Question about Cars & Trucks
I have a Vauxhall Corsa 1.2 16V 2001 hatchback. About 2 days ago the warning symbol car with spanner through it on the dashboard came on and has remained solidly on. I did a home diagnostics test with an Autel MS300 scanner and error code P0170 fuel trim malfunction (be no 1). The car is running fine no miss firing or loss of power. Any ideas to what this error could be, very srange.Many thanks, Tim Porter.
Posted by Anonymous on
Not unusual to be one of those things. Cancel the code and if it returns, then is the time to investigate as it is not a serious fault.
Posted on Jul 27, 2017
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: holden barina 2003
it means its due for service. If u wanna get rid of it without servicing the vehicle then as you start the car simultaneously push the ODOMETER reset button on the dash and it will wipe it. This will however just delay the point your car needs servicing.
Posted on Jun 28, 2008
Polo Coupe 1043,1992, Will not start, can be bumped started, sometimes!!, theres a strange clicking noise from under the air box, when the ignition is on and sometimes the oil pressure light comes on when the car gets upto temperature, then I lose all power and then the engine cuts out. I've recently changed the dizzy cap, rotor arm and battery, all the leads are new ish along with the spark plugs. The previous owner has changed the head and done all that, leaving much of the engine loom unlagged and bare. Could this cause a problem on some of the electrical systems?
Posted on Oct 22, 2008
This is difficult because the computer can't detect a problem, your car thinks everything is ok. In reality what is happening is the electrical component inside the MAF sensor becomes contaminated by the impurities in the air (heavies) These containments imbed themselves to electrical component that senses the air flow causing the sensor to be slightly off, but not enough to trigger the MIL (malfunction indicator lamp). Replace the MAF sensor with a new sensor and you're problem will go away, plus your car get better mileage and performance. (Mass Air Flow MAF sensor
Posted on Jul 14, 2009
SOURCE: I have a Mercedes s500
What all this codes have in common is that every single one of them can be caused by a vacuum leak, so carefully check for cracked, loose or disconnected vacuum hoses, wiring to the coils, fuel pressure regulator, fuel injectors, specially on cylinder 2.
NOTE:After cylinder cut-out system is turned off, the system monitors (through misfire detection) if all intake and exhaust valves are open again.
NOTE:Misfiring may be caused by many faults in the fuel injection system. Usually a misfiring fault is stored with faults pertaining to other components. An engine mechanical fault could also cause a misfire condition.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.
Posted on Dec 03, 2010
Tips for a great answer:
Jul 19, 2016 | Vauxhall Cars & Trucks
Jun 02, 2016 | Vauxhall Cars & Trucks
Oct 25, 2015 | Vauxhall Cars & Trucks
Feb 13, 2015 | Vauxhall Cars & Trucks
Oct 13, 2013 | 2005 Ford Five Hundred
Feb 12, 2012 | Opel Corsa Cars & Trucks
May 13, 2011 | Volkswagen Euro Cars & Trucks
Jun 04, 2008 | 2003 GMC Sierra
19 people viewed this question
Usually answered in minutes!