Question about Cars & Trucks

Open Question

Engine timing diagram

How should timing marks line up when putting a new belt on a mitsubishi 3g83 minitruck engine.

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

Ad
  • 24 Answers

SOURCE: i need to find a timing belt diagram for a 1994 mitsubishi galant

Your car will have the 2.4L SOHC engine in it (AKA 4G64). This manual will show you how to replace the timing belt (and more). Timing belt procedures start on page 33.

http://www.scribd.com/doc/4570538/Mitsubishi-4G63-4G64-Engine

(P.S. this manual also includes the 4G63 engine, you can identify your engine by looking at the procedures for the Single OverHead Cam[or SOHC])

Posted on Apr 07, 2009

  • 81 Answers

SOURCE: engine timing mark diagram

timing on all camshaft im familiar with have a dot stamped on the gear and one on the adjacent gear it meshes with, the trick is to get the two dots to line up with each other for proper timing.
the camshaft runs 2:1 to the crankshaft, so if it wont run, that means your 180 degrees off. line everything back up the dots that is, take the belt off and rotate the cam 360 until the dots are in line again and reinstall the belt.
should fix you up.
hope this helps, good luck

Posted on May 20, 2009

  • 7 Answers

SOURCE: i have 95 eagle summit with 1.8 mitsubishi engine

pdftown.com scroll to bottom of page and look for 1993-1996 Mitsubishi Mirage, follow the links 1 2 3 you will find what your looking for

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2.4 timing marks


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Jan 27, 2012 | 2003 Mitsubishi Outlander

2 Answers

How do u adjust the timing i must have moved the pullies when i was putting on the timing belt after i changed the water pump now its not runnin smooth its off how do i put it back in time


There are marks that you have to line up. The folowing pictures are for DEMOSTRATION PURPOSE ONLY- YOUR MARKS MIGHT BE DIFFERENT. Once all the marks are lined up then you can install the belt, set the tension and rotate the engine two full turns to make sure all the marks line up.

chuckster57_31.gif
chuckster57_32.gif

Apr 18, 2011 | Kia Spectra Cars & Trucks

1 Answer

Need a diagram of how to replace timing belt


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and if you have 150,000+ miles consider replacing the water pump at the same time.
You will have to take off the power steering belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp. Facing the back of the car , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley it holds the adjuster pulley in place . With the adjuster pulley loose , you can use the adjuster bolt to move the pulley to adjust the steering pump belt.
Now take off the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover.
Line up the TDC timing mark on the cover to the mark on the pulley, check that the dot on the cam lines up with the timing arrow on the head, take off the lower pulleys,
take off the lower engine cover, observe the timing marks/arrows and highlight with paint (crank marks and cam marks should all line up if not , put the lower cover and pulley back on and rotate the crankshaft one full turn.), loosen the timing belt tensioner pulley ,take off the timing belt, counter balancer belt if there is one. Now you can unbolt the water pump, scrape the gasket, and replace it.
The good news is, if you have tools,a compressor, an air gun (for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Jan 05, 2011 | 2003 Mitsubishi Lancer

1 Answer

Hi im doing the timing on a 1994 mitsibishi lancer runing a 4g91 engin and am unsure wich timing marks to line the crank pully up with?


Dont even think of putting the belt on unless you have the correct timing marks for the engine check out the mitsubishi forums for technical info

May 30, 2010 | Mitsubishi Lancer Cars & Trucks

2 Answers

How to adadjust timing on my ENGINES:- 4G64 EXT W75C


There is no "outside" adjustment.
This involves getting inside - to the Timing Belt and checking the Timing Marks and Belt.
Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1997 Mitsubishi Galant 2.4L. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1997/make/mitsubishi/model/galant/1997_mitsubishi_galant_timing_belt_diagram_marks.htm

You may also Click on the following free direct Link for Diagrams on the access to the Timing Belt, in the removal of the Serpentine/Drive Belts.
http://www.2carpros.com/car_repair_information/year/1997/make/mitsubishi/model/galant/1997_mitsubishi_galant_drive_belt_routing_diagram.htm


Apr 01, 2010 | 1997 Mitsubishi Galant

1 Answer

Mitsubishi timing belt diagram 2.0 1993


call the jeep or dodge dealer close to u most with still have the diagram and giveit to you free of cost

Oct 29, 2009 | 1993 Eagle Talon

1 Answer

I have installed a new timeing belt and the small belt as well on my 1994 2 litre petrol sohc L300 mitsubishi van i aligned the cam sprocket mark with the top mark inside the cover the crank paint mark did...


It's been a while since I've done a Mitzi. Main belt on crankshaft pulley (should be the biggest) another belt for power steer / A/C - tensioner ok? Although that wouldn't make it run like a old dog. Should be straight forward, locate each of the marks all in line with --> & ....t's. Have you done a timing light check? Good luck hope that adds a little more to think about.

Jun 23, 2009 | Mitsubishi Minivan Cars & Trucks

1 Answer

Engine timing mark diagram


timing on all camshaft im familiar with have a dot stamped on the gear and one on the adjacent gear it meshes with, the trick is to get the two dots to line up with each other for proper timing.
the camshaft runs 2:1 to the crankshaft, so if it wont run, that means your 180 degrees off. line everything back up the dots that is, take the belt off and rotate the cam 360 until the dots are in line again and reinstall the belt.
should fix you up.
hope this helps, good luck

May 20, 2009 | 1993 Mitsubishi 3000GT

1 Answer

Timing belt on a Mitsubishi Nimbus 1994


Make sure you mark cam and crankshaft pulleys with at least two marks on each one.
Also put marks on engine to keep them all lined up.
I use either tippex correction fluid or white paint.

Jan 19, 2009 | Mitsubishi Passenger Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

844 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...