Question about Cars & Trucks

Open Question

Chain marks timing for bmw 316ti 2008 - Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ftw1952
  • 10319 Answers

SOURCE: TIMING CHAIN MARKS FOR BMW

No timing marks: you need to use the series of special tools to lock the camshafts and crankshaft into place, then set the vanos. and if it is a M62tu eng you will need a volt/ohm meter to set vanos also.

the tools needed are cam blocks, they hold the cam in place at the rear of the cam and attach to the head. the crank tool is a rod that goes into the flywheel, by way of a hole in the bellhousing to hold the crankshaft. Then there's also the timing chain tensioning tool, and the cam sensor alignment tools (2). Total tool cost about $650-800 for the set. I checked the tool set made by Baum Tools Factory wouldn't have made the tools were it possible to do it by eye. Do you have the tool to tension the timing chain while setting the VAROS with your multimeter? Really, this job should not be attempted unless you're prepared to completely follow the directions, if you try, you'll likely trash the motor.

Posted on May 16, 2011

ginko
  • 19396 Answers

SOURCE: I need the timing chain marks on the camshafts for

Hi.

At the moment I cannot reach the service manual for this model.
Please see if 4.1.1 and 4.1.2 in the timing chain tool manual can help.

Posted on Oct 05, 2010

dttech
  • 4803 Answers

SOURCE: cam chain timing marks an settings for bmw 520i r reg

darren,
Thank you for asking me to help you with your problem. However, this is either not within my level of expertise or the question is unclear or there is not enough information and I cannot help you at ths time.

Posted on Dec 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bmw 120d 2005 engine timing marks chain ,camshafts and oil pump


With special tools. U maybe can rent online. Must use.

Jun 19, 2016 | 2004 BMW 120d

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

Bmw 318i n46 timing chain marks


No timing marks. All done with special tools. Pin for crankshaft at gearbox end, camshaft alignment tools, cam locking tool, chain tesion tool. If you havent done it before, leave it to a professional.

Feb 16, 2015 | BMW Cars & Trucks

1 Answer

Bmw marks timing 7.8l


7.8L is the marking on the windshield wiper fluid reservoir and had nothing to do with the engine. With this level of competence, please do not attempt to replace the timing chain. (they're aren't any timing marks, btw)

Jun 26, 2014 | 2001 BMW X5 3.0

1 Answer

I need timing chain marks on a 97 bmw 528i 6 cylinder


On the internet

Google the question for a picture

Jun 10, 2014 | Cars & Trucks

1 Answer

The ABS warning light on my BMW 316ti is flashing.


The flash may be a faulty brake light switch located on the rear of the brake pedal

Aug 20, 2009 | BMW 3 Series Cars & Trucks

1 Answer

1998 bmw 528i severe misfire


If you've never replaced the timing belt or chain,That would be my first thing I'd check is the Timing belt or chai, just aline the timing marks on crankshaft and then look at the position on the distributor to see if it's pointed in the #1 firing position .

May 02, 2009 | 2008 BMW 528i Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...