Question about 2004 Dodge Dakota

Open Question

Location of air intake sensor on dodge dakota 2006 v6 3.7 liter

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: cant find crank position sensor

Can not find crank sensor on 1995 Dodge Dakota how hard is it to replace

Posted on Nov 30, 2008

Ad
66 chrgr
  • 1011 Answers

SOURCE: Crankshaft position sensor location - 1991 Dodge Dakota 5.2L

it is on the passenger side on the back off the motor.there are two allen head bolts or 13mm.it goes into the transmission and normally has rubber at the opening.you should be able to gets this from the top follow middle of valve cover on pass. side the go strait back toward the fire wall.please rate this answer.

Posted on Jan 30, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

  • 114 Answers

SOURCE: Camshaft sensor location

The cam sensor on the 4.7 is located toward the forward edge of the right cylinder head (passenger side). This has a 3 wire connector, tan/with yellow tracer is sensor signal, black / light blue tracer wire is sensor ground and the orange is the 5V supply.

Posted on Mar 22, 2009

  • 111 Answers

SOURCE: Location of oxygen sensor on 2004 dodge dakota

One of them is located on the driver's side of the motor and connects to the exaust manifold.

Posted on May 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the iat sensor located on a 2011 dodge challenger 3.6 liter engine


The intake air temperature (IAT) sensor is located on the intake tube. Simply lift up on the engine cover to remove the cover. Near the front of the engine on the intake air tube will be a small 2 wire sensor, this is the IAT. Lift the release tab and rotate 1/4 turn to the left to remove it.

Nate

Mar 30, 2015 | Dodge Challenger Cars & Trucks

1 Answer

Were is 1997 dodge dekota map sensor located


It's located on the air intake tubing between the air filter box and throttle body.usually rectangular,mounted to intake w/screws,and has a wiring connector.DON'T touch the wires inside,clean only with electrical contact cleaning spray. Best O'Luck

Feb 21, 2015 | 1997 Dodge Dakota

1 Answer

How do i get to the iat sensor on a 2003 Dodge dakota 4.7L V8


The 2-wire Intake Manifold Air Temperature (IAT) sensor is installed in the intake manifold with the sensor element extending into the air stream. It sits on the left side of the engine above the Idle Air Control motor. Hope this helps.

Sep 25, 2012 | 2003 Dodge Dakota Club Cab

2 Answers

I need to find the intake air temperture sensor in my dodge


depends on the engine...
3.7 liter, #1 below:

jturcotte_112.jpg

4.7 liter:

jturcotte_113.jpg

5.7 liter, #2 below:

jturcotte_114.jpg

Jan 01, 2011 | 2006 Dodge Ram 1500

2 Answers

Location of the throttle position sensor


the censor is located adjacent to the throttle control linkage, and has a 3 wire connection plug

May 30, 2010 | 2004 Dodge Dakota

2 Answers

2000 Dodge Dakota Quad Cab is revving up while in Drive and Park?


Sounds like the mass airflow sensor and or the intake air temp sensor. If you can locate and repair these yourself, it will save tons of money for ya.
Hope this helps,
Matt

Sep 14, 2009 | 2001 Dodge Dakota

4 Answers

1998 dodge dakota v8 magnum


Sounds like you have idle air contol problem,sounds like you need your intake cleaned .Go to your local parts store and see if they have 3 step intake cleaning kit. 3M makes a kit and so does valvoline. It should contain a can of Throttle body cleaner a bottle of intake cleaner and a bottle of fuel injector cleaner that you will have to add to your fuel tank. Or you can go to your local valvoline express lube and they can perform this service for around $50.

Sep 20, 2008 | 2006 Dodge Dakota

1 Answer

Having trouble locating


The IAT is in the air cleaner box or the air intake hose to the engine, it measures intake air temperture (IAT), the fuel line runs along the frame rail on the drivers side, crawl under the truck you will see it, it is a 3/8" metal or black plastic line from the fuel tank

Sep 09, 2008 | 2006 Dodge Dakota

2 Answers

Cant find crank position sensor on 1991 dodge dakota with a 3.9 liter engine 2wd auto.


Can not find crank sensor on 1995 Dodge Dakota how hard is it to replace

Jul 24, 2008 | 1995 Dodge Dakota

Not finding what you are looking for?
2004 Dodge Dakota Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...