Question about 2000 Chevrolet Silverado

Open Question

Diagrahm brake lines off 2000 chevy silverado master cylinder

Need diagrahm of brake lines Master cylinders

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: 1998 chevy s10- brake pedal goes to the floor-

Did you put fresh fluid in the master cylinder? I really think you still have air in the lines. To bleed manually, start with the bleeder the greatest distance from the master cylinder, car running, helper pushing down about half way on brake pedal and releasing 3 times, on 3rd time, holding pedal down to half way depressed point while you open the bleeder valve. Repeat until you are sure all air has been flushed out. Check master cyl reservoir level often, because if it gets low and you **** air into the system, you have to start all over again. Go to wheel next greatest distance from master cyl, repeat above, working your way to wheel closest to master cyl last.

Posted on Apr 12, 2009

  • 225 Answers

SOURCE: brake bleeding

if you didn't bleed the lines after putting the master in. then there is a good chance there is air in the lines now. may go through a quart of brake fluid before all the air is out. remember to start at r-rear/ l-rear/ r-front/ l-front last.will take some time. don't forget to adjust the rear brake while your there to help with the pedal

Posted on Aug 13, 2009

Testimonial: "thank you"

  • 53 Answers

SOURCE: 97 Chevy Silverado Brake Problem

start bleding again from left to rigt all the way around.

Posted on Oct 09, 2009

duane_wong
  • 6826 Answers

SOURCE: my 1997 chevy 1500 z71

well, check the brake lines for leakage after adding brake fluid to the full mark. If the brake pedal goes all the way to the floor, it's likely there is a leak somewhere after the master cylinder. If the pedal gets hard after adding fluid, and pumping it several times with the car off, then the master cylinder is still ok.

If air has gotten into the master cylinder, it may have to be bled out on a bench, or using a scanner if that's the way your vehicle is.

Bleeding the Brake System (ABS) Auto Bleed Procedure NOTE: Perform a manual bleeding procedure. If the brake pedal height and firmness results are not achieved, perform the auto bleed procedure below.
NOTE: Perform this procedure when replacing the brake pressure modulator valve or electro-hydraulic control unit.

  1. Perform the manual brake bleeding procedure. Refer to Bleeding the Brake System (non-ABS).
  2. Check the master cylinder fluid level often to prevent running the system dry.
  3. Press the brake pedal firmly and run the Scan Tool Automated Bleed Procedure (for Gas engines) once, or the Function Test (for Diesel engines) four times. Make sure to release the brake pedal between each test.
  4. Perform the manual bleed procedure again. This should remove the remaining air from the brake system.
  5. Bleed the system as many times as needed to obtain the appropriate feel of the brake pedal.

Posted on Dec 18, 2010

  • 1 Answer

SOURCE: Broken brake line on 1990

1990 Chevy 4.3 l engine runs rough at idle half the time-- sometimes it's OK, other days it's rough and can smell raw gas, as tho it's running rich... any ideas?

Posted on Jan 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake pedal wont build any pressure on my 1985 silverado even after i replaced the master cylinder


if you hear a loudish hissing noise when you hit the brakes you may need a new power booster as well my old 85 chevy did the same was booster not master cylinder hope this helps

Jan 30, 2013 | 1985 Chevrolet Chevy

1 Answer

2005 silverado brakes sticking front only after driving little


I had the same problem and replaced both calipers with no change, I figured it was the master cylinder. When I pulled off the master cylinder I saw the vacume booster had about 2 cups of brake fluid in it which leaked from the front of the master cylinder. I replaced master cylinder and vacume booster and brakes work great now.

Aug 30, 2012 | 2001 Chevrolet Silverado 1500

2 Answers

Do 2000 chevy blazers with break pads have wheel cylinders?


brakes pads go with calipers and disc brakes,brake shoes go with drum brakes which has wheel cylinders.

May 21, 2011 | 2000 Chevrolet Blazer

2 Answers

Got a 2000 chevy silverado 1500 4wd changed pads and replaced a line think got air in lines cant get any brake pressure to pedal. do i need to take it to shop to fix problem?


No you need to bleed the brakes.
http://www.youtube.com/watch?v=c0IdNb3hEqI
If that doesn't help you need a master cylinder.
Its where the brake pedal is hooked to. and all the brake lines are hooked to it. if you pump the pedal up and leave little pressure on the brake pedal and it slowly goes down with just the wieght of your foot? That is a sighn your master cylinder is bad.

Feb 02, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

95 chevy silverado, brake fluid was contaminated and master cylinder went out. Replaced master cylinder and flushed out all of the bad fluid. Now the front breaks are locking up when applying medium to...


Hello: You nare going to have to replace/rebuild front calipers, replace Both rubber hoses that go fron the frame to the calipers. You may have to replace the rubber hoses in the rear and the rear wheel cylinders. Contaminated brake fluid creates a expensive and long repair.

Jan 10, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

How do i bledd the brakes on my 2000 chevy silverado after i changed a leaking brake line and the master cylinder ran dry? or tell me the best web site for that promblem


assuming your bleeder nipples are not frozen, you can find many illustrated explanations of this process over on www.youtube.com. This requires a helper, and the half of the brain missing on women dictates this helper be a man. a woman is simply not going to be able to pump the pedal AND FIRMLY HOLD IT DOWN while you bleed out the air. start on the wheel most distant from the master cylinder.

Sep 22, 2010 | 2000 Chevrolet Silverado

1 Answer

Need part numbers for brake lines


Please visit your local full service auto parts store for not only the special lines you will need but also the special bender and special wrenches you will have to use to effect this repair.

Jan 15, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

I had two brake lines that were rotted on my 2000 siverado, so I changed them. I bleed the lines on all four calipers and still pedal goes to the floor. Master cylinder worked just fine right before lines...


You have got air in the lines.
Easiest way to eliminate them is to apply brake line clamps to all the brake lines and check pedal....should be rock solid as its only the master cylinder at work. Simply unclamp one at a time and you will easily detect the problermatic one.

Jan 07, 2010 | 2000 Chevrolet Silverado

1 Answer

Need to replace a brake booster on a 1998 chevy cavalier


get ready for some work.you need to remove the master cylinder nuts that hold master cylinder to brake booster.once you remove nuts you have 2 choices remove master cylinder to remove booster. to keep from bending brake lines.or you can leave master cylinder in pull it toward you easily careful dont bend lines .disconnect vacuum line at booster .go inside vechicle to floor on driver side loosen four nuts on floor to booster .disconnect power brake push rod from brake pedal .dont force pushrod to the sides when disconnecting it.remove four booster nuts then remove booster.when in stalling the new booster loosely install four nuts then connect the push rod to the brake pedal .install new clip tighten the booster unit .if you decide to remove master cylinder use inline wrenches on master cylinder to remove lines.also plug the master cylinder brake line holes to keep from losing all brake fluid.

Apr 26, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...