Question about 1998 Dodge Ram 1500 4WD

1 Answer

Proper installation instructions for Rocker Arm Installation 1998 Dodge 5.9 360.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers

Locate v8 on crankshaft damper(147 degrees ATDC). rotate engine until v8 lines up with TDC mark on timing cover. install rocker arm and pivot assemblies and torque to 21 ft. lbs. wait 5 minutes before starting vehicle to allow lifters to bleed down correctly

Posted on May 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Ford windstar 3.8L head rocker arm installation and torque


Hey Rene, did you try autozone library its all free and easy to use

Nov 08, 2014 | 1998 Ford Windstar

1 Answer

Rocker arm installation 99 monte carlo 3.1


Once valve cover is removed then there is a single bolt holding rocker arm assembly to head usually a 10mm bolt remove and remove rocker are and stand replace all make sure that you align stand up as you tighten bolt torque to 10-15 ft lbs + 30 degrees

Mar 21, 2014 | 1999 Chevrolet Monte Carlo

1 Answer

I have a 1996 Buick lesabre with the 3.8 liter v6 motor. I just did a top end gasket set and need to know how to adjust the rocker arms. Can anyone help? I know I need to start on compression stroke to...


zjlimited_2060.jpg

Fig. 7: Rocker arms and related components - 1991-99 VIN L engine and 1998-99 VIN 1 engine (click image for zoom)

  1. Clean the rocker arms and pedestal bolts in a suitable solution and inspect for wear. Make sure to clean all of the thread adhesive from the rocker arm pedestal bolts.

To install:
  1. If removed, install the pushrods and make sure they seat in the lifter.
On 1998-99 vehicles, the bolts rocker arm bolts are designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do NOT use a bolt which is stronger in this application. If the proper bolt is not used, the parts will not be tightened correctly, and part or system damage may occur.
  1. Apply a threadlocking compound to the bolt threads before reassembly.
  2. Install the pedestal and rocker arm assemblies, then tighten the retaining bolts as follows:
    1. 1988-92 vehicles: 28 ft. lbs. (18 Nm).
    2. 1991-98 vehicles: 19 ft. lbs. (29 Nm), plus an additional 90° with a torque angle meter.
    3. 1999-99 vehicles: 11 ft. lbs. (19 Nm), plus an additional 90° with a torque angle meter.

  3. Install the valve cover(s), as outlined earlier, then connect the negative battery cable.
  4. Start engine and check for fluid leaks and listen for valve train noise.
I hope this helps, and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment.

Have a nice day and thanks for using FixYa.

Jose.

Oct 17, 2011 | 1996 Buick LeSabre

1 Answer

How do i replace the window shield wiper blade


The 1998 Dodge Grand Caravan has the most common hook-end wiper arms. See related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

1998 Dodge Grand Caravan Wiper Blade Installation Videos (hook front, hook rear)

1998 Dodge Grand Caravan Wiper Blade Size Options w/Correct Lengths & Attachments

Sep 09, 2011 | 1998 Dodge Caravan

1 Answer

How do i remove the windshield wiper blade


The 1998 Dodge Grand Caravan has the most common hook-end wiper arms. See related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

1998 Dodge Grand Caravan Wiper Blade Installation Videos (hook front, hook rear)

1998 Dodge Grand Caravan Wiper Blade Size Options w/Correct Lengths & Attachments

Sep 09, 2011 | 1998 Dodge Grand Caravan

1 Answer

How do I adjust the valves on a 1998 old bravada 4.3 vortec


You don't. They are non-adjustable hydraulic lifters. GM's spec for torque on the rocker arm nuts: Tighten the valve rocker arm ball studs to 47 N·m (35 lb ft). Once the valve rocker arm nuts are installed and properly torqued, no additional valve lash adjustment is required.

Aug 05, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

I replaced the lifters in my 2000 galant 2.4 L and i need to know what to torque the rocker arm shafts to.


1.5 and 1.8 engines:
* Install the rocker arm and shaft assemblies. Tighten the rocker arm shaft retainer bolts to 23 ft. lbs. (32 Nm).

* Check valve adjustment and install the valve cover. Tighten the valve cover bolts to 16 inch lbs. (1.8 Nm) for the 1.5L engine or to 29 inch lbs. (3.3 Nm) for the 1.8L engine.



2.0 engine
* Lubricate the rocker shaft with clean engine oil and install the rockers and springs in their proper places.

* Install the rocker shaft assemblies on the engine. Tighten the bolts gradually and evenly to 21-25 ft. lbs. (29-35 Nm).



2.4 engine

fa2bc50.jpg

Fig. Rocker arm shafts and components-2.4L engine



* Fit the rocker shaft springs from above and position them so that they are at right angles to the plug side. Install the rocker springs before installing the exhaust side rocker shaft and rocker arm assembly.

* Install the exhaust side rocker shaft assembly in the engine. Tighten the rocker shaft mounting bolts gradually and evenly to 23 ft. lbs. (32 Nm).
* Remove the lash adjuster retaining tools.
* Install the rocker cover and tighten the mounting bolts to 30 inch lbs. (3 Nm).

* Reinstall the spark plug wires to the spark plugs.



Hope helps.

Sep 06, 2010 | Mitsubishi Galant Cars & Trucks

2 Answers

Need instructions on how to change the lifters in my 1998 Chevy S10 2.2L


Please don't forget to rate!!!!

2.2L Engine When installing new lifters, a pre-lube should always be applied to the lifter body. It is also a good idea to prime hydraulic lifters by submerging them in clean engine oil and depressing the plunger using an old pushrod. This allows the internal components of the hydraulic lifter to coat with oil before initial operation in the engine. All lifters should be replaced when a new camshaft is installed.
If any valve train components (lifters, pushrods, rocker arms) are to be reused, they must be tagged or arranged during removal to assure installation in their original locations.
  1. Remove the rocker arm cover.
  2. Remove the cylinder head assembly from the engine.
  3. Remove the bolts retaining the lifter anti-rotation brackets, then remove the brackets.
  4. Remove the hydraulic roller lifters from the bores.
  5. Inspect the lifter and lifter bore for wear and scuffing. Examine the roller for freedom of movement and/or flat spots on the roller surface.

a3ab0ce.gif
Remove the bolts retaining the lifter anti-rotation brackets ...


bb0d44a.gif
... then remove the anti-rotation brackets


79533e9.gif
The lifters are located in bores in the engine block


a298166.gif
Use a lifter removal tool to remove the lifters from the bore

To install:
If installing a new lifter, coat the lifter body with a suitable camshaft pre-lube
  1. Install each hydraulic lifter to its bore being careful to align the flat sides (top) of the lifters with the flat sides of the anti-rotation brackets. When properly installed the flat sides of each lifter are aligned parallel to the anti-rotation bracket. The roller at the bottom of the lifter is parallel to the camshaft lobe.
Make sure to properly align and install each lifter as improper installation of the lifters or brackets could result in engine damage.
  1. Install the anti-rotation bracket retaining bolts and tighten to 97 inch lbs. (11 Nm).
  2. Install the cylinder head.
  3. Install the rocker arm cover.

d477687.gif
Removing the hydraulic roller lifter from the 2.2L engine

Feb 06, 2010 | Chevrolet S 10 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...