Question about Cars & Trucks

Open Question

Adjust valve. Om422 truck engine - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why adjust the tappets when engine is cold?


adjust the tappets when cold allows you to get the engine running with out causing valve or engine damage
you do the final adjustment when hot as the stem expands in length and takes up the cold adjustment
if the cold adjustment is too close because you didn't make that adjustment the the valves will not seat properly when hot and will burn the edges of the valves

Aug 03, 2016 | Cars & Trucks

1 Answer

Send the valve settings for a toyota 3L engine


Valve setting? Most engine valves have an automatic adjuster to self adjust the setting. You didn't say you had it apart. So, I'm thinking you have a dirty condition that would make the adjuster or valve tap. If so good additives just for both those conditions can restore the adjusting by cleaning and freeing the ailing parts. Try the link below for more info and needed product. Stops noisy engine valve tap in 10 minutes or free Add Driving ends tap

Nov 04, 2014 | 2007 Toyota Hilux 2.7

2 Answers

Valve lash procedure


i need to know how to adjust the valves on 02 pont sunfire

Nov 20, 2011 | 1991 Chevrolet K1500

1 Answer

How to do valve adjustment 2002 escort 2.0 liter SOHC


The valves in this engine are a hydraulic design and require no adjustment nor is there any provision for adjustment in the design. If the valves are noisy then you have defective valve train moving parts, commonly on this engine that is the hydraulic followers (referred to as "Lifters" in older OHV engines).

Oct 10, 2011 | 2002 Ford Escort

1 Answer

I need to adjust the valves


12th inlet and 14 exhaust ,4cyl engine all valves add to 9 ,,example--- no1 down adjust no8 ----no2 down adjust no7 all values add to 9 simple if you take your time to count the valve thats down subtract from 9 and then adjust that number ,this system works on all engine regardless of what the haynes book says ,6 cyl engine then its 13 ,and a 8 cyl engine then 17 ,in cases of 16 valves in a 4 cyl engine then its still the same as two valves work as one ,simple

Sep 26, 2011 | 1987 Subaru Gl 4WD

2 Answers

Overhead valves making noise like they need ajusting


Valve Lash ADJUSTMENT 1.6L Engines NOTE: Measure valve clearance with the engine cold.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the valve cover.
  3. Set the engine to Top Dead Center (TDC) of the compression stroke for the cylinder to be adjusted.
  4. Check the valve clearance. The valve clearance specifications are as follows:
    • Intake valves: 0.005-0.007 inches (0.13-0.17mm)
    • Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  5. After adjustment, tighten the locknuts to 11-14 ft. lbs. (15-19 Nm).
  6. Repeat for each valve to be adjusted.
1.8L, 2.0L and 2.5L Engines The 1.8L, 2.0L and 2.5L engines utilize automatic hydraulic lash adjusters to maintain proper valve lash at all times. Periodic valve lash inspection and adjustment is not necessary or possible. prev.gif next.gif

Sep 14, 2010 | 2000 Chevrolet Tracker

1 Answer

I have to adjust valve clearance on my ford 110 engine from 1994. year. Can you tell me right clearance of inlet valves and inlet valves


What engine do you have (size)? Valve adjustment is generally a thing of the past after the introduction of hydraulic lifters (no adjustment). In 1994 your engine should have hydraulic lifters and are not adjustable. Is this a high performance engine? New camshaft, lifter, and rocker set that are adjustable?

Aug 04, 2010 | Ford F-100 Cars & Trucks

1 Answer

How to adjust valve clearance on a 1999 sunfire 2.2L engin. I heard noise in my engine and I am thinking its only the valve clearance need to be adjust.


There is no valve adjustment for that engine, Hydraulic lifters, You might remove the valve cover and see if you have a rocker arm loose

Mar 13, 2010 | 1999 Pontiac Sunfire

1 Answer

Want to know what the valve clearances are for my 1999 hyndai excel


Adjust the jet valve clearance before the adjustment of the
intake valve clearance.
Jet valve clearance (hot engine)
[Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

now adjust valve clearance
Valve clearance (hot engine) [Standard value]
Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

Jul 30, 2009 | 1990 Hyundai Excel

2 Answers

My valves are making a tapping noise do i need to adj. valves


Before adjusting the valves, 1. check the oil level 2. use an engine cleaner that you add to the oil (berryman's or equivalent) and run thru the engine for 30 minutes 3. change oil and filter 4 run and check for tappet noise. This may improve things without opening things up.

Jun 11, 2009 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...