Question about 2001 Ford Taurus

Open Question

2001 ford taurus tachometer and mph gauge jumping

Gauge for mph and rpm jumping and bouncing

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Spark plug firing order Ford Taurus 2001

1-4-2-5-3-6

Posted on Apr 08, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: how to bleed the brakes for 2001 ford taurus

Please don't forget to rate:


Bleeding The Brake System Bleeding When any part of the hydraulic system has been disconnected for repair or replacement, air enters the lines causing spongy pedal action (because air can be compressed and brake fluid cannot). To correct this condition, it is necessary to bleed the hydraulic system to ensure all air is purged.
Always begin bleeding the brake system from the furthest wheel cylinder or caliper from the master cylinder; the right rear.
NOTE: The right side of the vehicle is the passenger side. The sides of the vehicle are determined from the driver's perspective. This reference is taken from sitting in the driver's seat, facing forward.
Maintain a full reservoir during the bleeding operation. Never use brake fluid that has been drained from the hydraulic system, or from an open container, no matter how clean it is. Always use brake fluid from a new, sealed container. The front and rear reservoir will drain as the front or rear brakes are bled.

  1. Park the vehicle on a level surface. Place the vehicle in PARK (automatic) or REVERSE (manual) with the engine OFF, and apply the parking brake. Chock the rear wheels to prevent vehicle movement. NOTE: Wheel chocks may be purchased at your local auto parts store, or a block of wood cut into wedges may be used.
  2. Loosen the lugnuts from all four wheels, but do not remove the lugnuts until the vehicle is raised and supported properly.
  3. Use an approved jack and raise the vehicle high enough to place jack stands under all four corners of the vehicle. Place the jack stands under the frame or axles of the vehicle. Ensure that the front of the vehicle is raised higher than the rear.
  4. Remove the wheels from the vehicle.
  5. Clean all dirt from around the master cylinder fill cap. Remove the cap and fill the master cylinder with brake fluid until the level is within 1/4 in. (6mm) of the top edge of the reservoir.
  6. Clean the bleeder screws at all four wheels. The bleeder screws are located on the back of the brake backing plate (drum brakes) and at the top of the brake calipers (disc brakes).
  7. Attach a length of rubber hose over the bleeder screw and place the other end of the hose in a plastic jar.
  8. Have an assistant place and hold pressure on the brake pedal.
  9. Open the bleeder screw 1/2 - 3/4 turn. As the bleeder is opened, the brake pedal will travel to the floor. Have the assistant inform you when the pedal has bottomed out. NOTE: Do not remove pressure from the brake pedal once it is bottomed out. No movement to the pedal should occur until the bleeder is closed and the assistant is made aware of the situation. Failure to do this will draw more air into the system.
  10. Close the bleeder screw and tell your assistant remove their foot from the brake pedal. Continue this process to purge all air from the system.
  11. When bubbles cease to appear at the end of the bleeder hose, tighten the bleeder screw and remove the hose.
  12. After bleeding each wheel, check the master cylinder fluid level and add fluid accordingly.
  13. Repeat the bleeding operation at the remaining three wheels, ending with the one closet to the master cylinder. The pattern is, RR, LR, RF, LF.
  14. Fill the master cylinder reservoir to the proper level and install the reservoir cap.

Posted on Jul 22, 2009

  • 1146 Answers

SOURCE: I need a replacement keys for 2001 ford taurus

A good place to start is a ford dealer. Often they can cut you a key off the VIN number. You will have to go there in person., and some kind of proof of ownership would be needed!

Posted on Apr 02, 2010

csmock132
  • 4669 Answers

SOURCE: 2001 ford taurus 3.0 liter ohv serpentine belt

3.0 OHV Vin U24dba77.gif

Posted on Apr 03, 2010

  • 123 Answers

SOURCE: diagram of serpintine belt 2001 ford taurus

here it is4777b9b.gif

Posted on Jul 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SE w/A/T. Why does it go only 10 to 25 mph?


