find out what code is stored in the ABS control module, if the light is on there is a DTC an the system is disabled ! Don't know if auto part stores can pull ABS codes or not , You'll have to check it out . Personally I say take it to a ASE certified repair shop if you don't know anything about anti lock brakes !
?€¢
Electronic Brake Control Module (EBCM) -- The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


?€¢
System Relays -- The inlet and outlet solenoid relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves, the pump motor relay is energized and supplies battery positive voltage to the pump motor when ABS is activated.


?€¢
Brake Pressure Modulator Valve (BPMV) -- The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


This system can store 10-12 DTC's for something simple as wheel speed sensors to wiring problems to a malfunction of the EBCM . Some of these problems you would need a professional type scan tool ! The antilock brake system on your vehicle is the
BOSCH 8.0 antilock braking system
The vehicle is equipped with the following braking systems:
?€¢
Antilock Brake System (ABS)


?€¢
Dynamic Rear Proportioning (DRP)


?€¢
Traction Control System (TCS) (w/NW7)

The following components are involved in the operation of the above systems:
?€¢
Electronic Brake Control Module (EBCM) -- The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


?€¢
System Relays -- The inlet and outlet solenoid relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves, the pump motor relay is energized and supplies battery positive voltage to the pump motor when ABS is activated.


?€¢
Brake Pressure Modulator Valve (BPMV) -- The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


Important: There is a rubber isolator located under the BPMV and on the mounting studs. The rubber isolators protect the BPMV and the EBCM from vehicle vibrations.


?€¢
The BPMV contains the following components:


-
Pump Motor


-
Inlet Valves (one per wheel)


-
Outlet Valves (one per wheel)


?€¢
Wheel Speed Sensors (WSS) -- As the wheel spins, the wheel speed sensor produces an AC signal. The EBCM uses this alternating current signal to calculate wheel speed. The wheel speed sensors are replaceable only as part of the wheel hub and bearing assemblies.


?€¢
Traction Control Switch (w/NW7) -- The TCS is manually disabled or enabled using the traction control switch.


?€¢
Stop Lamp Switch - The EBCM uses the stop lamp switch as an indication that the brake pedal is applied

Sep 21, 2015 | 2006 Saturn ION

2 Answers

2007 saturn aura


Both these units use the same rotor sensors on the wheels so check for loose wires at the wheels.

Aug 01, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

2007 satur ion 2.2 runs rough after rain


When the light is on have it checked for DTC'S - diagnostic trouble codes , do you know what they are ? Ignition system problem , coil's , plug wires if the vehicle has then . The check engine light code is probably for a engine misfire . Check Engine Light On

Aug 23, 2017 | 2007 Saturn ION-2 Quad Coupe

1 Answer

My 99 expedition won't stay out of all wheel drive I changed the transfer case motor and now it stays I awd for about 10 minute then kicks back out and then the 4x4 light flashes and then it is ok until...


