Question about 2008 Cadillac Escalade

Open Question

Need torque specs for 6 bolts that connect half axle on 2008 Escalade?

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14036 Answers

SOURCE: Cylinder head bolt torque specs for 2000 Cadillac

YOU NEED NEW HEAD BOLTS OLD HEAD BOLTS BEEN STRETCHED. YOU HAVE TORQUE HEAD BOLTS IN FIVE PASSES. FIRST PASS TORQUE HEAD BOLTS 18 FT LBS. SECOND PASS ADD ADDITIONAL 90 DEGREES.THIRD PASS ADD ADDITIONAL 90 DEGREES.FOURTH PASS ADD ADDITIONAL 90 DEGREES.FIFTH PASS ADD 15 DEGREES.

Posted on Dec 22, 2010

  • 496 Answers

SOURCE: I need head bolt torque specs for a 2000 cadillac deville dts..

DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Posted on Apr 16, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the 5 bolts that secure the Transmission Manual Valve Position Pressure Switch


Torque specs on on 4L60 tranny pan in 04 escalade??

www.cadillacforums.com/.../cadillac-escalade.../260881-torque-specs-4l6...
May 26, 2012 - 3 posts - ‎3 authors Has 104000 miles on it now, figured it's time to change the filter and the fluid. ...Cadillac Escalade, EXT and ESV Forum - 1999 - 2006 Discussion, ... Flywheel toTorque Converter Bolt ... Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt ... Powered by vBulletin® Version 4.1.5 Re: SRX V8 Valve Cover Gasket Replacement Write Up ...
14 posts
Jun 10, 2015
2000 DTS Setting up Internal Mode Switch - 4T80E ...
9 posts
Aug 27, 2014
More results from www.cadillacforums.com

Nov 19, 2015 | 2000 Cadillac Escalade

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

1 Answer

How many pounds of torque for a 2000 escalade head bolts?


Check your shop manual! However, I think the stock bolts are a one time use only item and if you replace them with better quality ARP bolts, they will come with special lube and torque value. If you replace with dealer bolts, service department should be able to give stock spec's

Dec 29, 2014 | 2000 Cadillac Escalade

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

Front hub torque specs


The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

Dec 29, 2013 | Dodge Cars & Trucks

1 Answer

I need to know the torque-specs on the bolts for the CV shaft on a 1993 90 s. I need both the specs for the 6 bolts that hold the cv shaft to the transmission, as well as the 1 big outer-spindle...


Axle shaft bolt should be torqued to 147 Ft Lbs plus 1/4 turn.

The six CV joint bolts should be 59 Ft Lbs.

Ball joint nut should be 48 Ft Lbs

Hope this helps.

Sep 08, 2011 | 1993 Audi 90

1 Answer

Need torque specs on axle nuts for dana 50 rear axle


Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Feb 19, 2011 | 1986 Ford F 250

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...