Question about 1993 Honda Accord

1 Answer

Installation of balance shafts belt . - 1993 Honda Accord

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 205 Answers

Get a service manual which will explain this better then anyone could in words and the timing belt and water pump should be replaced at the same time since they are all easily assessed when doing the job you are doing

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the timing chain


2.2L & 2.3L Engines
Except S2000 with 2.2L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the cylinder head (valve) and upper timing belt covers.
  3. Turn the engine to align the timing marks and set cylinder No. 1 to Top Dead Center (TDC). The white mark on the crankshaft sprocket should align with the pointer on the timing belt cover. The words UP embossed on the camshaft sprocket should be aligned in the upward position. The marks on the edge of the sprocket should be aligned with the cylinder head or the back cover upper edge. Once in this position, the engine must NOT be turned or disturbed.
  4. Remove all necessary components for access to the lower timing belt cover, then remove the cover.
  5. There are two belts in this system; the one running to the camshaft sprocket is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer shaft belt or timing balancer belt. Lock the timing belt adjuster in position, by installing one of the lower timing belt cover bolts to the adjuster arm.
  6. Loosen the timing belt and balancer shafts tensioner adjuster nut, do not loosen the nut more than one turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
  7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  8. Remove the balancer belt sprocket from the crankshaft.
  9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
  10. Remove the timing belt by sliding it off the sprockets. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  11. If defective, remove the belt tensioners by performing the following:
    1. Remove the springs from the balancer belt and the timing belt tensioners.
    2. Remove the adjusting nut from the belt tensioners.
    3. Remove the bolt from the balancer belt adjuster lever, and then remove the lever and the tensioner pulley.
    4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
  12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time.
  13. To install:
    1. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and tighten the mounting bolts to 106 inch lbs. (12 Nm).
    2. If the tensioners were removed, perform the following procedures:
      1. Install the timing belt tensioner lever and the tensioner pulley.
      2. Install the balancer belt pulley and adjuster lever.
      3. Install the adjusting nut and the bolt to the balancer belt adjuster lever.
      4. Install the springs to the tensioners.
      5. Install the lockbolt to the timing belt tensioner, then move it its full deflection and tighten the lockbolt.
      6. Move the balancer it's full deflection and tighten the adjusting nut to hold its position.
    3. The pointer on the crankshaft sprocket should be aligned with the pointer on the oil pump; the camshaft sprocket must be aligned so that the wordUP is at the top of the sprocket and the marks on the edge of the sprocket are aligned with the surfaces of the head or the back cover upper edge.
    4. Install the timing belt on the sprockets in the following sequence: crankshaft sprocket, tensioner sprocket, water pump sprocket and camshaft sprocket.
    5. Check the timing marks to be sure that they did not move.
    6. Loosen, then retighten the timing belt adjusting nut; this will apply the proper amount of tension to the timing belt.
    7. Install the timing balancer belt drive sprocket and the lower timing belt cover.
    8. Install the crankshaft pulley and bolt, tighten the bolt to 181 ft. lbs. (245 Nm). Rotate the crankshaft sprocket 5-6 turns to position the timing belt on the sprockets.
    9. Set the No. 1 cylinder to TDC and loosen the timing belt adjusting nut one turn. Turn the crankshaft counterclockwise until the cam sprocket has moved 3 teeth; this creates tension on the timing belt.
    10. Tighten the timing belt adjusting nut.
    11. Set the crankshaft sprocket and the camshaft sprocket to TDC. If the sprockets do not align, remove the belt to realign the marks, then install the belt.
    12. Remove the crankshaft pulley and the lower cover.
    13. With the timing marks aligned, lock the timing belt adjuster in place with one of the lower cover mounting bolts.
    14. Loosen the adjusting nut and ensure the timing balancer belt adjuster moves freely.
    15. Align the rear timing balancer sprocket using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt/rod into the hole and align the 2.9 in. (74mm) mark with the face of the hole. This will hold the shaft in place during installation.
    16. Align the groove on the front balancer shaft sprocket with the pointer on the oil pump.
    17. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the bolt from the maintenance hole and reinstall the bolt and washer.
    18. Install the crankshaft pulley, then turn the crankshaft sprocket 1 turn counterclockwise and tighten the timing belt adjusting nut to 33 ft. lbs. (45 Nm).
    19. Remove the crankshaft pulley and the bolt locking the timing belt adjuster in place.
    20. Install the lower and upper timing belt covers, and all applicable components. When installing the crankshaft pulley, coat the threads and seating face of the pulley bolt with engine oil, then install and tighten the bolt to 181 ft. lbs. (250 Nm).
    21. Install the cylinder head cover gasket cover to the groove of the cylinder head cover. Before installing the gasket thoroughly clean the seal and the groove. Seat the recesses for the camshaft first, then work it into the groove around the outside edges. Be sure the gasket is seated securely in the corners of the recesses.
    22. Apply liquid gasket to the four corners of the recesses of the cylinder head cover gasket. Do not install the parts if 5 minutes or more have elapsed since applying liquid gasket. After assembly, wait at least 20 minutes before filling the engine with oil.
    23. Install the cylinder head (valve) cover and all other applicable components.
b0b9eb99-5646-47c3-bfea-3ed501154864.jpg dc472561-14cf-4143-9a20-b37ba89f57de.jpg

Jul 02, 2014 | 2004 Honda Accord

1 Answer

Balance shaft belt broke in turn broke timeing belt checked the valves and cames they are good. How do i get the balave shaft timed witht the rest of it this is a 2.4 in a 1999 spider.


Thats happened to alot of people. I usually pull the balance shaft and install a balance shaft removal kit. Other people i know just leave the shafts in but don't install the bal.shaft belt.