The 4X4 system on your vehicle is computer controlled , GEM module . generic electronic module . The four wheel drive mode switch is a low voltage input to the GEM module . The GEM energizes relay's to control the mode as depicted by input from the mode switch an torque on demand relay an someother inputs . Probably has DTC - diagnostic trouble codes stored in the GEM module .
Transfer Case -Automatic Four-Wheel Drive (A4WD) The automatic 4-wheel drive transfer case system consists of the following:
  • automatic 4WD indicator light
  • brake pedal position (BPP) switch
  • torque on demand (TOD) relay
  • front output shaft speed sensor
  • generic electronic module (GEM)
  • 4WD high indicator light
  • 4WD low indicator light
  • 4WD mode switch
  • rear output shaft speed sensor
  • shift position sensor
  • throttle position output (TPO) from the powertrain control module (PCM)
  • transmission range sensor P1804 Transmission 4-Wheel Drive High Indicator Circuit Failure GEM REFER to Section 413-01 . P1806 Transmission 4-Wheel Drive High Indicator Short Circuit to Battery GEM REFER to Section 413-01 . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure GEM REFER to the Symptom Chart. P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground GEM GO to Pinpoint Test C . P1820 Transmission Transfer Case Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test B . P1822 Transmission Transfer Case Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test B . P1824 Transmission 4-Wheel Drive Clutch Relay Circuit Failure GEM GO to Pinpoint Test A . P1826 Transmission 4-Wheel Drive Low Clutch Relay Circuit to Battery GEM GO to Pinpoint Test A . P1828 Transmission Transfer Case Counter Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test B . P1830 Transmission Transfer Case Counter Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test B . P1836 Transmission Transfer Case Front Shaft Speed Sensor Circuit Failure GEM GO to Pinpoint Test A . P1837 Transmission Transfer Case Rear Shaft Speed Sensor Circuit Failure GEM GO to Pinpoint Test A . P1838 Transmission Transfer Case Shift Motor Circuit Failure GEM REFER to the Symptom Chart. P1846 Transmission Transfer Case Contact Plate 'A' Circuit Failure GEM REFER to the Symptom Chart. P1850 Transmission Transfer Case Contact Plate 'B' Circuit Failure GEM REFER to the Symptom Chart. P1854 Transmission Transfer Case Contact Plate 'C' Circuit Failure GEM REFER to the Symptom Chart. P1858 Transmission Transfer Case Contact Plate 'D' Circuit Failure GEM REFER to the Symptom Chart. P1866 Transmission Transfer Case System Concern - Servicing Required GEM REFER to the Symptom Chart. P1867 Transmission Transfer Case Contact Plate General Circuit Failure GEM REFER to the Symptom Chart. P1874 Transmission Automatic Hall Effect Sensor Power Circuit Failure GEM GO to Pinpoint Test A . P1875 Transmission Automatic Hall Effect Sensor Power Circuit Short to Battery GEM REFER to the Symptom Chart. P1891 Transmission Transfer Case Contact Plate Ground Return Open Circuit GEM REFER to the Symptom Chart. P1892 Trans. Automatic 4-Wheel Drive 4X4 Mechanical Lock Output Circuit Failure GEM GO to Pinpoint Test B . P1893 Trans. Auto. 4-Wheel Drive 4X4 Mechanical Lock Output Short to Battery GEM GO to Pinpoint Test B .
  • Your best bet , take it to a qualified repair shop .

Feb 26, 2018 | Cars & Trucks

1 Answer

A/c compresor wont turn on. where is the relay located


If you need to charge the system, you need a repair
shop to leak check,fix the leak,evacuate the system
& recharge

You can not do that at home with no knowledge or
proper equipment

Be responsible & do not pollute the atmosphere or
ruin your car by letting air in & overcharging

If you ever have one relay failure in 50 years, it would be a lot

You jump the low pressure switch to pull in compressor
clutch

You can not add refrigerant without the proper pressure &
temperature charts,knowing ambient outside temp,and
having the manifold gauge set to do so,leave it to a trained
professional

Sep 15, 2012 | 2003 Saturn VUE

2 Answers

2007 SATURN ION POWER STEERING MESSAGE. MESSAGE FALSHES AND STEERING IS TOUGH TO TURN. i TURN CAR OFF AND TURN IT BACK ON AND IT'S FINE UNTIL MESSAGE COMES ON AGAIN. IT MAKES NO NOISE.


  • You have an electronic power steering system.

  • Your power steering module, steering assist motor and the steering sensor could all be problems. You will have to have a scan performed to see what the exact problem is. There is no other way.

  • The power steering aides you in turning the wheel. When the light comes on there is a malfunction and this is why it is hard to turn the wheel, because the steering assistance of the power steering is gone at that time. Turning the car off just temporarily resets the PCM.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards,Tony

Sep 16, 2011 | 2007 Saturn ION-2 Quad Coupe

2 Answers

2003 saturn vue: engine shut off while driving; tried to restart. Starter and motor turned but would not restart. 1 hour later started and drove it. This is second time in 3 weeks. What could it be?


it could be the ignition or fuel system's failure. but most cases to this kind of trouble it has failure to their igniter( ignition coil).

Feb 10, 2011 | 2003 Saturn VUE

1 Answer

New battery and alternator. Battery still won't hold charge


Check all your fuses if you had a system failure it could have blown a fuse. I am not sure on your vehicle where the fuse is in the car or under the hood it could also have a relay. You can check your alternator by checking the voltage at the back of the alternator where the big wire bolts on. You should have 14+ volts at the alternator.

May 24, 2009 | 2007 Chevrolet Uplander

Not finding what you are looking for?
2007 Saturn Outlook Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...