Question about Nissan Cars & Trucks

Open Question

Nissan maxima slip code, tcs off, service engine light on

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: TCS/SLIP & Check Engine Light Warning

TCS is Traction Control System,and all TCS's are controlled though the Anti Lock Braking (ABS) system.Here's how it works:Each wheel,or in some cases,only the drive wheels have a speed sensor mounted near the hub or axle,and sends a speed signal to the PCM (Powertrain Control Module).The PCM monitors wheel speed continuously,and if it sees a speed out of the ordinary,say for example the right rear tire is spinning and traveling at a much higher speed than the left rear,the PCM will pulse the brakes through the ABS system on the right rear to slow down the right rear so that the left and right wheel speeds match up,this is how the traction control works.So,if you have a TCS problem,the PCM will see this and set a Dignostic Trouble Code (DTC).You need to pull the DTC's out of the system with a scan tool,diagnose and repair the DTC's.It could likely be something as simple as a malfunctioning wheel speed sensor,but you won't know until the codes are pulled out,as this will point in the general direction.Good luck.

Posted on Aug 09, 2008

  • 10 Answers

SOURCE: I put a washable air

Removed the positve and negative charge of battery for 10 minutes then, plug it back the positive first then negative charge and the last step you do is to start the engine. This steps is to clear tcs off, slip and awd lights.

Posted on Jan 24, 2009

MNfisherman
  • 11896 Answers

SOURCE: i am planning to buy a nissan maxima.but the

This wouldn't make the tranny slip. It is making abs kick on when it shouldn't. there is a faulty in the system, most likely abs system causing this. It should be broughten to dealer honestly and I am a mechanic tell you this. It may be bad pump or circuit. I would pull the abs fuse that is in the fuse center under hood most likely. This will prevent abs from locking up on your or quit working on you. Until you get it repaired

Posted on Aug 27, 2009

  • 31 Answers

SOURCE: TCS SLIP KEEPS COMING ON ON A NISSAN MAXIMA JUST

this could be a damaged sensor issue, return the vehicle where you had it serviced with your complaint.

Posted on Sep 30, 2009

dsacco86
  • 1077 Answers

SOURCE: service engine soon, TCS off, SLIP

The oil change wouldn't cause this problem. Just in-case, check the engine oil level.

There are many emission sensors in the car that will make the engine light come ON. Best way to find out what's going on is to have an auto-parts store hook up a engine code reader and tell you what the code means. Most auto-part store will do this for free.

Posted on Oct 11, 2009

Testimonial: "very helpful. i have the mechanic checked the car , the sensor says it has a malfunction in P0340"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service engine soon


Check for any loose wire harness connection or bad contacts.

Aug 18, 2008 | 2002 Nissan Maxima

1 Answer

Just replaced valve covers on Nissan Maxima 2002 due to misfire. Now it smokes and burns oil every start? What's should I do .


If is is only smoking when you first start it up. Most likely the valve guide seals, oil is leaking into the cylinders and smoking when you start it up.

Mar 20, 2016 | 2002 Nissan Maxima

1 Answer

I have the code p0340 for slip n tcs is telling me is a sensor but it show2


I am not sure what "slip n tcs" means but on the 2005 nissan maxima the code P0340 is for the camshaft position sensor circit on bank 1, which is in the rear of the engine compartment. Code P0345 is for camshaft position on bank 2, which is in the front of the engine compartment. The images show the Cyl banks and a cam sensor.6_29_2012_3_38_07_am.gif6_29_2012_3_40_48_am.gif

Jun 29, 2012 | 2005 Nissan Maxima

1 Answer

The ABS, TCS OFF,and SLIP warning lights are on in my 2000 Nissan Maxima. What's the cause and fix?


cud be dirty or low brake fluid----or bad abs module--or more------have system inspected by a brakepro soon before it cost alot or u crash

May 09, 2012 | 2000 Nissan Maxima

1 Answer

The tcs light came on and now the car do not start and the slip sign came too..


engine swap on nissan maxima 2005 code 1212 came up,check wiring all good,the car starts then stall any suggestions,abs fuse is good

Feb 19, 2011 | 2005 Nissan Maxima

1 Answer

TCS SLIP KEEPS COMING ON ON A NISSAN MAXIMA JUST


this could be a damaged sensor issue, return the vehicle where you had it serviced with your complaint.

Sep 30, 2009 | 1999 Lexus ES 300

2 Answers

P1320 trouble code plus


The P1320 code is essentially a coil primary voltage problem. This is traceable using a labscope or accurate DVOM and perhaps you can isolate one or two coils that still work but are close to failure...but there is a nissan service message recommending replacement of ALL coils with updated/improved models to prevent this type of failure. TCS/SLIP is traction control. Most likely you have a speed sensor issue. Be aware, some vehicles can falsely illuminate TCS because of low tire pressure in a single wheel.

Sep 09, 2009 | 2000 Nissan Maxima

1 Answer

My 2000 Nissan Maxima, from time to time, only runs on 5 cylinders. When it malfuntions, the "TCS Off" and "Slip" lights come on as well as the Service Engine Soon light. My son has replaced the coils....


identify thru computer which cylinder is the culprete then check for injector winding problems, bad grounds , have your local tech check for t.s.b. on this problem? also have you replaced the plugs?

Aug 27, 2009 | 2000 Nissan Maxima

1 Answer

Hello, I bought my Maxima SE 2 weeks ago, the light of "service engine soon" turns on and some times the TCS and SLIP lights are turning on and off and whenever these lights come and go, the...


As for trouble codes, and the dealers recommendation. They are true and accurate, although I would get a second opinion from another auto shop other than the dealer. Do not disclose what you already know other than the problems you are expriencing.

Apr 27, 2009 | 2002 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...