Question about Cars & Trucks

Open Question

Replace ignition cylinder toyota prado 1998 - Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

Ad
landsend
  • 1066 Answers

SOURCE: replace the ignition switch for 1998 toyota corola

first, remove the steering wheel and then remove the top and bottom covers on the steering column

Posted on Mar 26, 2009

  • 14 Answers

SOURCE: How do you rplace an ignition lock cylinder on a 98 toyota corolla

You can do this one yourself if you want it does not require removing the steering wheel. just the plastic housing from the steering column.
remove housing/cover. then look at housing with cylinder lock assem. on bottom about 1.2 inches or so from the end of the lock assembly you will see a very small hole insert metal pin into hole and push in while turning the key in the ignition backwards to accessory positionyou will feel the pin your pushing move in a bit, then you should be able to pull the cylinder assembly out. insert new assembly with key in the same position and turn forward this will install your new assemlby then reassemble your plastic column covers.

Posted on May 26, 2009

  • 324 Answers

SOURCE: I want to replace ignition lock cylinder on my

You have to remove the plastic cover underneath of the steering wheel, after that the metal shield behind the plastic cover. When you remove the shield you will get access to the ignition lock cylinder. Disconnect the wire harness, remove the cylinder, install a new cylinder. Connect the wire harness, install the shield, install the plastic cover.

PS: Before start write down the code for your stereo (if you have one), disconnect the negative cable from the battery. Be careful when you work around the air bags.

Posted on Sep 17, 2009

Testimonial: "Thanks for your help! Great!!!"

Suzman
  • 642 Answers

SOURCE: need to torque cylinder head on a toyota land

Refer to the diagram and torque bolts in sequence as shown in 3 passes. Bolt thread should be lightly oiled. Bolt holes clean of dirt.

suzman_49.jpg
1st pass : 39 N.m. (29ft lb)
Make a mark on the bolt with white-out/chalk or similar in the forward facing edge of the bolt.(see diagram)

suzman_56.jpg
2nd pass : turn bolt through 90 degrees
3rd pass : turn bolt through a further 90 degrees.
Using a mark on the bolt makes it easier to keep track of where in the sequence you are.

Posted on Dec 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head gasket prado


Here's a link to your head gasket,join the site,it's free,then you can use their repair guides like me.
Repair Guides Engine Mechanical Cylinder Head AutoZone com

Apr 07, 2014 | 1998 Toyota Land Cruiser

2 Answers

Toyota Prado Diesel. Electric windows do not operate


Hello! Turn the ignition switch on...Hold the master power window auto up switch for five seconds...Send a comment with results...


Guru........Saailer

Apr 11, 2010 | 2004 Toyota Land Cruiser

1 Answer

My prado ignition is spoil i need an second hand ignition for my prado.


If I can know your location maybe I'll direct you further. But you can visit any Toyota outlet/ Garage. http://www.toyota.com

Mar 18, 2009 | 1997 Toyota Land Cruiser

1 Answer

I can not get my new ignition cyclinder lock in


I just change my prado ignition distributor and my vihicle hardly start well, it used second or more time to start up what the problem?

Feb 14, 2009 | 1997 Toyota Land Cruiser

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...