Question about Cars & Trucks

Open Question

My headlights don't work in my 1999 winnebago adventurer rv

Headlights dont work only high beams work

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: no driving or high beam headlights

Hi,

To my knowledge a 2003 Toyota Camry uses a dual filament halogen bulb, either by Osram, Philips or Sylavania. If on the dashboard, the blue indicator lits when the switch is moved to bright or the passlight is engaged but no headlight, then it could jut be busted bulb (or part of it since you still have driving/low beam). In some cases, it could be the relay that supplies power direct to the bulb. At other times, it could be fuse(s) assigned to high beam. At certain instances, it could be also a loose, corroded or burned connector.

Corrective measure for your concern would be to check the 2 bulbs. This is performed by removing the rear covering (rubber or plastic cap) of the headlight assembly from the rear. The bulbs are held in place by a spring clip that needs to be unlatched from the base/holder. Carefully remove the bulb taking care not to touch the glass envelope. The filaments would be readily visible and cut/breaks would be apparent. If determined that one of the filaments (high beam) is open, replace the bulb(s).

If the bulbs prove to be OK, you need to work yourself backwards tracing the wiring harness. After the bulb, check the 3 prong connector for any corrosion or scorching/burnt marks; clean as maybe required. Next to check would be the relay that provides the +12VDC and then the fuse.

I doubt if the dashboard or steering wheel components involve with headlights may be at fault.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 02, 2008

  • 1114 Answers

SOURCE: headlights on reg beam dont work - what to do

when you switch your signal arm push forward for hi beam pull back low beam if you have regular beam and both beams are present then most likely it is your head light hand switch!! if fuse was blown you would have no head lights at all,so i would start with the swich good place to begin!

Posted on Jan 03, 2009

  • 6 Answers

SOURCE: saab 95 headlights dont work high work and drive lights stay on

IF THE BULBS ARE OK CHECK THE HEADLIGHT MODULE(IT LOOKS LIKE A RELAY, ORANGE CASE I THINK) TRY WIGGLING IT,IM PRETTY SURE THATS IT. THEY GO BAD ALOT ON SAABS. IT SHOULD BE IN THE ENGINE CONPARTMENT

Posted on Jan 30, 2009

  • 420 Answers

SOURCE: Headlights not working

Have you tried new bulbs?

Posted on Apr 21, 2009

  • 87 Answers

SOURCE: Drl and high beams dont work

Check the bulbs -- the daytime running lamps use the highbeams on the resistor -- There are two filliments per bulb one high; one low. If both high beam filliments are out nothing will work....replace bulbs if this is the case.

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High beam headlights stuck on replaced switch same problem


It can be issue with headlight switch,but as its already been replaced.Try disconnecting high beam headlight wiring from headlight assembly and reconnect direct external wire from headlight switch to headlight assembly,then by switch see if headlight is getting off and turning on or not.
See below related help links,similar to your issue.Click the link below:----
Only high beams work but head lights not working on Ford F350?

http://howtobyme.blogspot.com/2011/11/only-high-beams-work-but-head-lights.html

----------------
Only high beams working on GMC Savana?---------- High beams stopped working but headlights still work? http://howtobyme.blogspot.com/2011/11/highbeams-stopped-working-but.html
---------- Working of Headlight switch? ----------

Both headlight bulbs blow together?
----------

Car headlight bulbs don't last long?

------------ Only one head light works on 2001 Dodge Caravan? http://howtobyme.blogspot.com/2011/11/only-one-head-light-works-on-2001-dodge.html

----------
these will help.
Thanks.

Nov 06, 2012 | 2007 Chevrolet Tahoe

1 Answer

Low beam headlight drivers side don`t work. high beam it works.


Check tour bulbs first and replace if blown. If OK then check wiring backwards from light to dip switch.

Oct 05, 2012 | 1996 Ford Explorer

1 Answer

My headlights went out dont know what the problem is low beam dont work high beams works


it may be the dimmer switch located on the base of the steering colume that is not working on the low beam side.also the headlights themselves may need changing if the low beam filament is burnt out and you didn`t realize one was burnt out then the other one burnt out.if that`s not the case then it could be a bad connection at the plug connector for the low beam or for some reason power is lost between the switch and the headlight.you don`t say if this has day time running lights,if it does then it could be the drl relay that is bad.

Apr 21, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

No headlights. Low beam out High beam work. I replaced the bulbs and check all fuses. Could it be the headlamp switch


could be becauce if you dont have low beams and high beams do work once you replace them with new bulbs low beams should work.

Sep 24, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Drl and high beams dont work


Check the bulbs -- the daytime running lamps use the highbeams on the resistor -- There are two filliments per bulb one high; one low. If both high beam filliments are out nothing will work....replace bulbs if this is the case.

Aug 02, 2009 | 1999 Pontiac Sunfire

1 Answer

Low beam not work !!


replace the headlight bulbs. Usually when the bulbs blow out the low beam blows out first, but the high beams still work. If you want and need both low and high beams to work then replace the headlight bulbs with brand new ones and I garauntee that both low and high beams will work

Mar 27, 2009 | 1999 Dodge Caravan

1 Answer

Saab 95 headlights dont work high work and drive lights stay on


IF THE BULBS ARE OK CHECK THE HEADLIGHT MODULE(IT LOOKS LIKE A RELAY, ORANGE CASE I THINK) TRY WIGGLING IT,IM PRETTY SURE THATS IT. THEY GO BAD ALOT ON SAABS. IT SHOULD BE IN THE ENGINE CONPARTMENT

Jan 30, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...