Question about 2009 Nissan Altima 2.5

Open Question

2009 altima tail light remove housing screw plastic cap

Plastic cap over screw that attaches housing to vehicle

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hiseyj
  • 99 Answers

SOURCE: condensation in light housing

Lance,

You won't be able to get the condensation out of the lamps. The light assemblies are sealed and only have a small hole where ther bulbs go in as well as a small vent. The condensation is normal and will come and go. Even if you put a new light assmebly on the car you could still get the condensation. Go to the dealer for the brake pedal pad.

Posted on Nov 29, 2008

  • 2 Answers

SOURCE: how to remove the tail lights from a 2003 murano

Here's the step by step procedure from the beginning.

  1. Carefully remove the black one inch wide plastic molding strip that runs along the interior side of the tail light. This can be pried off carefully without breaking the plastic clips that hold it in place.
  2. Using a 10mm socket, remove the two bolts that you see which secure the tail light housing.
  3. The tail light housing is also held in place with three or four plastic clips which can be broken rather easily if you don't do this next step carefully. Begin prying the plastic tail light using a plastic putty knife or screwdriver. The top clip comes out pretty easily and so does the bottom one.
  4. On a cold winter day, the middle clip is the one that can break rather easily so gently rock the tail light or wait for warm weather when the plastic isn't brittle.
  5. Once the tail light "bucket" is removed it's a simple matter to replace the bulbs.
d87baef.jpg

Posted on Jan 03, 2009

  • 14036 Answers

SOURCE: changing tail lights?

open trunk if lights on trunk you have a opening you can see the light electrical connector .if lights on lower part of trunk.remove large plastic screws. pull back trunk lining .you will see some more long plastic wing nut screws.remove them and the light cover come out then you replace light bulbs.

Posted on May 03, 2009

  • 1 Answer

SOURCE: 2005 Nissan Altima Tail Light replacement - tab removal

can i get a diagram of where to find the speed sensor locate on a 2005 nissan altima

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the brake light bulb


1.Open the tailgate.
2. Locate the plastic plugs attached to the brake light housing (on the right side of the driver side light, on the left of the passenger side).
3. Carefully pry up the plugs with a screwdriver or other flat tool (I believe there are two).
4. The light should be free to pull out (pull toward the rear of the vehicle). You should see two torx screws.
5. Remove the bolts and pull the housing away from the tail light lens.
6. Twist and pull to remove the correct bulb.
7. Insert the new bulb into the holder and replace the housing.
8. Verify that the replacement bulb(s) are working.
9. Reinstall the torx screws and place the assembly back into it proper location on the vehicle.
10. Push the plugs back into the holes and verify that it is secure.
11. Close the tailgate and check for proper fitment.

May 12, 2014 | 2011 Dodge Nitro Heat

1 Answer

2005 grand cherokee dash lights flash


I have not heard of this before and I am unfamiliar with your vehicle. In most vehicles, if your dash lights are not working your tail lights are also not working (they are on the same fuse). This means whenever your dash lights out, your tail lights are also out, which could put you in the position of getting rear ended by another vehicle or getting a ticket if a police officer see's your tail lights are out at night. It sounds like you are dealing with a loose or broken ground wire. I would start by checking all the tail light wire connections and ground wires located in the back of the vehicle. I have seen ground wires held together by a screw attached to a plastic tail light housing. When the tail light housing breaks it causes an intermittent connection (dim lights, out lights, etc.). A careful inspection of the wires, connectors, and ground wires may turn up the cause of the problem. A simple dab of molten solder, a piece of electrical tape, or a longer screw may be all you need to fix the problem.

Oct 19, 2011 | 2005 Jeep Grand Cherokee

1 Answer

How do i replace a 2006 A6 rear light. I crashed into a wall in the ice and it broke the plastic. I have a full replacement unit.


Rear iignts in rear na, removing and instaiiing

Fig. 325: Rear Lights In Rear Lid, Removing And Installing

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Removing

CAUTiON: • Switch off all electrical components.

