Question about 2000 Nissan Xterra

Open Question

2000 nissan xterra fuel injector connector disconnect

How does the electrical connector disconnect from the injector

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SUL827
  • 93 Answers

SOURCE: 2001 Nissan Xterra

Most likely corrosion on the sending unit connector. If corroded will need sending unit assembly. To check lift up passenger side rear seat cushion and remove the top and bottom plates, fuel tank sender is right below.

Posted on Sep 16, 2008

rick_amick
  • 69 Answers

SOURCE: disconnect the electrical connector

There should be just a clip on the connector that pops up and releases from the bulb.

Posted on Apr 05, 2009

glamarre82
  • 140 Answers

SOURCE: fuel injectors on 1982 Nissan 280zx will not open. I

All you have to is check if the fuse or relay are working. If they are, your injectors should be replaced. In the future, use a fuel injector/ carburetor cleaner after every fill up.

Posted on Sep 11, 2009

  • 59 Answers

SOURCE: Nissan xterra 2000, 3.3 L, 4x4,automatique, hold

Instrument.

Posted on Mar 03, 2010

SOURCE: I NEED TO KNOW HOW TO REMOVE AND REPLACE FUEL PUMP

You have to remove or drop the fuel tank
All or most vehicle wire connectors have a
tab to press or lift to unlock
For the fuel lines you can get just a couple
release tools at most auto parts stores or online.
I would go to YOU TUBE VIDEO & watch first

Posted on Aug 12, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nissan xterra 2000 that emmit black smoke and also comsume fuel. what might be the cause?


Might be a valve problem. Disconnect the battery to reset the computer for about 5 min. Reconnect the battery cable and see if there is any difference. Sounds like 'fuel-rich' mixture causing BLACK smoke.

Jan 20, 2015 | 2000 Nissan Xterra

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

My nissan xterra 2000 v6 right side cylinder plug is having black fluffy substance stuck on the plug


Sounds like carbon fouling. Easy fix is run an aggressive fuel injector cleaner as recommended by your local parts store through the gas tank. Also ensure that spark plug wire is firmly attached. If you took the plug out-you know it is a pain to get to it! A easy way to see is to start motor and idle, pull #6 wire off at distributor when it should be attached to plug and see if the idle changes. If it doesn't, the wire is not plugged on the spark plug or the rotor/distributor may be faulty.

Another more difficult task may be the removal and replacement of the fuel injectors them selves (or cleaning by a specialty shop). Good Luck!

Oct 29, 2011 | 2000 Nissan Xterra

2 Answers

Can not find the back spark plug hole


if you go down right beside the intake manifold you will be able to get to it

Sep 09, 2011 | 2000 Nissan Xterra

1 Answer

2000 xterra changed the knock sensor and now putting up a 505 code


CODE PO505 - IDLE SPEED CONTROL SYSTEM MALFUNCTION.SOUND LIKE IDLE SPEED CONTROL ELECTRICAL CONNECTOR IS DISCONNECTED OR HAS FAILED.

Oct 13, 2010 | Nissan Xterra Cars & Trucks

3 Answers

I am remove heater core from nissan xterra 2000 do i need to remove the evaporator


2000-02 Frontier And Xterra
  1. Disconnect both the negative (1st) and positive (2nd) battery cables.
  2. Remove the steering wheel by performing the following procedure:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Remove the lower lid and disconnect the driver-s air bag module connector.
  2. Remove both side lids.
  3. Using the Tamper Resistant Torx® Wrench size T50, remove the special bolts from both sides of the steering wheel and discard them.
  4. Remove the SRS module from the steering wheel.

CAUTION Always store the SRS module face up.
  1. Position the steering wheel in the straight-ahead position.
  2. Disconnect the horn connector and remove the steering wheel nut.
  3. Using a steering wheel puller, press the steering wheel from the steering column.
  1. Remove the passenger-s side air bag by disconnecting or removing the following items:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Open the glove box door.
  2. Working inside the glove box, open the lower instrument panel lid.
  3. Remove the passenger-s air bag module connector clip from the lid.
  4. Disconnect the passenger-s SRS module connector.
  5. Remove the glove box and the lower passenger-s side instrument panel.
  6. Using the Tamper Resistant Torx® Wrench size T50, remove the SRS module-to-instrument panel special bolts and discard them.
  7. Remove the 4 SRS module-to-instrument panel mounting nuts.
  8. Release the SRS module-to-instrument panel clips and remove the SRS module.
CAUTION Always store the SRS module face up.
  1. Drain the cooling system into a clean container for reuse.
  2. Working inside the engine compartment, disconnect the 2 heater hoses from the heater core.
  3. Discharge and recover the air conditioning system refrigerant.
  4. Disconnect both refrigerant lines from the evaporator core. Plug the lines to prevent moisture from entering the system.
  5. Remove the glove box and the mating trim.
  6. Disconnect the thermal amp connector.
  7. emove the air conditioning housing assembly from the vehicle.
  8. Remove the instrument panel assembly by performing the following procedure:
    1. Remove the 4 steering column cover screws; then, separate and remove the steering column covers.
    2. Remove the 2 driver-s side lower instrument panel screws and the lower instrument panel.
    3. Remove the 4 cluster cover screws and the cluster cover.
    4. Remove the 6 combination meter screws; then, disconnect the combination meter electrical connector and remove the meter.
    5. Remove the 2 glove box screws and the glove box.
    6. Remove the 2 instrument stay cover screws; then, disconnect the electrical harness connectors and remove the stay cover.
    7. Remove the 2 cluster lid -C- screws; then, disconnect the electrical harness connectors and remove the cluster lid -C-.
    8. Remove the 4 audio and deck pocket screws; then, disconnect the electrical harness connectors and remove the audio and deck pocket.
    9. Disconnect the ASCD main switch connector.
    10. Remove the 2 meter cover screws; then, disconnect the electrical harness connectors and remove the meter cover.
    11. Remove the 4 air conditioning-heater control screws; then, disconnect the control cables and remove the air conditioning-heater control.
    12. Remove the front pillar garnish.
    13. Remove the 3 instrument panel assembly nuts and 2 bolts; then, remove the instrument panel.
  9. Remove the heater housing assembly.
  10. Remove the heater core from the heater housing assembly.

continue...

Jul 16, 2010 | 2000 Nissan Xterra

2 Answers

HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA



Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Mar 31, 2010 | 2005 Nissan Xterra

1 Answer

My 2000 Nissan Xterra died the other day. It felt like it was "missing" while I was driving down the interstate. Took it into shop, they suggested fuel injector cleaning which seemed to work for a day. ...


Could be the distributor. Bearings are notorious for failing which affects the cam position sensor in the unit. Did you have any codes thrown to the display ?

Dec 22, 2009 | 2000 Nissan Xterra

1 Answer

Disconnect the electrical connector


There should be just a clip on the connector that pops up and releases from the bulb.

Apr 04, 2009 | 2003 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...