Question about Hyundai Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The procedure is roughly the same for all mk3 x types.
You need to remove all the screws on the armrest and on the ashtray, then undo all the plastic clips using screwdrivers on the panel.
You find detailed instructions on links below, I quote:
" remove two screws at the bottom of the armrest.
pull out ash tray.
remove screw in the middle of the ash tray holder.
pull up on armrest, it should pop up, then pull it out
start at bottom right of door and start popping out the plastic clips (all the way around the door)
(remove speaker wires)
push up door panel - done"
WikiAnswers - How do you remove a rear door panel in a Jaguar XJ6
Also from manual:
Disconnect vehicle battery ground lead.
Remove the door trim pad veneer panel.
Remove the upper trim pad.
Remove the door armrest.
From inside the door pocket, release the puddle lamp (1 Fig.1) securing quarter turn fastener.
Undo and remove fixing (3 Fig.1), (front door only)
Carefully release lower trim pad fir tree fasteners.
To avoid damage and distortion of the door metal, lift the lower trim pad complete with clip and clip retainer.
Carefully pull the trim pad away from the door panel.
Disconnect the multi-plugs (1 Fig.2) and remove the lamp.
Carefully displace the trim pad (2 Fig.1) from the door retaining clips.
Disconnect the multi-plugs (2 Fig.2) and (3 Fig.2).
Remove the door pocket.
Displace and remove the retaining clips and remove the trim..
Refit in the reverse order of the removal procedure. Check the trim pad retainers for damage before refitting.
Before refitting the lower trim pad, remove the clip retainer from the pad and and reposition retainer to the door.
ndo door handle escutcheon screw and remove escutcheon
Remove the door trim pad veneer panel.
Undo and remove the upper trim pad securing screws.
Remove the chrome strip.
Undo and remove the top channel securing nuts.
Displace and remove the top channel assembly.
Place the trim pad aside (Fig. 1).
Refit in the reverse order of the removal procedure.
Thanks Jaguar XJ6 Interior Lights
I will be grateful if you can rate the solution given.
Posted on Feb 25, 2009
The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.
Posted on Mar 21, 2009
Answer There is a small black plastic piece that surrounds your door handle. You MUST take that off, I find a small flat tip screw driver works best. The plastic cover that goes on the inside part of the door where your mirror is should be removed, makes it a lot easier to remove door trim: No screws on that part just grab from both sides and pull. 3 screws on bottom and 1 screw inside the armrest. The window crank, easiest way tried and true, shoestring, pull handle towards inside of car until you have enough room to fit the shoestring between crank and plastic washer. Give it a pull back and forth and it'll pop right off; clip should stick to shoestring as an added bonus.
Posted on Jun 01, 2009
You'll need a torx bit for the bottom screws. The door handle comes apart (using a screw driver) to expose 2 phillips screws holding the door handle to the door, after you get those out, pop the rest of the push clips out by firmly pulling on the door panel near the bottom, There may also be another screw on the TOP Front (near the mirror) very small phillips. Once you have the door panel loose, lift UP on the door panel to remove. Once you get that panel off, you'll have to remove all the other screws to get the window regulator out (lots of 10mm bolts). Unclip / unconnect the connections etc..
Posted on Jul 11, 2009
SOURCE: rear door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
Tips for a great answer:
Dec 23, 2016 | Pontiac Cars & Trucks
Jan 20, 2016 | 2005 Dodge Grand Caravan
Jan 13, 2016 | Cars & Trucks
Mar 30, 2015 | 2013 Kia Sorento
Oct 23, 2010 | 2004 Pontiac Grand Prix
Oct 10, 2009 | 2000 Jaguar S-Type
Aug 28, 2009 | 2004 Land Rover FreeLander
May 07, 2009 | 1994 Mercury Cougar
Apr 07, 2009 | 2000 Ford Taurus
Feb 21, 2009 | 1996 Ford Thunderbird LX
24 people viewed this question
Usually answered in minutes!