2002 Ford Taurus SES won't go over 30MPH and it won't pass first ...

www.taurusclub.com > ... > Maintenance and Repair
Dec 30, 2011 - Drives: 2002 Ford Taurus SES 3.0L V6 Automatic. Posts: 2 ... I tried your advice about 10 minutes ago and drove on 1, backed out of my driveway on to the main road. Once it .... Goes to 3000 4000 rpm's and only 40 mph. Shake at 60 mph and up
Jan 1, 2013
Wont rev over 3500 or go over 25mph
Jan 9, 2012
Will Changing The Throttle Position Sensor Fix My Problem ...
Feb 2, 2008
Top Speed 45 Mph?
Apr 19, 2004
More results from www.taurusclub.com

94 taurus will not go faster than 15 mph - CarGurus


Jan 01, 2016 | 2002 Ford Taurus

1 Answer

2001 ford Taurus speedometer and tachometer quit working after shop put head gasket on


possible there is a wire not connected at a harness point . Probably pulled apart to carry out the work and was not reconnected properly.

Jan 24, 2015 | 2001 Ford Taurus

1 Answer

What would cause temperature gauge bouncing ?


Sounds like the sending unit has an intermittent short to ground. Unhook the the wire from the sending unit, and see if the needle stops jumping around. If it quits jumping around, replace the sending unit. If it still jumps around, you have a bare spot somewhere on the wire and it is hitting ground which will cause the needle to jump. Cut out the bad part of the wire and splice in a new section. That should fix it.

Jul 20, 2014 | 1996 Buick Century

1 Answer

Tach almeter 2001 ford taurus


If everything else in the instrument cluster works, I would say its the tachometer. It gets a signal from the ECM.

Jun 26, 2012 | 2001 Ford Taurus

2 Answers

The gas gauge, tachometer gauge and speedometer gauge are jumping back and forth. what is causing this?


LOOK FOR THE LITES ON THE PANEL TO FLASH OR FADE OFF AND ON, IF SO,THE INSTRUMENT PANEL MAY HAVE A POOR GROUND..

Sep 16, 2010 | 2001 Ford Windstar

1 Answer

1999 Ford Taurus, There are a couple things not working which may influence both, first the RPM Gauge is not working and either is the Cruise Control. I just replaced the Vehicle Speed Sensor and that...


1. Have you looked at your owners manual for location of the cruise control fuses? 2. Same for the tachometer? 3. Do you live in a wet area with alot of rain? Next chance you have, get some electric cleanout spray from NAPA spray into all cruise control connections and tach connections. 4. Check the recalls from Ford there have been issues with 99 cruise econtrol systems.

Jul 03, 2010 | 1999 Ford Taurus

1 Answer

On a 2001 ford taurus what is the exclamatin point on the dash? The light comes on and goes off at times.


Hope this helps.
df697aa.gif


Item Part Number Description 1 — Instrument cluster 2 — Odometer reset shaft 3 — Air bag warning indicator 4 — RH turn signal indicator 5 — Charging system warning indicator 6 — Tachometer 7 — Low oil pressure warning indicator 8 — Brake system warning indicator 9 — Cruise control indicator 10 — Check fuel cap indicator 11 — Anti-lock brake system (ABS) warning indicator 12 — Check transmission indicator 13 — Odometer 14 — Transmission range selector indicator 15 — Trip odometer 16 — Theft indicator 17 — Low coolant indicator (if equipped) 18 — Safety belt warning indicator 19 — Low fuel warning indicator 20 — Fuel gauge 21 — Malfunction indicator lamp (MIL) 22 — Door ajar warning indicator 23 — Traction control indicator (if equipped) 24 — Engine coolant temperature gauge 25 — High beam indicator 26 — LH turn signal indicator 27 — Speedometer

Jun 05, 2010 | 2001 Ford Taurus

1 Answer

The speedometer needle "wobbles"


the speedo cable needs to be replaced,they wear out internally and start to jump arounr inside the sheathing

Aug 31, 2009 | 1995 Ford Taurus

1 Answer

Tachometer bounces and idiot lights come on


well that would lead me to believe that your crank position sensor is going bad, and it will not show up on a computer scan for fault codes, I would have it checked along with cam sensor and replaced if necessary, before you get left somewhere desolate and the car wont start even after the sensor cools down

May 26, 2009 | 2002 Ford Taurus

1 Answer

95 Mustang gt backfiring and RPM's bouncing


sounds like you have jumped a tooth on the timing if not timing out

Feb 02, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...