Question about 2007 Hyundai Sonata Limited Sedan

1 Answer

I NEED TO REPLACE THE STUDS FROM THE FRONT HUB OF A 98 HONDA PRELUDE PLEASE TELL ME HOE TO TO REMOVE THE HUB AFTER YOU REMOVE THE HUB NUT.

Posted by on

  • Keith Heavilin
    Keith Heavilin May 11, 2010

    Can you upload a picture of the HUB and I will walk you through that.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 95 Answers

You may need a puller to remove it if there are no bolts parent on the back side of the hub, there might be a a bigger nut on the backside, may have to remove steering components

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove rear hub on1996 prelude


Just use a chisel or big flat blade and go along the groove between the cap and the hub. It will come off.

Mar 20, 2014 | 1996 Honda Prelude

1 Answer

Broken wheel studs on a 1987 jeep wrangler


No need to replace the hub just the studs. The come in from the back and are splined to prevent the stud from turning with the nut. Remove the hub --drive out the broken studs and put the new ones in from the rear and drive them back in. Get the studs from the dealer spares or a good tyre retailer.

Apr 08, 2013 | 1987 Jeep Wrangler

3 Answers

How do i get the rear hub off to replace the wheel studs


On some vehicles you may need to slightly pry the hub off. This can be done with a screw driver or the vehicle may have a lug wrench that came with the vehicle. If you are trying to replace the lug studs, then you will have to take the wheel off. Tap the broken stud out and replace it with the new one.

Nov 27, 2010 | Ford F-250 Cars & Trucks

1 Answer

Removing front rotar


rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

May 08, 2010 | 1991 Subaru Legacy

1 Answer

Ihave a 1996 honda accord sedan how do you get the


I'm guessing that the hub is turn while you are trying to remove the nut.
(I can't tell from your question) To prevent the hub from turning while you remove the axle nut, put a prybar between two of the wheel studs and against the ground, then loosen the nut.
I hope this helps you.

Nov 14, 2009 | 1996 Honda Accord

1 Answer

Remove studs from front driver side hub


i belive you need to loossen the 4 botlst in the back if they are not there then the hub assembly is pressed on and will need a hub assembly puller.

May 19, 2009 | 1997 Honda Prelude

1 Answer

REPLACING FRONT HUB STUDS FOR A 98 HONDA PRELUDE


To remove that hub you will destroy the bearing. Because you have to remove it with a slide hammer. It is not necessary to remove the hub to change the studs. Remove the caliper, caliper bridge and rotor. Using a hammer simply knock out the stud or studs you want to replace. Put new stud in and using a sleeve that has a bigger diameter than the stud (I use a big nut, like the one on the axle) put big nut over stud and screw lug nut on stud and tighten until head of stud is flush with hub. Re-install rotor, caliper bridge and caliper. Hope this helps.

May 19, 2009 | 2007 Hyundai Sonata Limited Sedan

1 Answer

1990 Sentra How it remove and replace lug studs on front wheel


there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Feb 27, 2009 | 1990 Nissan Sentra

1 Answer

I have 2 broken wheel studs, front right wheel on a 2003 Accord?


counter clockwise as normal...studs are pressed into hub..need to remove remains and then press new studs in...good luck

Nov 19, 2008 | 2003 Honda Accord

1 Answer

Broke studs front hub 2000 prelude


Remove the wheel and the brake rotor, so that you can get a hand behind the hub flange where the stud is seated. You'll feel the head of the stud back there.

Use a socket extension or something similar, place it against the broken face of the stud, and hammer it out. It'll fall out behind the hub flange, and you can grab it and remove it (if it doesn't fall to the ground). Insert the new stud (available at a parts store for less than $3) into the flange from behind, and press it as hard as you can to get it seated in the splines. Then stack washers onto the stud on the outside, where you can see it, and tighten a lug nut onto the stud. Use your tire iron to tighten the lug nut on the stud - this will pull the stud into place. You may have to stop once or twice to add more washers onto the stud, but keep doing this until you can't tighten it any further and the length of the exposed section of the stud is even with the others. When all studs are replaced, reinstall your rotor and caliper, put the wheel back on (torque it with a torque wrench), and you're done.

Aug 10, 2008 | Honda Prelude Cars & Trucks

Not finding what you are looking for?
2007 Hyundai Sonata Limited Sedan Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...