HERE is a link to the 4g64 engine overhaul manual

Mar 02, 2011 | 1999 Mitsubishi Eclipse

1 Answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?


check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif

Oct 29, 2010 | 2000 Honda Accord

1 Answer

My balance shaft belt broke while I was driving. It stripped some of the teeth off the timing belt and Im pretty sure it jumped time. I need a diagram to show the timing marks and how to get it back in...


see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Sep 20, 2010 | Honda Odyssey Cars & Trucks

            1 Answer

            Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


            To Install:
            NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
            honda-03-23-3425.gif

            1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

            2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

            3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
            4. Loosen and ten retighten adjusting nut.
            5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
            6. Install lower cover.
            7. Install crankshaft pulley and bolt.
            8. Rotate crankshaft pulley counterclockwise several times to seat belt.
            9. Loosen adjusting nut 1 turn.
            10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
            11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

            12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

            13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
            14. Remove crankshaft pulley and lower cover.
            15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
            16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
            17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

            18. Remove bolt and washer from maintenance hole.
            19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
            20. Insert bolt into maintenance hole and hole in balancer shaft.
            21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

            22. Align groove on balancer shaft with pointer on oil pump housing.
            23. Install balancer belt and loosen adjusting nut 1 turn to tension.
            24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

            25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
            26. Reinstall crankshaft pulley.
            27. Loosen adjusting nut 1 turn.
            28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
            29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
            30. Remove crankshaft pulley.
            31. Install lower cover.
            32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
            33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

              CAUTION
              Do not use impact wrench to perform following step.
            34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
            35. Install dipstick/tube assembly.
            36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
            37. Install cylinder head cover.
            38. Install alternator bracket and alternator.
            39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

            40. Install upper bracket and tighten fasteners in proper numbered sequence.
            41. Install stop.
            42. Install battery and enter radio anti-theft code.
            prev.gif next.gif

            Jul 03, 2010 | Cars & Trucks

            1 Answer

            How do u change the timing belt on a 1990 4 cylinder honda accord?


            Disconnect the wire harness at the distributor.Remove the spark plug closest to the drivers side front tire. Place the palm of your hand over the valve covers empty spark plug hole and have a helper crank the motor over until air pressure pushes past your the palm of your hand. Next, look at the cam shaft wheel and note the direction that the arrow is pointing, the arrow should be pointing straight up IN RELATION TO THE ENGINE not the earth. If it is not, you will need to manually rotate the engine till the cam wheel is infact pointing straight up. Next, Jack up the front of the car and support it with jack stand and remove the front drivers side tire.Next, support the weight of the engine with a floor jack remove the motor mount closest to the drivers side tire To remove it you will need a deep 17mm socket on a heavy duty breaker bar. Next, loosen and remove the power steering belt and alternator belts. To loosen and remove the belts you will need a 10mm wrench and a 12mm wrench. And also a 14mm or 15mm wrench. Next, use a 19mm socket AND an air powered IMPACT wrench to remove the bolt holding on the crank shaft pulley. Next, remove the crankshaft pulley. Next, use a 10mm wrench and/or 10mm socket and remove the bolts holding the plastic engine side cover. Next, loosen the 14mm or 15mm bolt which secures the 2 belt tension wheels. Next, LOOSEN the 10mm bolt that is on the balance shaft tensioner. The balance shaft is the cogged wheel with a small timing mark dot on the side of the wheel. Next, loosen the 10mm bolt on the timing belt tensioner. It's obvious what wheel is the timing belt tensioner. Next, remove the 12mm bolt on the back side of the block (near the balance shaft) a little bit of oil will drip out, this 12mm bolt will allow a long bolt to be inserted into a recessed channel of the balance shaft. This recessed channel is needed to lock the balance shaft in place. A bolt from the air conditioner works great for locking the balance shaft in place. You're basically just pushing the bolt in a hole to keep the balance shaft from spinning.890a27a.jpg Next, remove both the balance shaft belt and timing belt. Then reverse the procedure to complete the new belt installation. EXTREMELY IMPORTANT!!!!!!!!! PLEASE NOTE, the oil pump wheel furthest to the left (closest to the radiator), has a timing mark on the flat face side of the wheel, that timing mark has to be pointing directly to the 9:o'clock position in relation to the engine. The cam wheel has an arrow on the side of one of the "spokes" ...make sure it is pointing straight up in relation to the engine...straight away from the crank shaft. Put the crank wheel on with the arrow pointing straight up to the center of the cam wheel.

            Jun 28, 2010 | 1990 Honda Accord

            2 Answers

            I just replaced the timing belt on a 2004 sonata


            Did you put alot of pressure on belt when installed ? to tight will cause that vibration

            Feb 08, 2010 | Hyundai Motor 2004 Sonata

            1 Answer

            I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


            Dear Friend
            Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
            Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

            Installation:
            ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
            Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
            Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

            Sep 21, 2009 | Hyundai Elantra Cars & Trucks

            1 Answer

            1995 galant broken balance shaft belt


            You sould replace the belt along with the timing belt. If it gets caught in the timing belt you will have MAJOR EGINE DAMAGE!

            Jul 21, 2009 | 2005 Mitsubishi Galant

            1 Answer

            Need to see diagram to timing belt


            i need timing belt diaghram with more information on balance shaft and belt instaling procedure,as I recenlty fitted the balance shaft belt wrong!

            Jul 24, 2008 | 1993 Honda Prelude

            Not finding what you are looking for?
            1993 Honda Accord Logo

            64 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Honda Experts

            yadayada
            yadayada

            Level 3 Expert

            76691 Answers

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            22219 Answers

            Kevin Daniels

            Level 3 Expert

            1455 Answers

            Are you a Honda Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...