Question about Peugeot Cars & Trucks

Open Question

Where is the crankshaft position sensor on 2005 peugeot 407 1.6hdi?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

rvrfsh
  • 3 Answers

SOURCE: location of crankshaft position sensor

I have a 2005 neon and i found mu crank sensor on the radiator side of the block driver side of center directly below the starter. I hope this helps..

Posted on Apr 15, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 37 Answers

SOURCE: where is the crankshaft position sensor on a 2005

Passenger side of the engine just above the oil pan. Look for the wire harness going into the block.

Posted on Nov 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

2 Answers

Where is located the crankshaft position sensor for 2005 dodge sprinter 2500


Is this a deisel motor? If so, it will not have a crankshaft sensor

Jul 19, 2015 | Dodge Cars & Trucks

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

1 Answer

Engine management light on trouble code P0335


P0335 - Crankshaft Position Sensor 'A' Circuit Malfunction

Possible causes- Faulty crankshaft position sensor (most common)
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery causing slow engine crank over.

Oct 25, 2012 | 2005 Fiat Punto

1 Answer

P1613 Configuration How to fix that ?


Check for coolant that might have leaked into the crankshaft position sensors wire connector.Clean it with a non-chlronated brake cleaner then reset the computer.

Jan 19, 2012 | 2005 Peugeot 406

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

HELP ! Sensor crankshaft position SUZUKI AERIO SX AWD 2.3L 2005.How to replace under the scheme ?


Welcome to FixYa.com
Crankshaft Position (CKP) Sensor Removal and Installation

Removal

1. Remove engine with transmission from vehicle.

2. Remove transmission from engine and then remove flywheel or drive plate from crankshaft.

3. Disconnect connector from crankshaft position sensor.

4. Remove crankshaft position sensor (1) from cylinder block (2).

Installation

Image

Reverse removal procedure noting the following.

- Check to make sure that crankshaft position sensor (1) is free from any metal particles and

damage.

- Apply engine oil to O-ring of sensor.

- Install crankshaft position sensor to cylinder block (2) with specified torque.

Tightening torque

Crankshaft position sensor bolt a: 6 N.m (0.6 kg-m, 4.5 lb-fl)

- Connect connector and fix wire harness with clamp securely. Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician
leedavidian_133.png

Feb 06, 2011 | 2005 Suzuki Aerio SX

1 Answer

Peugot 106 no spark. AA man send crankshaft sensor


it will probably be crank position sensor
this is located on the front of the engine where the engine meets the gearbox

Nov 11, 2009 | Peugeot 405 Cars & Trucks

1 Answer

P1613 fault code & engine will not rev over 3000 rpm when you get to 3000rpm it then fluctutated between 2500 rpm & 3000 rpm causing the car to buckaroo


Crank sensor or engine speed sensor is faulty.

Fault:
Irregular power loss on accelerating
The speed of the engine is limited till 2500rpm
Frequent loss of crankshaft position sensor signal

Cause:
It is caused due to leaking from thermostat housing into crankshaft position sensor harness multi-plug

Remedy:
Check and clean the crankshaft position sensor harness multi-plug contacts. Rectify the engine coolant leak from the thermostat housing if found. Take a note of the engine coolant level and monitor it for changes, showing a leak is indeed occurring.

Oct 24, 2009 | 2005 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

729 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...