. . Switch ignition off and remove ignition key.

o Turn light switch into "0" position.

o Open cap - 1 - for warning triangle.

o Rotate quick-release screw - 2 - counter-clockwise 90 C and remove cover - 3 - from luggage compartment lining - direction of arrow -

Fig. 326: Removing Bulb Socket From Housing, Pressing Catch Bracket Downward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Disconnect electrical harness connector

o Remove bulb socket - 1 - from housing, press catch bracket - 2 - downward - arrow - to do so

Fig. 327: Identifying Nuts, Clamping Bracket, Inner Tail Lamp, And Clamp Mounting

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Unscrew nut - 2 - and remove clamping bracket - 1 -

o Remove nut - 4 - and remove inner tail lamp - 3 - toward outside

o Remove clamp mounting - 5 - from body cut-out

Fig. 328: Identifying Clamp Mounting, Nuts, Inner Tail Lamp, And Tabs

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Installing

Installation is the reverse of removal, noting the following:

NOTE: • Make sure seal between body and tail lamp housing seals properly.

. Attach clamp mounting -2 - at inner tail lamp and screw on nut -3 - loosely.

. Attach inner tail lamp -4 - at body cut-out and make sure grip tabs - arrows - of clamp mounting rest against body cut-out

. Slide clamp mounting - 1 - onto threaded pin of inner tail lamp and tighten nuts - 3 - and -5 -.

Jan 19, 2011 | 2006 Audi A6

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

1 Answer

Replace brake bulb on passanger side


remove the tail lamp from inside trunk should be three or four plastic screws caps holding it in whole light will pull out

Oct 03, 2010 | 2005 Nissan Altima

1 Answer

Replace toyota sienna brake light - Model 2000


If you are talking about the High Brake Light at the top of the tailgate:

1.) Take out the two Phillips head screws in the lens.
2.) Carefully pry the lens straight back . The gasket sticks to the paint so be careful not to rip the foam gasket.
3.) The bulb is a 921 replacement. Easily found size.

If you're talking about the brake light in the tail light assembly:

The instructions for accessing the tail light are in the Owners Manual. Basically, you have to remove one or two screw/bolts from the inside of the vehicle, then there are two snap type plastic hole/receptacle in the plastic tail light assembly. Be very careful that you pry on the housing in the proper direction, perpendicular to the entry of the snap in connector, or you will break the plastic bayonet or attachment to the lens assembly.

It sounds harder than it really is once you take a look at it. If you have a manual, it will tell you and show you how to get the rear tail lights off easily without breaking any of the plastic connectors. Hope this helps.

Mar 10, 2010 | 2000 Toyota Sienna

1 Answer

Changing tail lights?


open trunk if lights on trunk you have a opening you can see the light electrical connector .if lights on lower part of trunk.remove large plastic screws. pull back trunk lining .you will see some more long plastic wing nut screws.remove them and the light cover come out then you replace light bulbs.

May 01, 2009 | 2003 Nissan Altima

1 Answer

How to remove tail light lens on a 2005 kia sorento


Open hatch remove the two screws on side of tailight with hand tap toward outside of vehicle the light has plastic pin on back of light goes in slot and slides about 1/2" outside the car to remove and pushes in and slides toward the hatch to lock in and replace screws (wiki.answers.com, 2009)

Jan 20, 2009 | 2004 Kia Sorento

2 Answers

How to replace tail light


First you need to lift the hatch. There are two screws under plastic caps. Remove the caps and you will be able to unscrew these screws. Carefully using a flat screw driver to pry out the tail light assembly. It have to plastic pin that attached to the car body. do not break the pin. After you pry out the tail light assembly, you will be able to replace the light bulb. Replace everything in a reverse order.

Nov 17, 2008 | 1999 Lexus RX 300

2 Answers

How to remove the tail lights from a 2003 murano


Here's the step by step procedure from the beginning.
  1. Carefully remove the black one inch wide plastic molding strip that runs along the interior side of the tail light. This can be pried off carefully without breaking the plastic clips that hold it in place.
  2. Using a 10mm socket, remove the two bolts that you see which secure the tail light housing.
  3. The tail light housing is also held in place with three or four plastic clips which can be broken rather easily if you don't do this next step carefully. Begin prying the plastic tail light using a plastic putty knife or screwdriver. The top clip comes out pretty easily and so does the bottom one.
  4. On a cold winter day, the middle clip is the one that can break rather easily so gently rock the tail light or wait for warm weather when the plastic isn't brittle.
  5. Once the tail light "bucket" is removed it's a simple matter to replace the bulbs.
d87baef.jpg

Oct 03, 2008 | 2003 Nissan Murano

Not finding what you are looking for?
2009 Nissan Altima 2.5 Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...