Question about 2006 Ford Bantam 1.3i

Open Question

Ford bantam How to replace front brake discs?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
scott586
  • 41 Answers

SOURCE: How to remove disc brake rotor on a 1992 Ford Explorer 4-wheel drive

It should just pull off once you have taken the caliper off. It may be seized in place, if thats the case try spraying the back of it with some sort of penetrating oil, let it sit for a bit. THen put some heat on it if you have torches, or beat it with a hammer. Sounds kind of crude...but it works

Posted on May 07, 2009

Ad
tragedy lok
  • 266 Answers

SOURCE: replace front brake disc on 1997 ford f250 4x4

remove tire,loosen and remove caliper 2 bolts on rear side of caliper,usually a allen/torque wrench or a standard wrench if u got all 3 ur good,fully remove caliper disc slides right off studs,new caliper will be thicker,which requires the piston behind the pad to be moved in, u can use a large c lamp be very careful while tightening down on piston not to brake it usually lay something across the piston put the clamp on that piston must go in far enough to allow pad to slide over new disc good luck its easy and pretty self explanitory

Posted on Oct 28, 2009

  • 312 Answers

SOURCE: brake pad replacement 1996 ford thunderbird

1. Raise and support the vehicle
2. Remove the desired wheel
3. Loosen/remove the two caliper retaining bolts.
4. Remove the caliper from the wheel
5. Using a C-clamp, depress the caliper piston until it's completely recessed.
6. Remove the old brake pads
7. Install the new brake bads on the caliper
8. Reinstall caliper on the disc
9. Reinstall/tighten the calpier bolts
10. Put the wheel back on
11. Lower the vehicle.

*** When you are getting set let the car roll a few revolutions of the wheel to keep the pads off the disc. It will make it easier to get the caliper off.

Posted on Nov 05, 2009

  • 438 Answers

SOURCE: I am replacing the front disc brakes on a 1999 escort

i shall help u by telling the procedure. first remove the brake cable from the caliper. now check for the dusts if any and re insert into the disc caliper now bleed the brake master cylinder. strongly kick the brake.keep it in pressed condition and pour in the brake oil. now release the brake pedal and push it for two times and then release.now the oil will be evenly distributed into your master cylinder. To be noted that connection goes directly from brakes master cylinder to the brake pedal. from the brake master cylinder the connection goes to the two wheels(front).check for any oil leakage.

Posted on Feb 13, 2010

  • 118 Answers

SOURCE: I am hearing grinding when I brake on my Ford

Just take the back tires off and look at them

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 ford bantam rocam 1600 I I did the engin but now if I start the bakkie and take the steering wheel the front weels make a vibration


inspect the front wheel nuts for tightness
check the tyres are not out of round and sound
che k the steering rack for wear
balance front wheels even a wheel alignment
brakes
check the calipers for sticking slide guides
rotors for warp
and brake pad wear

26223301-evitet2jl4lc3pmm5nhbf4w4-3-0.jpg

Jun 22, 2016 | Ford Cars & Trucks

1 Answer

Can I remove brake equaliser on 1996 ford bantam


Absolutely NOT. You will find your brakes will operate erratically. The rear brakes will lock up and skid way before the front brakes lock up. The amount of fluid the rear brakes take to apply even pressure is way more that the disc brakes up front. That is the purpose of the equalizer. It makes sure an equal amount of braking force is applied to all four wheels.

Nov 20, 2015 | Ford Cars & Trucks

1 Answer

How to replace front shocks


check for a faulty climate control module.

Mar 16, 2015 | 2005 Ford Bantam 1.6i

1 Answer

How stop rear brakes binding ford bantam


If the disc brakes are binding this usually means one or both calipers are not releasing fully. This is usually a fault in the caliper, but can also be caused by such things as bad break hose, faulty master cylinder, or brake pedal not returning fully due to linkage issues. Jack up rear of car and put it on stands, try to turn each rear wheel to see which is binding. Both? check brake hose for interior rubber breakdown or master for failure to fully release.

Dec 26, 2014 | Ford Cars & Trucks

1 Answer

Can l kindly have a diagram on how to replace brake shoes on a ford bantam rocam 1.3


Cannot help you here as never seen a bantam but as its a ford i would assume its the same as a ford escort or fiesta ,their not difficult trust me the foreward leading shoe has a leading edge the leading shoe is the thicker one going to the front of the car.the handbrake cable fits to the trailing shoe the one with the arm on for the cable ,the auto adjuster fits just below the slave cylinder with the adjuster to the right or rear of the car smaller spring to the lower and spring with the two coils either end to the top some have a snail cam adjuster some have a little wheel depends on the age of the vehicle ,yes its fiddly but its not a difficult job

Jul 26, 2014 | Cars & Trucks

1 Answer

2005 1.3i ford bantam front wheel bearings torque settings?


Get a Hanes manual from PepBoys for your vehicle.They carry them all.You'll find all specs in there.

May 02, 2014 | 2005 Ford Bantam 1.3i

1 Answer

Ford bantam diesel bakkie 2004


check the vaccuum pipe to the brake booster ,sounds like the booster is not receiving vacuum to power assist your brakes

Jan 15, 2014 | Cars & Trucks

2 Answers

How to bleed n Clutch system on Ford Bantam 1.3


I have a Ford Bantam 1.3 bakkie and the clutch fluid is running / leaking into the vehicle itself. How do we replace?

May 03, 2012 | 2006 Ford Bantam 1.3i

Not finding what you are looking for?
2006 Ford Bantam 1.3i Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...